Atdec AWM-W-S Bruksanvisning
Atdec
Flatpanelstøtte
AWM-W-S
Les nedenfor 📖 manual på norsk for Atdec AWM-W-S (2 sider) i kategorien Flatpanelstøtte. Denne guiden var nyttig for 3 personer og ble vurdert med 4.5 stjerner i gjennomsnitt av 2 brukere
Side 1/2
AWM-W Page 1 of 2
Installation Guide
AWM-W
AWM Single Wall Bracket
IMPORTANT INFORMATION
! Please ensure this product is installed as per these installation instructions.
! Do not remove or throw away the plastic sleeve on wall bracket.
! The manufacturer accepts no responsibility for incorrect installation.
! Failure to install this product correctly may cause serious injury/death during or following installation.
! This product is not suitable for outdoor use.
! Do not use this product for mobile applications.
! This product should only be installed by professional installers of good mechanical aptitude, who have experience with
building construction, and fully understand these instructions and the consequences of incorrect installation.
! Supplied wall fasteners are for timber stud wall constructions . For other wall constructions, such as masonry, alternative only
suitable wall fasteners should be sourced by the installer.
! To safely achieve the full capacity of this product, wall fasteners must have a pull-out (tension) force rating of at least 100kg
(1000N) per fastener. This rating must include a safety factor.
! Professional installer to ensure adequate structural capacity of wall (including appropriate safety factor) to support total
weight of all equipment being mounted.
! Drilling into electrical wires can cause death - use appropriate equipment and caution when drilling holes in walls to avoid
electrical cables, water pipes and gas pipes. Do not drill into structures unless you have established it’s safe to do so.
! Curved monitors, deep devices (such as all-in-one PCs), VESA mounted accessories (such as mini PC brackets and mounts),
and offset VESA locations exert additional leverage that can exceed the capacity of the mount even though the monitor
weight may be within the stated range. Please contact Atdec if you would like further information.
COMPONENT CHECKLIST
REQUIRED TOOLS
• Power drill
• Suitable drill bit
• Driver bit for selected wall fasteners
• Stud nder
• Spirit level
WEIGHT RANGE
0 - 18kg
(0 - 40lb)
Monitor weight should be within the weight range
of all modular elements that make up the complete
monitor mounting solution.
C
Washers
(x2)
B
M8x70mm
Screw
(x2)
D
6mm
Hex Key
(x1)
A
Single Wall Bracket
(x1)
AWM-W Page 2 of 2
1. Mount the Wall Bracket to the Wall
No portion of this document or any artwork contained herein should be reproduced in any way without
the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer
reserves the right to alter specications without notice. ©20230120B
x2
Using the
Single Wall
Bracket as
a template,
mark the
two xing
hole positions
for drilling.
NOTE: On a timber
stud wall, use a good
quality stud nder to
position mounting
fasteners in the
centre of studs.
NOTE: Wall bracket
must be level. Verify
using a quality spirit
level tool positioned
along the side edge
of the wall bracket.
2. (Optional) Set arm rotation to 360°
Note rotation is set to 180 by default. This will protect the wall by preventing the arm swinging into it.°
2.1. Remove plastic sleeve from
wall bracket
2.2. Remove rotation ring. 2.3. Place rotation ring in desired
position and replace plastic sleeve.
180°
360°
OR
Default
Position
Flipped
Position
3. Fit arm to Single Wall Bracket
3.2. Ensure arm is fully
pushed onto bracket.
3.1. Push arm onto
the wall bracket
shaft. Ensure grub
screw is retracted
before doing so.
3.3. Tighten the set screw
with 4mm Hex Key (supplied
with arm) to secure the arm
in place.
NOTE: Check the joint rotation
is smooth after tightening.
IMPORTANT:
Ensure plastic
sleeve is tted
on wall bracket.
NOTE:
• Alternative wall constructions,
such as masonry, will require
different fasteners than what is
supplied with the product.
• Selection and sourcing of
alternative wall mounting fasteners
is the responsibility of the installer.
See ‘Important Information’ above
for more details.
Timber Stud
NOTE: Thickness of sheeting and cladding
over the timber stud, including plaster
board, should not exceed 15mm ( ”).⅝
70mm (2 3
/4”)
Stud
(5
/
32”)
4mm
Produkspesifikasjoner
| Merke: | Atdec |
| Kategori: | Flatpanelstøtte |
| Modell: | AWM-W-S |
Trenger du hjelp?
Hvis du trenger hjelp med Atdec AWM-W-S still et spørsmål nedenfor, og andre brukere vil svare deg
Flatpanelstøtte Atdec Manualer
8 Desember 2024
8 Desember 2024
8 Desember 2024
8 Desember 2024
8 Desember 2024
8 Desember 2024
8 Desember 2024
8 Desember 2024
8 Desember 2024
Flatpanelstøtte Manualer
- Flatpanelstøtte Schwaiger
- Flatpanelstøtte Kogan
- Flatpanelstøtte My Wall
- Flatpanelstøtte Dell
- Flatpanelstøtte Blaupunkt
- Flatpanelstøtte Speaka
- Flatpanelstøtte Chief
- Flatpanelstøtte V7
- Flatpanelstøtte Rocstor
- Flatpanelstøtte Mount-It!
- Flatpanelstøtte Proaim
- Flatpanelstøtte CTA Digital
- Flatpanelstøtte Avteq
- Flatpanelstøtte Heckler
- Flatpanelstøtte GPX
- Flatpanelstøtte Peerless-AV
- Flatpanelstøtte Multibrackets
- Flatpanelstøtte SunBriteTV
- Flatpanelstøtte Gabor
Nyeste Flatpanelstøtte Manualer
11 Desember 2024
11 Desember 2024
10 Desember 2024
10 Desember 2024
8 Desember 2024
8 Desember 2024
8 Desember 2024
8 Desember 2024
8 Desember 2024
7 Desember 2024