Atlona PND110 Bruksanvisning

Les nedenfor 📖 manual på norsk for Atlona PND110 (4 sider) i kategorien Ikke kategorisert. Denne guiden var nyttig for 3 personer og ble vurdert med 4.5 stjerner i gjennomsnitt av 2 brukere

Side 1/4
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2018 PN624
Page 1 of 4
Table Top Box, Tilt Up
Part Number(s): PND110
Parts Included:
(1) Table Top Box
(1) Plate
(1) Mini-Com Faceplate
(1) NetKey Faceplate
(2) Mounting Brackets
(4) Mounting Screws
(2) Table Securing Screws
(2) Wing Nuts
(2) Cable Clamps & Screws
(1) Fastener Tool
PRINT UNSCALED AT 100%
Installation Precautions
For best results, place the Table Top Box, Tilt Up
in a dry area away from dust.
To prevent fire or shock, do not expose this unit to
water or moisture. Do not place the unit in direct
sunlight, near heaters or heat-radiating
appliances, or near any liquid. Exposure to direct
sunlight, smoke, or steam can harm internal
components.
Handle carefully; dropping or jarring can damage
the bezel.
Never place fingers inside the opening on either
side of the unit. This action could cause injury due
to sharp edges inside.
Do not place heavy objects on top of the Table
Top Box, Tilt Up. Do not use excessive force to
push down on the top of the unit.
Disconnect the power cord to turn off the power.
This supplies power to the socket on the pop up
panel. The power outlet should be installed near
the equipment and be easily accessible.
We recommend using wall outlets with a Ground
Fault Circuit Interrupter (GFCI) for maximum
protection.
Install all cables according to the instructions
found herein. Do not force or pull any cable that is
attached to the Table Top Box, Tilt Up.
Cleaning
Surfaces should be cleaned with a dry cloth. Never use
strong detergents or solvents such as alcohol or
thinner. Do not use a wet cloth or water to clean the
unit.
Operation
The Table Top Box, Tilt Up will open easily when the
top is pressed down and then released.
When the Table Top Box, Tilt Up is not in use, simply
press the top down until it is level with the surface of
the table and then release. The unit will remain hidden
until needed again.
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2018 PN624
Page 2 of 4
Mounting Screws
Plate
Faceplate
(NetKey or
Mini-com)
Modules
(Recommended
angled wire cap)
Note:
Modules in these
two positions have
limited clearance
(Recommended
angled wire cap)
Table Top Box,
Tilt Up
Use cut-out
template on
(page 4)
PRINT UNSCALED AT 100%
For Technical Support: www.panduit.com/resources/install_maintain.asp
INSTALLATION INSTRUCTIONS
© Panduit Corp. 2018 PN624
Page 3 of 4
Operator
Interface Tabletop
Min. thickness 0.5" [1.27cm]
Max. thickness 3.5" [8.89cm]
Table securing
screws (2)
Wing Nuts (2)
Mounting
Brackets (2)
PRINT UNSCALED AT 100%

Produkspesifikasjoner

Merke: Atlona
Kategori: Ikke kategorisert
Modell: PND110

Trenger du hjelp?

Hvis du trenger hjelp med Atlona PND110 still et spørsmål nedenfor, og andre brukere vil svare deg




Ikke kategorisert Atlona Manualer

Ikke kategorisert Manualer

Nyeste Ikke kategorisert Manualer