E-29
• To toggle auto repeat between on and off, press D while the on/off setting is
flashing in the left digital dial.
4. Press A to exit the setting mode.
• The auto-repeat on ( ) indicator is displayed on the Countdown Timer Mode
screen while this function is turned on.
E-28
To configure countdown start time and auto-repeat settings
1. While the countdown start time is shown in the left
digital dial in the Countdown Timer Mode, hold down
A for about three seconds until the hour setting of the
countdown start time starts to flash. This is the setting
mode.
• If the countdown start time is not displayed, use the
procedure under “To use the countdown timer” (page
E-27) to display it.
2. Press C to move the flashing in the sequence shown
below, and select the setting you want to change.
Start Time
(Hours)
Start Time
(Minutes)
Auto-Repeat
On/Off
3. Perform the following operations, depending on which setting is currently selected
in the left digital dial.
• While the start time setting is flashing, use D (+) and B (–) to change it.
Start time
(Hours : Minutes)
Auto-repeat on
E-27
To use the countdown timer
Press D while in the Countdown Timer Mode to start the countdown in the left digital
dial.
• When the end of the countdown is reached, the alarm will sound for 10 seconds or
until you stop it by pressing any button.
• If auto-repeat is turned off, the countdown time is reset to its starting value
automatically after the alarm stops.
• If auto-repeat is turned on, the countdown will restart automatically without pausing
when it reaches zero.
• The countdown timer measurement operation continues even if you exit the
Countdown Timer Mode.
• Press D while a countdown operation is in progress to pause it.
Press D again to resume the countdown.
• To stop a countdown timer operation completely, first pause it (by pressing D),
and then press A. This returns the countdown time to its starting value.
E-26
Countdown Timer
You can set the countdown start time within a range of
one minute to 24 hours. An alarm sounds when the
countdown reaches zero.
• You also can select auto-repeat, which automatically
restarts the countdown from the original value you set
whenever zero is reached.
• All of the operations in this section are performed in the
Countdown Timer Mode, which you enter by pressing
C (page E-7).
Seconds
Auto-repeat off
Start time
(Hours : Minutes)
E-25
To measure times with the stopwatch
Elapsed Time
D D A
Start Stop Reset
Lap Time
D A A D A
Start
(LAP displayed)
Lap
(Lap01)
Lap
(Lap02)
Stop Reset
Split Time
D A A D A
Start
(SPL displayed)
Split Split release Stop Reset
E-24
To perform a split time measurement
Select split time (SPL) measurement and then perform the
following button operations.
D Start ➝
A Split ➝ A Split Release* ➝
D Stop ➝
A Reset
* The split time is released automatically if you do not
press A within about 12 seconds.
• You can press A
to take split readings as many times
as you like.
• The stopwatch continues elapsed time measurement
internally while a split time reading is displayed.
• Pressing
A while a split time is displayed will switch
back to normal elapsed time measurement. The
elapsed time will appear in the left digital dial.
• You also could press D to stop elapsed time
measurement instead.
• Pressing
D to stop elapsed time measurement
displays the time (and speed if a distance is specified)
of the final split (which is the overall elapsed time).
Hours
Speed hand
(calculated)
Minutes
Seconds
1/1000 seconds
E-23
Split Time
Split time readings appear in the left digital dial. They
show the time elapsed since the beginning of the current
time measurement.
• If you want the watch to calculate the speed of the race,
specify the race distance for the distance setting (page
E-15).
• For split time readings, you can specify the total race
distance only. Though the watch will indicate a speed
each time you take a split reading, they will be based
on the total race distance, and so they will not indicate
actual intermediate split speeds.
To set up the stopwatch to take split time readings
1. In the Stopwatch Mode, make sure the stopwatch is stopped and reset to all zeros.
• If you need to reset the stopwatch to all zeros, press A.
2. Make sure that SPL (split times) is shown in the left digital dial.
• If LAP (lap times) is displayed, press A to toggle it to SPL.
Split time
E-22
To perform a lap time measurement
Select lap time (LAP) measurement and then perform the
following button operations.
D Start ➝
A Lap* ➝ A Lap* ➝ D Stop ➝ A Reset
* Lap time remains frozen in the left digital dial for about
12 seconds. After that, elapsed time measurement
reappears.
• You can press A
to take lap readings as many times
as you like.
• While a lap time is displayed, the right digital dial will
alternate between the lap number (#
01 to #99) and the
lap hour value. If you take more than 99 lap readings,
the lap number will restart from #
00 following lap #99.
• Pressing
D to stop elapsed time measurement
displays the time (and speed if a distance is specified)
of the final lap.
Lap number
Speed hand
(calculated)
Minutes
Seconds
1/1000 seconds
Hours
E-21
Lap Time
Lap time readings appear in the left digital dial. They show
the time elapsed since the last lap time reading was taken.
• If you want the watch to calculate the speed of each lap
(when all of the laps are the same distance), specify the
lap distance for the distance setting (page E-15).
• If you want the watch to calculate the speed of the
entire race, specify the race distance for the distance
setting (page E-15). A speed will be indicated each time
you take a lap reading, but these lap speeds will not
indicate actual speed of the entire race.
To set up the stopwatch to take lap time readings
1. In the Stopwatch Mode, make sure the stopwatch is stopped and reset to all zeros.
• If you need to reset the stopwatch to all zeros, press A.
2. Make sure that LAP (lap times) is shown in the left digital dial.
• If (split times) is displayed, press SPL A to toggle it to LAP.
Lap time
E-20
Elapsed Time Measurement
Use the following procedure to measure elapsed time, without taking lap time or split
time readings.
To perform elapsed time measurement
Select split time (SPL) measurement and then perform the following button operations.
D Start ➝ D Stop ➝ A Reset
• If you have a distance value (page E-15) specified for the current elapsed time
measurement, the right dial display segments and speed hand will indicate the
speed when you press D to stop the elapsed time operation.
• After pressing D to stop an elapsed time operation, you could press D again to
restart from the point where you left off.