JBL Grand Touring GTO5060 Bruksanvisning
Les nedenfor 📖 manual på norsk for JBL Grand Touring GTO5060 (8 sider) i kategorien Mottaker. Denne guiden var nyttig for 3 personer og ble vurdert med 4.5 stjerner i gjennomsnitt av 2 brukere
Side 1/8
GTO4060
GTO2060
car audio
power
amplifier
owner’s manual
INSTALLATION
2
THANK YOU
for purchasing a JBL GTO amplifier. In
order that we may better serve you should
you require warranty service for your new
amplifier, please retain your original pur-
chase receipt and register your new JBL
amplifier online at www.jbl.com.
WARNING
Playing loud music in an automobile
can hinder your ability to hear traffic and
permanently damage your hearing. We
recommend listening at low or moderate
levels while driving your car. JBL accepts
no liability for hearing loss, bodily injury or
property damage resulting from the use or
misuse of this product.
IMPORTANT
To get the best performance from your
JBL GTO amplifier, we strongly recommend
that installation be entrusted to a qualified
professional. Although these instructions
explain how to install GTO amplifiers in a
general sense, they do not show specific
installation methods that may be required
for your particular vehicle. If you do not
have the necessary tools or experience,
do not attempt the installation yourself.
Instead, please ask your authorized JBL
car audio dealer about professional
installation.
INSTALLATION
WARNINGS AND TIPS
• Always wear protective eyewear when
using tools.
• Turn off the audio system and other
electrical devices before you start.
Disconnect the (–) negative lead from
your vehicle’s battery.
• At the installation sites, locate and
make a note of all fuel lines, hydraulic
brake lines, vacuum lines and electrical
wiring. Use extreme caution when cut-
ting or drilling in and around these areas.
• Check clearances on both sides of
a planned mounting surface before
drilling any holes or installing any
screws. Remember that the screws
can extend behind the surface.
• Before drilling or cutting holes, use a
utility knife to remove unwanted fabric
or vinyl to keep material from snagging
in a drill bit.
• When routing cables, keep input-signal
cables away from power cables and
speaker wires.
• When making connections, make
certain they are secure and properly
insulated.
• If the amplifier’s fuse must be replaced,
use only the same type and rating as
that of the original. Do not substitute
another kind.
CHOOSING A LOCATION
AND MOUNTING THE
AMPLIFIER
Choose a mounting location in the trunk
or cargo area where the amplifier will not
be damaged by shifting cargo. Amplifier
cooling is essential for proper amplifier
operation. If the amplifier is to be installed
in an enclosed space, make sure there is
sufficient air circulation for the amplifier
to cool itself.
When mounting the amplifier under a
seat, ensure that it is clear of all moving
seat parts and does not affect the seat
adjustments. Mount the amplifier so it
is not damaged by the feet of backseat
passengers. Make sure that the amplifier
is mounted securely using nuts and bolts
or the supplied mounting screws.
Mount the amplifier so that it remains
dry – never mount an amplifier outside
the vehicle or in the engine compartment.
3
INSTALLATION
POWER CONNECTIONS
The GTO amplifiers require a reliable
connection to the vehicle’s electrical
system in order to perform optimally.
See Figures 1 and 2 for terminal
connection locations. Please adhere
to the following instructions carefully:
Ground Connection
Connect the amplifier’s Ground (GND)
terminal to a solid point on the vehicle’s
metal chassis, as close to the amplifier
as possible. Refer to the wire gauge chart to
determine minimum wire gauge size. Sand
away any paint from this location; use a star-
type-lock washer to secure the connection.
Power Connection
Connect a wire (see chart at right for
appropriate gauge) directly to the vehicle’s
positive battery terminal, and install an
appropriate fuse holder within 30cm of the
battery terminal. Do not install the fuse at
this time. Route the wire to the amplifier’s
location, and connect it to the amplifier’s
Positive (+12V) terminal. Be sure to use
appropriate grommets whenever routing
wires through the firewall or other sheet
metal. Failure to adequately protect the
positive wire from potential damage may
result in a vehicle fire. When you are done
routing and connecting this wire, you may
install the fuse at the battery.
Remote Connection
Connect the amplifier’s Remote (REM)
terminal to the source unit’s Remote Turn-
On lead using a minimum of 0.75mm2wire.
NOTE: If your source unit does not have a
remote turn-on connection, connect the
amplifier’s (REM) terminal to the vehicle’s
accessory circuit.
Speaker Connections
Refer to the application guides on the
pages that follow. Speaker connections
should be made using a minimum of
1.5mm2wire.
Wire Gauge Chart
Amplifier Maximum Minimum
Model Current Draw Wire Gauge
GTO2060 33A #8 AWG/8mm2
GTO4060 45A #7 AWG/10mm2
These recommendations assume 3m – 4m
wire runs. If your installation differs mark-
edly, you will need to adjust the wire gauge
accordingly.
Figure 1. Terminal connection end plate for GTO4060.
Figure 2. Terminal connection end plate for GTO2060.
Produkspesifikasjoner
| Merke: | JBL |
| Kategori: | Mottaker |
| Modell: | Grand Touring GTO5060 |
Trenger du hjelp?
Hvis du trenger hjelp med JBL Grand Touring GTO5060 still et spørsmål nedenfor, og andre brukere vil svare deg
Mottaker JBL Manualer
7 Januar 2025
1 Januar 2025
1 Januar 2025
1 Januar 2025
1 Januar 2025
1 Januar 2025
1 Januar 2025
1 Januar 2025
1 Januar 2025
1 Januar 2025
Mottaker Manualer
- Mottaker Bosch
- Mottaker Power Dynamics
- Mottaker Vonyx
- Mottaker Jensen
- Mottaker Hartke
- Mottaker Philips
- Mottaker Goobay
- Mottaker Cayin
- Mottaker Kogan
- Mottaker Sony
- Mottaker Yamaha
- Mottaker Morel
- Mottaker Extron
- Mottaker Lindy
- Mottaker NuPrime
- Mottaker AudioControl
- Mottaker Rotel
- Mottaker Audio-Technica
- Mottaker Toa
- Mottaker Marantz
- Mottaker VMV
- Mottaker S.M.S.L
- Mottaker Kicker
- Mottaker Auna
- Mottaker OSD Audio
- Mottaker DataVideo
- Mottaker Audizio
- Mottaker Blackstar
- Mottaker Hertz
- Mottaker MB Quart
- Mottaker Aplic
- Mottaker CSL
- Mottaker IFi Audio
- Mottaker Henry Engineering
- Mottaker Block
- Mottaker Advance
- Mottaker Artsound
- Mottaker Marshall
- Mottaker Yorkville
- Mottaker Infinity
- Mottaker Helix
- Mottaker Klipsch
- Mottaker Bellari
- Mottaker Match
- Mottaker QSC
- Mottaker A-NeuVideo
- Mottaker Monitor Audio
- Mottaker Peavey
- Mottaker Fosi Audio
- Mottaker Antelope Audio
- Mottaker Vaddio
- Mottaker ESX
- Mottaker Omnitronic
- Mottaker Russound
- Mottaker MEE Audio
- Mottaker GigaBlue
- Mottaker Mx Onda
- Mottaker Black Hydra
- Mottaker Electro-Voice
- Mottaker Boss
- Mottaker JL Audio
- Mottaker Shanling
- Mottaker Atlas Sound
- Mottaker MuxLab
- Mottaker Audiolab
- Mottaker Memphis Audio
- Mottaker Primare
- Mottaker Elektrobock
- Mottaker PureLink
- Mottaker Kramer
- Mottaker ATen
- Mottaker Blustream
- Mottaker Yaesu
- Mottaker Musical Fidelity
- Mottaker Vimar
- Mottaker RDL
- Mottaker Dynacord
- Mottaker Ferguson
- Mottaker REL Acoustics
- Mottaker Inovonics
- Mottaker BZBGear
- Mottaker Ram Audio
- Mottaker Phoenix Gold
- Mottaker HiFi ROSE
- Mottaker Intelix
- Mottaker Comprehensive
- Mottaker Deaf Bonce
- Mottaker Fiio
- Mottaker Lab Gruppen
- Mottaker GlobalSat
- Mottaker AVMATRIX
- Mottaker Imperial
- Mottaker Hifonics
- Mottaker Hotone
- Mottaker Phonic
- Mottaker Taga Harmony
- Mottaker SoundTube
- Mottaker Crest Audio
- Mottaker Mooer
- Mottaker Marshall Electronics
- Mottaker Inter-M
- Mottaker Esoteric
- Mottaker Alto
- Mottaker Mark Levinson
- Mottaker Selfsat
- Mottaker Audibax
- Mottaker Sound Ordnance
- Mottaker Wavtech
- Mottaker Parasound
- Mottaker Benchmark
- Mottaker Koda
- Mottaker Technical Pro
- Mottaker Anthem
- Mottaker Audison
- Mottaker Loxjie
Nyeste Mottaker Manualer
16 Januar 2025
16 Januar 2025
16 Januar 2025
16 Januar 2025
16 Januar 2025
16 Januar 2025
16 Januar 2025
16 Januar 2025
16 Januar 2025
16 Januar 2025