Miiego MiiBLASTER GO Bruksanvisning

Miiego Hodetelefoner MiiBLASTER GO

Les nedenfor 📖 manual på norsk for Miiego MiiBLASTER GO (20 sider) i kategorien Hodetelefoner. Denne guiden var nyttig for 3 personer og ble vurdert med 4.5 stjerner i gjennomsnitt av 2 brukere

Side 1/20
Quick Start Guide
ENG
DK
NOR
SE
1 - 2
3 - 4
5 - 6
7 - 8 DE
9 - 10 FR
-
1
211
- 1413
- 1715
LN
EST
MiiBLASTER GO
WIRELESS SPEAKER
ENG
SPECIFICATIONS
CARE, MAINTENANCE, SAFETY
1
This device contains a lithium accumulator.
Improper use can cause erheating and fire. ov
Any modification of the product may have consequences for safety, warranty
and proper functioning. Keep out of reach for children and animals. Product
storage and working temperature: from -10 celsius degrees to +40. Do not
expose the product to direct sunlight, heat or naked flames as it may cause
damage or explosion. Do not use the product if a part is damaged or defective.
Replace a damaged or defective device immediately. Disconnect the product
from the electrical outlet and other equipment if problems occur. Do not
charge when the product is wet. Do not leave a battery on prolonged charge
when not in use. Do not dismantle, open or shred batteries. Do not drop the
product and avoid bumping. This product may only be serviced by a qualified
technician for maintenance to reduce the risk of electric shock etc.
Rechargeable 3.7V 3000 mAh Li-ion battery.
Full charging time: around 4-5 hours. IPX5.
BT frequency range: 2.402-2.480GHz. Freq. Response: 70Hz-16 KHz.
Charging input power: 5V DC/1A or 2A. RMS audio output: 20W. Impedance:
4 . Ω
5
6
7
9
8
1
2
3
4
button: Power On /Off. Pairing.
Mode (switch between BT, USB and
AUX-IN), Long press for TWS.
Light control button
EQ (BASS / ROCK / POP / CLASSIC)
Play / Pause
Volume down / Previous song
Volume up / Next song
Battery indicator - 4 LED lights
USB-in Port, Charging port, AUX IN
1
9
2 3 4 5 6 7 8
BACKSIDE
ENG
2
Pairing your MiiBLASTER GO MIIEGO® Wireless speaker
Charging the MiiBLASTER GO speaker
Next time charging
Turning Your MiiBLASTER GO On and Off
Play music from USB or AUX IN mode
Pairing and connecting 2 x MiiBLASTER GO speakers with TWS
1: Make sure the speaker is charged and turned OFF.
2: Press and hold the button for 2 seconds until the indicator light flashes
Blue (pairing mode).
3: Activate BT on your phone or other device and search for BT devices and
select: MiiBLASTER GO.
When MiiBLASTER GO is connected the Blue light is constantly on.
The speaker will remember your phone/device and automatically reconnect
the next time you turn it on.
An unpaired speaker will automatically turn off after 6 minutes.
Use a 5V/1A or 2A USB adapter for charging.
During charging the 4 LED battery indicator lights will flash one by one. When
fully charged the lights will stay on permanently.
Full charging time is around 4 hours with 2A and 5 hours with 1A.
When the first battery LED indicator light is flashing every 5 seconds, the
battery status is low and needs charging.
You will then also hear a battery warning tone every 120 seconds.
ON: Press and hold the Button for 2 seconds until a tone is heard.
OFF: Press the Button once and a tone is heard.
Insert USB flash or AUX audio cable on the back of the speaker (in AUX mode
switching songs on +/- buttons is unavailable).
TWS only works when connecting two MiiBLASTER GOs by MIIEGO together. ®
1: Turn on both speakers (BT mode). Make sure they are unconnected.
2: Press and hold on one speaker for 4 seconds. The product emits a button 2
tone to indicate entering TWS-pairing mode.
3: Activate BT on your audio source and connect with the product. The product
emits three tones and lights up to indicate successful TWS-pairing.button 2

Produkspesifikasjoner

Merke: Miiego
Kategori: Hodetelefoner
Modell: MiiBLASTER GO

Trenger du hjelp?

Hvis du trenger hjelp med Miiego MiiBLASTER GO still et spørsmål nedenfor, og andre brukere vil svare deg




Hodetelefoner Miiego Manualer

Hodetelefoner Manualer

Nyeste Hodetelefoner Manualer