Ikan RB10 Bruksanvisning
Les nedenfor 📖 manual på norsk for Ikan RB10 (8 sider) i kategorien Lettelse. Denne guiden var nyttig for 3 personer og ble vurdert med 4.5 stjerner i gjennomsnitt av 2 brukere
Side 1/8
Rayden
Quick Start Guide
Rayden LED Lights
What’s Included
RB5
RW5
RB10
RW10
1 x Light Fixture
1 x Yoke Mount
1 x Neutral Density Filter
1 x Power Supply with Cable
www.ikancorp.com | 1.713.272.8822 | sales@ikancorp.com because we’re toofilmmakers
Getting to know your Rayden Lights
PRECAUTIONS
• Keep the fixture away from water and all flammable gases or liquids.
• Use ONLY the recommended batteries.
• Handle the unit with care.
• DO NOT attempt to disassemble or repair the unit without first contacting the service department at www.ikancorp.com
• Keep the unit clean and free of dust. The unit can be cleaned with a soft, dry cloth.
• Use ONLY parts provided by the manufacturer.
• Always use caution when plugging in the fixture.
Mounting the Rayden to a stand
The Rayden LED Light comes with a pre-installed yoke and combo mount. This allows the fixture to easily sit and adjust on any
stand. The 30° yoke gives the light free-range motion without obstructions. The Baby 5/8“ and Junior 1-1/8” Combo Pin allows
the user a wide range of stands. The light can be mounted either horizontally or vertically on a 5/8” baby pin.
Power the LEDs
The Rayden light comes with an included AC power supply and 6 foot cable. This allows the user to plug into any standard 120-
240v electrical outlet. The Rayden LED light can be powered from either an AB Mount pro battery, or a V-Mount battery. The
fixture comes standard with either AB-Mount or V-Mount plates. The plates can be easily removed and replaced for the type of
batteries that are available.
Adjusting the Color & Brightness of the Light
The Rayden LED light is controlled by the large yellow knob on the rear of the fixture. The knob was designed with the idea that
it could be reached and adjusted when the light is up on a stand. The knob has two push settings.
The default setting is the brightness from 10%-100% brightness.
By pressing in on the knob, the color temperature can be adjusted. (Bi-Color lights)
www.ikancorp.com | 1.713.272.8822 | sales@ikancorp.com because we’re toofilmmakers
www.ikancorp.com | 1.713.272.8822 | sales@ikancorp.com because we’re toofilmmakers
Remote Control
The light can be adjusted also using the RF remote control. The use of the remote allows for multiple lights to be connected, as well as
control of the brightness.
Remote Control Button Functions
• Press & Hold “A” for 5 seconds to sync remote control to light(s)
• Press “A” to power ON/OFF (for Daylight Light only)
• Press “A”& "B" to power ON/OFF (for Bi-Color Light only)
• Press “B” to adjust 4 levels of light intensity in increments of 25%
• Press and Hold “B” for 5 seconds to Enable/Disable sound
• Hold down “C” to increase light intensity 0%-100%
• Hold down “D” to decrease light intensity 100%-0%
Optional Accessories
Some other products that work well with the Rayden lights from Ikan include:
HD-STND
ROLLR-STND10
CP-STND-V3
SW-04
KCP-703
Heavy Duty Light Stand
2 Stage Roller Stand 10 ft 6 in
Compact Light Stand Version 3
Safety Wire
Stage Clamp w/ 16mm Stud
Changing the Pro Battery Plate
Adding or removing the pro battery plate on the back of your fixture can be easily achieved.
NOTE: The fixture comes pre-installed with the Gold-Mount battery plate.
The process starts with the removal of the four screws on the four corners of the plate.
Once the screws are removed, separate the plate from the back of the fixture.
Unplug the 2-pin connector from the fixture.
Store the screws and the Gold-Mount in a safe place.
Reattaching the V-Mount plate is a simple process.
Plug the wired 2-pin connector into the fixture where we just unplugged the Gold-Mount plate at the back of the light. Orient the
holes on the plate to match up with the screw holes on the back of the fixture. Using the screws supplied with the V-Mount plate,
screw in the plate until it is snug against the back of the fixture. Do not over-tighten the screws.
You’re now ready to install your battery to the V-Mount plate.
Produkspesifikasjoner
| Merke: | Ikan |
| Kategori: | Lettelse |
| Modell: | RB10 |
Trenger du hjelp?
Hvis du trenger hjelp med Ikan RB10 still et spørsmål nedenfor, og andre brukere vil svare deg
Lettelse Ikan Manualer
19 Oktober 2024
17 Oktober 2024
17 Oktober 2024
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024
Lettelse Manualer
- Lettelse DeWalt
- Lettelse Hama
- Lettelse Neewer
- Lettelse Hazet
- Lettelse Schwaiger
- Lettelse IKEA
- Lettelse Kogan
- Lettelse GoGEN
- Lettelse Integral LED
- Lettelse ET2
- Lettelse Quoizel
- Lettelse Crystorama
- Lettelse Aputure
- Lettelse Media-tech
- Lettelse Klein Tools
- Lettelse Schneider
- Lettelse Fluval
- Lettelse Ryobi
- Lettelse Nanlite
- Lettelse BeamZ
- Lettelse Maxim
- Lettelse Brandson
- Lettelse Aplic
- Lettelse CSL
- Lettelse Bearware
- Lettelse Milwaukee
- Lettelse Showtec
- Lettelse V-Tac
- Lettelse Elation
- Lettelse Chauvet
- Lettelse Aqara
- Lettelse Beghelli
- Lettelse Rosco
- Lettelse DeSisti
- Lettelse Astera
- Lettelse EXO
- Lettelse Profoto
- Lettelse GRE
- Lettelse Perel
- Lettelse Blackburn
- Lettelse Sigma
- Lettelse Rayzr 7
- Lettelse Excello
- Lettelse Genaray
- Lettelse Altman
- Lettelse Setti+
- Lettelse Kanlux
- Lettelse ARRI
- Lettelse Osram
- Lettelse Light4Me
- Lettelse GlobalTronics
- Lettelse Lume Cube
- Lettelse Digipower
- Lettelse ETC
- Lettelse Fiilex
- Lettelse Portman
- Lettelse ColorKey
- Lettelse Litepanels
- Lettelse Perfect Christmans
- Lettelse XQ-Lite
- Lettelse Heitronic
- Lettelse Obsidian
- Lettelse Blizzard
- Lettelse LUPO
- Lettelse Enttec
- Lettelse Fotodiox
- Lettelse GVM
- Lettelse Amaran
- Lettelse Halo
- Lettelse HQ Power
Nyeste Lettelse Manualer
28 Oktober 2024
28 Oktober 2024
28 Oktober 2024
28 Oktober 2024
28 Oktober 2024
28 Oktober 2024
28 Oktober 2024
28 Oktober 2024
28 Oktober 2024
28 Oktober 2024