JBL GTO7001 Bruksanvisning

JBL Mottaker GTO7001

Les nedenfor 📖 manual på norsk for JBL GTO7001 (4 sider) i kategorien Mottaker. Denne guiden var nyttig for 7 personer og ble vurdert med 4.5 stjerner i gjennomsnitt av 2 brukere

Last ned PDF

Side 1/4

GTO7001

OWNER’S MANUAL

A B C D

1-5/8"

40mm

25mm

A B

15"

380mm

10-3/8"

263mm

2-1/8"

53mm

Optional RLC

Installation Warnings and Tips

•Disconnect the negative (–) lead from your vehicle’s

battery.

•At the installation sites, locate and make a note of

all fuel lines, hydraulic brake lines, vacuum lines

and electrical wiring. Use extreme caution when

cutting or drilling in and around these areas.

•Choose a e m g l n away f m mosaf ountin ocatio ro isture.

•Make sure there is sufficient air circulation at the

mounting location for the amplifier to cool itself.

•Mount the amplifier, using the supplied hardware.

Specifications

•425W RMS x 1 channel ms nd @ 4 oh a 1% THD + N*≤

•700W chann ms, 14.4V ly RMS x 1 el @ 2 oh supp dan

≤1% + N*THD

•Frequency response: 20Hz – 330Hz (–3dB)

•Maximum input signal: 6V*

•Maximum sensitivity: 100mV*

•THD + N: 0.02%

•Signal-to-noise ratio: 80dBA

(reference 1W into 4 ohms)*

•Signal-to-noise ratio: 107dBA

(reference rated power into 4 ohms)

* CEA-2006A-compliant

Speaker Output Connectors

•Connect the subwoofer to these terminals,

observing proper polarity. Either + or –

terminal may be used. Minimum total

impedance is 2 ohms.

Fuses

•Replace only with the same type and rating.

Power Input Connectors

•+12V: Connect to the positive terminal of the

vehicle’s battery. 4 AWG wire is recommended.

Install an appropriate fuse holder and fuse (75A

minimum) within 18 inches of the battery. Make

sure the wire is not damaged or pinched during

installation. Install protective grommets when

routing wires through the firewall or other sheet

metal.

•GND: Connect to the vehicle’s chassis. Refer to

the picture below.

•REM: Connect to the “Remote Out” lead from

the s un or to a so ce of d ource it ur switche

12 C)V+ (AC .

Aux Output Connectors (RCA)

•Nonfiltered pass-through output. Connect to

the input of an additional amplifier.

Input Connectors (RCA)

•Connect to the RCA outputs from the source unit

or signal processor.

Input-Level Control

•Used to match the input level of the amplifier

to the output level of the source unit.

•See for the adjustment procedure.

Low-Pass Filter Frequency Control

•12dB/octave low-pass filter,

variable from 32Hz to 320Hz.

•See for the adjustment procedure.

DBO (Dyn O iza on) Vari leamic Bass ptim ti ab

Subson h F t W h Vic Hig -Pass il er it ar ble B (Q)ia oost

•For woofers in tuned (vented) enclosures, set

the Frequency control to a value 10Hz below the

enclosure’s resonance (tuned) frequency.

•For woofers in sealed boxes, set the control to

any value you prefer between 30Hz and 50Hz.

•Set the Boost control according to your

preference, being careful not to apply

enough boost to damage your woofer(s).

ADBO High-Pass Filter Frequency control,

variable between 10Hz and 100Hz. See

above for appropriate settings.

BDBO Boost control provides up to

12dB of boost slightly above the high-

pass filter’s frequency. See above for

appropriate settings.

Optional Remote Level Control (RLC) Connector

•Connect the Remote Level Control (RLC) here,

using the RJ-11 cable (supplied with the RLC).

Power On LED

•Illuminated when the amplifier is on.

Protect LED

•Illuminated under any of the following fault

conditions: battery over/under voltage, short

circuit in speaker wires, amplifier is too hot,

amplifier’s output circuit has failed (DC voltage

is present in the amplifier’s output).

Setting Input Level

ATurn Input Level control counterclockwise to

6V (minimim).

BWith a dynamic music track playing, turn the

head unit’s volume control to the 3/4 position.

CTurn Input Level control clockwise until the

bass output is proportionate to the output of

the high-frequency speakers, according to

your preference.

DInput level is now adjusted correctly.

Setting the Crossover

ACrossover setting for subwoofers.

Note: Acceptable frequency ranges are indicated

in gray.

Remote Level Control (Optional)

The Remote Level Control, if installed, will allow

you to adjust the level of bass while seated in the

listening position.

GTO7001 CAR AUDIO SUBWOOFER AMPLIFIER OWNER’S MANUAL

Factory Bolt Ring Connector

Ground Wire

Note: Remove any paint

below ring connector.

Star Washer

This product is designed for mobile applications and is not

intended for connection to the mains.

A valid serial number is required for warranty coverage.

Features, specifications and appearance are subject to change

without notice.

Produkspesifikasjoner

Merke:	JBL
Kategori:	Mottaker
Modell:	GTO7001

Trenger du hjelp?

Hvis du trenger hjelp med JBL GTO7001 still et spørsmål nedenfor, og andre brukere vil svare deg

Ditt navn*

Din e-post*

Skriv spørsmålet ditt her

Mottaker JBL Manualer

JBL DA850 Bruksanvisning

22 Februar 2025

JBL Marine A1504 Bruksanvisning

7 Januar 2025

JBL Power P-7540 Bruksanvisning

1 Januar 2025

JBL Grand Touring GTQ360 Bruksanvisning

1 Januar 2025

JBL CS50.4 Bruksanvisning

1 Januar 2025

JBL Decade DA6502 Bruksanvisning

1 Januar 2025

JBL Decade DA1002 Bruksanvisning

1 Januar 2025

JBL A6000GTi Bruksanvisning

1 Januar 2025

JBL CS60.2 Bruksanvisning

1 Januar 2025

JBL A3000GTi Bruksanvisning

1 Januar 2025

Mottaker Manualer

Nyeste Mottaker Manualer

ETON MA 1 Bruksanvisning

19 Mars 2025

KanexPro SP-1X16SL18G Bruksanvisning

14 Mars 2025

Elipson P1 Bruksanvisning

14 Mars 2025

Elipson Stream S300 Xi Bruksanvisning

14 Mars 2025

Elipson WIIM Mini Bruksanvisning

14 Mars 2025

Rexing RoadMate CPStream Bruksanvisning

13 Mars 2025

Marshall Electronics VDA-108-3GS Bruksanvisning

13 Mars 2025

Rega Brio MK7 Bruksanvisning

12 Mars 2025

Aguilar OBP-3 Bruksanvisning

11 Mars 2025

Aguilar AG Preamp Pedal Bruksanvisning

11 Mars 2025