Havis C-SM-SA Bruksanvisning
Les nedenfor 📖 manual på norsk for Havis C-SM-SA (5 sider) i kategorien Bilsett. Denne guiden var nyttig for 6 personer og ble vurdert med 4.5 stjerner i gjennomsnitt av 2 brukere
Side 1/5
C-SM_INST_ -10 9
INSTALL INSTRUCTIONS C-SM SERIES
ANGLED HEAVY DUTY CONSOLE & ACCESSORIES
TOOLS REQUIRED:
Standard socket set w/ 6”extension
Metric socket set w/ 6” extension
Standard wrench set
Metric wrench set
Torx bit set w/ driver
Slide ¼” nuts into extrusion.
This can be done on inside of
console at top of extrusion.
Tunnel Plate (C-TMW-xx)
(Part # varies depending on vehicle type)
Pentex Printer
Mount
( )C-PMS
Console Extension
(C-SM-600, 800 or
1200)
Angled Heavy Duty
Console
(C- - )SM 830 or 1225
Keyboard/Laptop
Platform
( ) C-SM-SA-1
Monitor Platform
(C-SM-MMP)
C-SM_INST_ -10 9
Always!
¾ Read all instructions before installing any Havis, Inc. products.
¾ Check for obstructions (Wire, brake lines, fuel tank, etc.) before drilling any holes!
¾ Use hardware provided with install kit
SUB ASSEMBLY:
1. Install Tunnel Mount into vehicle. (See Tunnel Mount
specific install instructions.)
2. Determine desired height of console and console
accessories prior to mounting in vehicle.
INSTALLATION:
1. ADJUST CONSOLE HEIGHT: (See Figure #1)
• To adjust height remove carriage bolts on side
of console.
• Mount necessary accessories to side of console.
(Monitor platform, keyboard/laptop platform,
printer, etc. See instructions below.)
• With all accessories and height determined, re-attach
carriage bolts and nuts to console.
2. ATTACH MONITOR PLATFORM: (See Figure #2)
• Mounting platform attaches to side of console using
supplied carriage bolts and serrated nuts.
• Monitor mounting platform will mount to front row of
holes on console.
• Attach C-UMM-101 and C-MM-XXX brackets to
monitor platform prior to attaching to console.
Note: Prior to mounting accessories to side of Angled Heavy Duty console
be sure to adjust height.
3. ATTACH KEYBOARD/LAPTOP PLATFORM:
(See Figure #3)
• Mounting platform attaches to side of console using supplied
• carriage bolts and serrated nuts.
• When using platform for a keyboard, mount on rear rows
of holes on console.
• When using platform for a laptop, you have the option of using
any row of holes for desired height.
• Attach tilt / swivel, keyboard/laptop mount to swing arm assembly.
RE: C-MD-202, C-KBM-101 (sold separate)
Note: Prior to mounting accessories to side of Angled Heavy Duty console be sure to adjust height.
Height Adjustment
Figure #1
Figure #2
Mounts to sides of
Console
Figure #3
Mounts to sides of
Console
C-SM_INST_ -10 9
4. ATTACH PENTEX PRINTER BRACKET: (See Figure #4)
• Printer bracket attaches to front side of console.
• When mounted properly, printer housing will slide toward passenger side seat.
• Attach to Angled Heavy Duty console using supplied screws and Keps nuts.
5. MOUNT CONSOLE TO TUNNEL PLATE:
• Slide ¼-20 x ¾” bolts into slots of Tunnel Plate.
• Place Angled Heavy Duty console over ¼” bolts.
• Position console and attach to Tunnel using ¼-20 serrated nuts.
6. (C-SM-600, 800, 1200 see Figure 5) ATTACH CONSOLE EXTENSION:
• With Angled Heavy Duty console attached to Tunnel, position and attach 6” console
extension. **A spare plastic end cap is provided in case you choose not to attach
consoles together. Simply peel and stick to console end plate if desired.
• Slide (2) ¼-20 x ¾” hex head bolts into slots of Tunnel Plate.
• Place console extension and bolt down using ¼-20 serrated nuts.
• Connect opposite end-to-end plate of Angled Heavy Duty housing. (Slot to slot).
Adjust height as desired.
• Wire and install control heads and accessories.
Mounts to
Angled Heavy
Duty console
Mounting
Hardware
Figure #4 Figure #5
Tunnel Plate
Hardware
A spare plastic end
cap is provided in
case you choose not
to attach consoles
together
Produkspesifikasjoner
| Merke: | Havis |
| Kategori: | Bilsett |
| Modell: | C-SM-SA |
Trenger du hjelp?
Hvis du trenger hjelp med Havis C-SM-SA still et spørsmål nedenfor, og andre brukere vil svare deg
Bilsett Havis Manualer
8 Januar 2025
8 Januar 2025
8 Januar 2025
8 Januar 2025
8 Januar 2025
8 Januar 2025
8 Januar 2025
8 Januar 2025
8 Januar 2025
8 Januar 2025
Bilsett Manualer
Nyeste Bilsett Manualer
31 Desember 2025
29 Desember 2024
29 Desember 2024
29 Desember 2024
29 Desember 2024
29 Desember 2024
29 Desember 2024
29 Desember 2024
16 Desember 2024
22 Oktober 2024