Extron P/2 DA2xi Bruksanvisning
Les nedenfor 📖 manual på norsk for Extron P/2 DA2xi (5 sider) i kategorien Mottaker. Denne guiden var nyttig for 2 personer og ble vurdert med 4.5 stjerner i gjennomsnitt av 2 brukere
Side 1/5
1
P/2 DA2xi • User Guide
The P/2 DA2xi is a high performance one input, two output distribution amplier that
accepts video input from a VGA-QXGA compatible PC and distributes that signal to
separately buffered outputs. The output can be extended with Extron MHR cables
up to 250 feet in length (XGA resolution signal).
The P/2 DA2xi routes all video ID bits to its local monitor output to allow for automatic
resolution selection by DDC1 and DDC2 (plug and play cards and projector).
FCC Class A Notice
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part15 of the
FCC rules. The ClassA limits provide reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment
in a residential area is likely to cause interference. This interference must be corrected at the expense of the user.
NOTE: For more information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics,
see the “Extron Safety and Regulatory Compliance Guide” on the Extron website.
Specifications Availability
Product specications are available on the Extron website, www.extron.com.
Features
• Power LED — useful in system troubleshooting
• Impedance DIP switches — for solving laptop compatibility problems and reection problems due to long cable runs
• Bandwidth — 300 MHz (-3 dB) RGB video bandwidth maintains signal integrity
• ID bits pass-through — routes ID bits to the local monitor output to allow automatic scan rate selection by DDC
Mounting the P/2 DA2xi
Attention:
• Installation and service must be performed by authorized personnel only.
• L’installation et l’entretien doivent être effectués par le personnel autorisé uniquement.
The 1-inch high, quarter rack width P/2 DA2xi can be placed on a tabletop, mounted on a rack shelf, mounted under a desk or
tabletop, or mounted on a projector bracket.
Figure 1. Tabletop Placement
Attach the four included rubber feet to the bottom of the distribution amplier and place it in any convenient location.
2
P/2 DA2xi • User Guide (Continued)
Optional Mounting
NOTE: Accessory part numbers are available on the Extron website, www.extron.com.
The P2 DA2xi can be mounted using the following mounting kits:
• RSU 126 6” deep universal rack shelf kit
• RSB 126 6” deep basic rack shelf
• RSU 129 1U universal rack shelf kit
• RSB 129 1U basic rack shelf
• MBU 125 1U under-desk mounting kit
• MBD 129 1U through-desk mounting kit
The unit can be mounted in the front or the rear of the rack, as shown in the following illustration.
1. Remove the feet from the bottom of the P/2 DA2xi, if they
Use 2 mounting holes on
opposite corners.
(2) 4-40 x 3/16"
Screws
1U Universal Rack Shelf
are installed.
2. Mount the unit using two 4-40 x 3/16 inch screws in
opposite (diagonal) corners to secure the P/2 DA2xi
to the shelf.
3. Install false faceplates or other units to the rack shelf.
Under-furniture Mounting
The P/2 DA2xi can be mounted under a table or other horizontal surface using an optional Extron MBU 125 under-desk mounting
kit. Mount the unit under a desk or table, as follows:
1. Secure the under-desk mounting brackets to the distribution amplier with
the four machine screws provided in the mounting kit.
2. Hold the unit with attached brackets against the underside of the desk or
other furniture. Mark the location of holes for screws on the desk.
3. Drill 1/4 inch (6.4 mm) deep, 3/32 inch (2 mm) diameter pilot holes in the
table or desk at the marked screw locations from the underside or inside
(the concealed side) of the furniture, where the distribution amplier will
be located.
4. Insert the four wood screws into the pilot holes. Fasten each screw into
the installation surface until just less than 1/4 inch of the screw head
protrudes.
5. Align the installed screws with the slots in the mounting brackets, and
place the unit against the surface, with the screws through the bracket
slots.
6. Slide the unit slightly forward or back, then tighten all four screws to fasten
it in place.
3
P/2 DA2xi • User Guide (Continued)
Through-furniture Mounting
The distribution amplier can be mounted through a desk or other furniture using an optional Extron MBD 129 through-desk
mounting kit. Mount the P/2 DA2xi through a desk or table, as follows:
1. Loosely attach the mounting brackets to the unit using the four
machine screws and washers supplied with the mounting kit.
2. Hold the distribution amplier against the inside of the surface
through which it will be mounted. Mark the four screw holes on
the inside of the surface to which you are mounting the device.
3. Drill four pilot holes, each 3/32 inch in diameter by 1/4 inch deep,
where you made marks.
4. Using the four wood screws provided, secure the brackets to the
mounting surface.
5. Slide the unit up and down in the mounting brackets until the face
of the unit is at the desired height. Tighten the screws that secure
the bracket in place.
If the screws are inaccessible to a screwdriver:
a. Mark the location of the brackets relative to the screws.
b. Remove the P/2 DA2xi from inside the furniture.
c. Tighten the screws.
d. Replace the unit inside the surface (step 4).
Projector Mounting
The PMK 350 Low Prole Projector Mount Kit is an above-projector mounting kit that attaches to a 1 inch to 2 inches diameter
projector mounting pole. It can hold more than one device, in a variety of sizes. The PMK 350 is available in black or white.
Follow these steps to mount the P/2 DA2xi on the PMK 350 bracket as follows:
1. Remove the front and back panels from the
Extron
PMK 350
Multi-product Projector
Mounting Kit
Extron
P/2 DA2xi
Cover Sheet
Front Plate
Rear Plate
U-bolt
PMK 350, using an Extron Tweeker or other
small Philips screwdriver. (Retain the screws
to reattach the plates when you are nished.)
2. Remove any rubber feet from the bottom of
the P/2 DA2xi.
3. Secure the P/2 DA2xi to one side of the
mounting bracket, using two of the supplied
4-40 x 3/16 inch screws in opposite (diagonal)
corners.
4. Using the two included tie wraps, strap the
P/2 DA2xi power supply to the PMK 350 bracket.
5. Place the bracket around the projector ceiling
mounting pole as shown in the previous illustration.
6. Place the rubberized contoured base against
the pole and opposite the back plate. The pole
should t snugly into the depression in the center
of the contoured base.
7. Align the two slotted holes in the bottom of the L-shaped bracket with the two slotted holes in the base of the PMK 350, on
either side of the opening for the pole. Attach the L-bracket to the base by inserting two provided 6-32 x 5/16 inch screws
through the aligned slots.
8. Insert the two legs of the provided square U-bolt through the following parts in the order they are listed below:
• The slotted holes on the back side of the bracket mount plate
• The round holes in the rubberized contour base
• The round holes in the L-shaped bracket
For a typical (1.5 inches to 2.0 inches diameter) pole — You can use the supplied square U-bolt, which ts a typical
ceiling pole.
For a smaller pole — Locally obtain a square U-bolt that ts your ceiling pole. The slotted holes on the bracket can
accommodate a square U-bolt for pole sizes from 1.0 inch to 2.0 inches in diameter.
Produkspesifikasjoner
| Merke: | Extron |
| Kategori: | Mottaker |
| Modell: | P/2 DA2xi |
Trenger du hjelp?
Hvis du trenger hjelp med Extron P/2 DA2xi still et spørsmål nedenfor, og andre brukere vil svare deg
Mottaker Extron Manualer
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024
Mottaker Manualer
- Mottaker Bosch
- Mottaker Vonyx
- Mottaker Jensen
- Mottaker Hartke
- Mottaker Goobay
- Mottaker Kogan
- Mottaker Sony
- Mottaker Yamaha
- Mottaker Lindy
- Mottaker NuPrime
- Mottaker AudioControl
- Mottaker Rotel
- Mottaker Toa
- Mottaker VMV
- Mottaker S.M.S.L
- Mottaker Kicker
- Mottaker Auna
- Mottaker OSD Audio
- Mottaker DataVideo
- Mottaker Audizio
- Mottaker Blackstar
- Mottaker MB Quart
- Mottaker Aplic
- Mottaker CSL
- Mottaker Advance
- Mottaker Artsound
- Mottaker Yorkville
- Mottaker JBL
- Mottaker Bellari
- Mottaker Match
- Mottaker A-NeuVideo
- Mottaker Monitor Audio
- Mottaker Peavey
- Mottaker Fosi Audio
- Mottaker Antelope Audio
- Mottaker Vaddio
- Mottaker ESX
- Mottaker Omnitronic
- Mottaker Russound
- Mottaker MEE Audio
- Mottaker GigaBlue
- Mottaker Mx Onda
- Mottaker Black Hydra
- Mottaker Electro-Voice
- Mottaker Boss
- Mottaker JL Audio
- Mottaker Shanling
- Mottaker Atlas Sound
- Mottaker Audiolab
- Mottaker Memphis Audio
- Mottaker Primare
- Mottaker PureLink
- Mottaker Kramer
- Mottaker ATen
- Mottaker Yaesu
- Mottaker Musical Fidelity
- Mottaker RDL
- Mottaker Dynacord
- Mottaker Ferguson
- Mottaker REL Acoustics
- Mottaker Inovonics
- Mottaker BZBGear
- Mottaker Ram Audio
- Mottaker Phoenix Gold
- Mottaker HiFi ROSE
- Mottaker Intelix
- Mottaker Comprehensive
- Mottaker Fiio
- Mottaker Lab Gruppen
- Mottaker GlobalSat
- Mottaker AVMATRIX
Nyeste Mottaker Manualer
28 Oktober 2024
27 Oktober 2024
27 Oktober 2024
27 Oktober 2024
27 Oktober 2024
27 Oktober 2024
27 Oktober 2024
27 Oktober 2024
27 Oktober 2024
27 Oktober 2024