Aube TH106 Bruksanvisning

Aube Termostat TH106

Les nedenfor 📖 manual på norsk for Aube TH106 (3 sider) i kategorien Termostat. Denne guiden var nyttig for 4 personer og ble vurdert med 4.5 stjerner i gjennomsnitt av 2 brukere

Last ned PDF

Side 1/3

TH106 400-106-001-D 12/8/05 1/3

This programmable thermostat can be used to control an electric

heating system such as an electric baseboard heater, a radiant ceil-

ing, a radiant floor, a convector, etc.

The thermostat cannot be used under the following conditions:

• The resistive load is greater than 16.7 A

• The resistive load is less than 2 A

• The system is driven by a contactor or relay (inductive load)

• The system is a central heating system

SUPPLIED PARTS:

• One (1) thermostat

• Two (2) 6-32 screws

• Two (2) solderless connectors

TURN OFF POWER TO THE HEATING SYSTEM AT THE MAIN

POWER PANEL TO AVOID ELECTRICAL SHOCK.

THE INSTALLATION MUST BE PERFORMED BY AN ELECTRI-

CIAN.

 All cables and connections must conform to the local electrical

code.

 Special CO/ALR solderless connectors must be used when con-

necting with aluminum conductors.

 Install the thermostat onto an electrical box.

 Install the thermostat about 5 feet high, on an inside wall facing

the heater.

 Avoid locations where there are air drafts (such as the top of a

staircase or an air outlet), dead air spots (such as behind a

door), or direct sunlight.

 Do not install the thermostat on a wall that conceals chimney or

stove pipes.

 The thermostat wires are not polarized; either wire can be con-

nected to the load or to the power supply.

NOTE: Always keep the thermostat's vents clean and unobstructed.

oConnect the thermostat wires to the line wires and to the load

wires using solderless connectors for copper wires.

pPush any excess wire back into the electrical box.

NOTE: If necessary, before re-installing the front component, config-

ure the thermostat (see section 3).

qReturn power to heating system.

nn 1.

oo 2.

Select the

operating mode

Set the time

Time and day

Temperature

Operating

mode icons

Skip a period

Program the

schedule Temperature

preset icons

Temperature

adjustment

buttons

Temperature

preset buttons

Heating power

indicator

Periods

Appears when the

setpoint is displayed

Set the day

2-wire installation

4-wire installation

TH106 400-106-001-D 12/8/05 2/3

The configuration switches are on the back of

the thermostat. The factory settings are indi-

cated by the gray cells in the following table.

Upon power-up, the thermostat is in manual mode ( ) and displays

the actual (ambient) temperature.

nPress the Hour and Min buttons to set the thermostat’s clock.

oPress the Day button to set the day.

Setpoint

The thermostat normally displays the actual temperature. To view the

setpoint, press the or button briefly. The setpoint will appear for

the next 5 seconds.

To change the setpoint, press the or button until the desired

temperature is displayed. To scroll faster, hold the button.

Using a preset temperature

The thermostat has 3 preset temperatures:

 Comfort temperature

 Economy temperature

 Vacation temperature

• To use the Comfort or Economy temperature, press the or

button respectively. The corresponding icon will be displayed.

• To use the Vacation temperature, press both and buttons

simultaneously. The icon will be displayed.

Storing a preset temperature

To store the Comfort or Economy temperature:

Set the desired temperature using the or button. Press and

hold the appropriate button ( or ) for approximately 3 sec-

onds until the corresponding icon is displayed. Press the Mode

button.

To store the Vacation temperature:

Set the desired temperature using the or button. Press and

hold both and buttons simultaneously for approximately 3

seconds until the icon is displayed. Press the Mode button.

Automatic - The temperature is set according to the programmed

schedule. To place the thermostat in this mode, press Mode until

is displayed. The icons of the current period and preset temperature

are also displayed.

Temporary Bypass: If you modify the setpoint (by pressing the

, , or button) when the thermostat is in automatic

mode, the new setpoint will be used until the end of the current

period. When the next period starts, the temperature set for that

period becomes the new setpoint.

Manual - The programmed schedule is not used. The temperature

must be set manually. To place the thermostat in this mode:

nPress Mode until is displayed.

oSet the temperature using the , , or button.

The schedule consists of 4 periods per day which represents a typi-

cal weekday. You can program the thermostat to skip the periods that

do not apply to your situation. For example, you can skip periods 2

and 3 for the weekend.

The Comfort ( ) temperature is used in periods 1 and 3 and the

Economy ( ) temperature is used in periods 2 and 4. For example,

when the period changes from 1 to 2, the setpoint automatically

changes from Comfort setting ( ) to Economy setting ( ).

You can have a different program for each day of the week; i.e., each

period can start at different time for each day of the week. The

thermostat has been programmed with the following schedule.

To modify the schedule:

nPress Pgm to access the programming mode. Period 1 is

selected.

oPress Day to select the day to program (hold for 3 seconds to

select the entire week).

pPress Hour and Min to set the start time of the selected period,

or press Clear if you want to skip the period (--:-- is displayed).

qPress Pgm to select another period, or press Day to select

another day. Then repeat step 3.

SW1 Early Start a

a. Early Start can be used in Automatic mode only. When this func-

tion is enabled, the thermostat calculates the optimal time to start

heating in order to obtain the desired temperature by the set time.

The thermostat re-assesses the start time daily based on the pre-

vious day’s performance.

Off On

SW2 Temperature / time format b

b. If you change the temperature display format, the preset

temperatures ( , and ) will return to their default settings.

°C / 24-hour °F / 12-hour

SW3 Cycle length c

c. 15-second cycles should be selected in most cases as it provides

better temperature control. 15-minute cycles must be selected if

you have a fan-equipped heater or if 15-second cycles causes

light flickering (especially in rural regions).

15 seconds 15 minutes

SW4 Not used - -

qq 4.

rr 5.

Icon Intended use Factory setting

Comfort (when at home) 21°C (70°F)

Economy (when asleep or away from home) 16.5°C (62°F)

Vacation (during prolonged absence) 10°C (50°F)

ss 6.

tt 7.

Period Description Associated temperature preset

Wake

Leave

Return

Sleep

Period Setting MO TU WE TH FR SA SU

6:00

8:00

AM --:-- --:--

6:00

PM --:-- --:--

10:00

TH106 400-106-001-D 12/8/05 3/3

rPress Mode to exit the programming mode.

NOTE: If no button is pressed for 60 seconds, the thermostat will

automatically exit the programming mode.

During a power outage, the settings are stored in memory. However,

only the thermostat’s clock must be re-adjusted if the power failure

lasts more than 2 hours. When power comes back, the thermostat

will return to the operating mode that was active prior to the power

failure.

Power: 120/240 VAC, 50/60 Hz

Minimum load: 2 A (resistive only)

500 W @ 240 VAC

250 W @ 120 VAC

Maximum load: 16.7 A (resistive only)

2000 W @ 120 VAC

4000 W @ 240 VAC

Display range: 0°C to 60°C (32°F to 140°F)

Display resolution: 0.5°C (1°F)

Setpoint range: 5°C to 30°C (40°F to 86°F)

Setpoint interval: 0.5°C (1°F)

Storage: -20°C to 50°C (-4°F to 120°F)

Approval: c UL us

Aube warrants this product, excluding battery, to be free from defects

in the workmanship or materials, under normal use and service, for a

period of three (3) years from the date of purchase by the consumer.

If at any time during the warranty period the product is determined to

be defective or malfunctions, Aube shall repair or replace it (at Aube's

option).

If the product is defective,

(i) return it, with a bill of sale or other dated proof of purchase, to

the place from which you purchased it, or

(ii) contact Aube. Aube will make the determination whether the

product should be returned, or whether a replacement product can

be sent to you.

This warranty does not cover removal or reinstallation costs. This

warranty shall not apply if it is shown by Aube that the defect or mal-

function was caused by damage which occurred while the product

was in the possession of a consumer.

Aube's sole responsibility shall be to repair or replace the product

within the terms stated above. AUBE SHALL NOT BE LIABLE FOR

ANY LOSS OR DAMAGE OF ANY KIND, INCLUDING ANY INCI-

DENTAL OR CONSEQUENTIAL DAMAGES RESULTING,

DIRECTLY OR INDIRECTLY, FROM ANY BREACH OF ANY WAR-

RANTY, EXPRESS OR IMPLIED, OR ANY OTHER FAILURE OF

THIS PRODUCT. Some provinces and states do not allow the exclu-

sion or limitation of incidental or consequential damages, so this limi-

tation may not apply to you.

THIS WARRANTY IS THE ONLY EXPRESS WARRANTY AUBE

MAKES ON THIS PRODUCT. THE DURATION OF ANY IMPLIED

WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANT-

ABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IS

HEREBY LIMITED TO THE THREE-YEAR DURATION OF THIS

WARRANTY. Some provinces and states do not allow limitations on

how long an implied warranty lasts, so the above limitation may not

apply to you.

This warranty gives you specific legal rights, and you may have other

rights which vary from province or state to another.

If you have any questions about the product installation or operation,

or concerning the warranty, contact us at:

705 Montrichard

Saint-Jean-sur-Richelieu, Quebec

J2X 5K8

Canada

Tel.: (450) 358-4600

Toll-free: 1-800-831-AUBE

Fax: (450) 358-4650

Email: aube.service@honeywell.com

For more information on our products, go to

www.aubetech.com

uu 8.

vv 9.

PROBLEM SOLUTIONS

Thermostat is hot.

This condition is normal. Under normal

operation, the thermostat housing can

reach a temperature between 35°C (95°F)

and 40°C (104°F).

Heater is always On. The thermostat has not been correctly

wired.

Thermostat indicates

that heating is On, but

the heater is not On.

The thermostat has not been correctly

wired.

Wrong temperature is

displayed.

The thermostat is exposed to air draft.

Eliminate the draft.

The sticker on the thermostat’s screen has

not been removed.

Wrong time is displayed. The thermostat was without power for

more than 2 hours.

Temperature does not

change according to the

programmed schedule.

Check that the thermostat is in Automatic

mode. Check the schedule and clock set-

tings.

Display disappears and

reappears after a few

minutes.

The thermal protection device on the

heater is open. This can happen after a

power failure or if the heater is obstructed

by furniture or curtains.

Display looks faded

when heating is acti-

vated

The heating system is less than the

required minimum load. This thermostat

cannot be used below that rating.

ww 10.

;

11.

12.

As an ENERGY STAR® partner, Aube Technologies has

determined that this product meets the E NERGY STAR

guidelines for energy efficiency.

Produkspesifikasjoner

Merke:	Aube
Kategori:	Termostat
Modell:	TH106

Trenger du hjelp?

Hvis du trenger hjelp med Aube TH106 still et spørsmål nedenfor, og andre brukere vil svare deg

Ditt navn*

Din e-post*

Skriv spørsmålet ditt her

Termostat Aube Manualer

Aube TH115 AF Bruksanvisning

27 Oktober 2024

Aube TH106 Bruksanvisning

18 Oktober 2024

Termostat Manualer

Nyeste Termostat Manualer

Vemer Keo-B Bruksanvisning

27 Oktober 2024

King K101 Bruksanvisning

27 Oktober 2024

Vemer Thalos Key Bruksanvisning

27 Oktober 2024

Fantini Cosmi 1598089 Bruksanvisning

27 Oktober 2024

Honeywell CT87K1004/U1 Bruksanvisning

27 Oktober 2024

Danfoss RET1000 MS Bruksanvisning

27 Oktober 2024

Honeywell TH4110B1009/U Bruksanvisning

27 Oktober 2024

Niko 88001 Bruksanvisning

27 Oktober 2024

Niko 88000 Bruksanvisning

27 Oktober 2024

Honeywell Round Clock Deluxe T8725M Bruksanvisning

27 Oktober 2024