Kramer 675R/T Bruksanvisning
Kramer
AV-forlenger
675R/T
Les nedenfor 📖 manual på norsk for Kramer 675R/T (4 sider) i kategorien AV-forlenger. Denne guiden var nyttig for 2 personer og ble vurdert med 4.5 stjerner i gjennomsnitt av 2 brukere
Side 1/4
675R/T Quick Start
P/N:
2900- 301389QS
Rev:
1
Scan for full manual
675R/T Kit Quick Start Guide
This guide helps you install and use your 675R/T for the rst time.
Go to www.kramerav.com/downloads/675R/T to download the latest user manual and check if rmware
upgrades are available.
Step 1: Check what’s in the box
675T HDMI Optical Transmitter
2 Power adapters and cords
1 Quick start guide
675R HDMI Optical Receiver
8 Rubber feet
2 Bracket sets
2 OSP-MM1 Fiber Optic SFP+ Transceivers
Step 2: Get to know your 675R/T
675T
#
Feature
Function
1
IN LED
Lights green when a connected source device (with an active HDMI signal) is
detected.
Flashes 4 times green when resetting the device.
O when a connected source device with an active signal is not detected.
2
OUT LED
Lights green when both a connected HDMI source (with an active HDMI signal) and
a connected far-end HDMI acceptor are detected.
O if either the source or the acceptor is not connected, or an active signal is not
present.
3
LINK Tx and Rx LEDs
Light green when OUT IN SFP+ is connected and an active optical link is detected.
Light red when OUT IN SFP+ is connected, an active optical link is not detected. but
O when OUT IN SFP+ is disconnected.
4
ON LED
Lights green when the device receives power.
5
HDMI™ IN Connector
Connect to an HDMI source.
6
OUT IN SFP+ Connector
Connect the ber optic cable to the plugged- SFP+ optical module connect . in or
7
RESET Recessed Button
Press and hold to reset settings to factory default values.
8
SERVICE Micro USB Port
Connect to a PC to perform rmware upgrade (via K-Upload).
9
12V DC Power Connector
12V DC connector for powering the unit.
675R
#
Feature
Function
10
IN LED
Lights green when a connected far-end source device (with an active HDMI signal)
is detected.
O when a connected source device with an active signal is not detected.
11
OUT LED
Lights green when both a connected HDMI source (with an active HDMI signal) and
a connected HDMI acceptor are detected.
O if either the source or the acceptor is not connected, or an active signal is not
present.
12
LINK Tx and Rx LEDs
Light green when OUT IN SFP+ is connected, and an active optical link is detected.
Light red when OUT IN SFP+ is connected but an active optical link is not detected.
O when OUT IN SFP+ is disconnected.
13
ON LED
Lights green when the device receives power.
14
HDMI OUT Connector ™
Connect to an HDMI acceptor.
15
OUT IN SFP+ Connector opening
Connect the ber optic cable to the plugged- SFP+ optical module connect . in or
16
SERVICE Micro USB Port
Connect to a PC to perform rmware upgrade (via K-Upload).
17
12V DC Power Connector
12V DC connector for powering the unit.
Step 3: Install 675R/T
Install 675R/T using one of the following methods:
• Attach the rubber feet and place the unit on a at surface.
• Fasten a bracket (included) on each side of the unit and attach it to a at surface
(see www.kramerav.com/downloads/675R/T).
• Mount the unit in a rack using the recommended rack adapter
(see www.kramerav.com/downloads/675R/T).
• Ensure that the environment (e.g., maximum ambient temperature &
air ow) is compatible for the device.
• Avoid uneven mechanical loading.
• Appropriate consideration of equipment nameplate ratings should be
used for avoiding overloading of the circuits.
• Reliable earthing of rack-mounted equipment should be maintained.
• Maximum mounting height for the device is 2 meters.
Step 4: Connect the inputs and outputs
Always switch OFF the power on each device before connecting it to your 675R/T. For best results, p2-we recommend that you
always use Kramer high-performance cables to connect AV equipment to 675R/T.
Make sure that you always cross-connect the ber connections, Rx OUT to Tx IN and Rx IN to Tx OUT, as unidirectional optical
transmission is carried on simplex ber strands.
To install/replace the OSP-MM1 or other Kramer recommended SFP+
transceiver:
1. Pull the bail out and remove the currently installed transceiver,
insert the protective cap and store in a safe place.
2. Make sure the bail of the new transceiver is pushed up, in the
closed position.
3. Insert the new transceiver into the relevant optical device SFP+ slot
and push it in until it clicks.
4. Remove the protective cap and store it in a safe place for future
use.
Warning: Connecting the SFP+ transceiver to an LC(APC) ber
connector may cause poor performance and damage the connector!
Refer to www.kramerav.com/downloads/OSP-MM1 for more information.
Warning: Class 1 Laser Product
• Invisible laser radiation present.
• Avoid long-term viewing of laser.
• Avoid the use of magnifying viewing aids or instruments (such as binoculars, telescopes, microscopes and
magnifying lenses, but not spectacles or contact lenses).
• Avoid placing optical devices in the emitted beam that could cause the concentration of the laser radiation to be
increased.
Step 5: Connect the power
Connect the power cords to 675T 675R and and plug into the mains electricity.
Safety Instructions (See www.kramerav.com for updated safety information).
Caution:
• There are no operator serviceable parts inside the unit.
Warning:
• Use only the power cord that is supplied with the unit.
• Disconnect the power and unplug the unit from the wall before installing.
Produkspesifikasjoner
| Merke: | Kramer |
| Kategori: | AV-forlenger |
| Modell: | 675R/T |
Trenger du hjelp?
Hvis du trenger hjelp med Kramer 675R/T still et spørsmål nedenfor, og andre brukere vil svare deg
AV-forlenger Kramer Manualer
20 Desember 2024
20 Desember 2024
20 Desember 2024
20 Desember 2024
20 Desember 2024
20 Desember 2024
20 Desember 2024
20 Desember 2024
20 Desember 2024
20 Desember 2024
AV-forlenger Manualer
- AV-forlenger D-Link
- AV-forlenger StarTech.com
- AV-forlenger Extron
- AV-forlenger Lindy
- AV-forlenger Digitus
- AV-forlenger Smart-AVI
- AV-forlenger Advantech
- AV-forlenger Atlona
- AV-forlenger Crestron
- AV-forlenger Rocstor
- AV-forlenger Genexis
- AV-forlenger Techly
- AV-forlenger PureLink
- AV-forlenger ATen
- AV-forlenger Blustream
- AV-forlenger WyreStorm
- AV-forlenger C2G
- AV-forlenger Intelix
- AV-forlenger Comprehensive
- AV-forlenger Peerless-AV
- AV-forlenger HELGI
Nyeste AV-forlenger Manualer
9 Januar 2025
9 Januar 2025
9 Januar 2025
9 Januar 2025
9 Januar 2025
9 Januar 2025
9 Januar 2025
9 Januar 2025
9 Januar 2025
9 Januar 2025