Chief SLM230 Bruksanvisning
Chief
Tilbehør til projektor
SLM230
Les nedenfor 📖 manual på norsk for Chief SLM230 (1 sider) i kategorien Tilbehør til projektor. Denne guiden var nyttig for 6 personer og ble vurdert med 4.5 stjerner i gjennomsnitt av 2 brukere
Side 1/1
I N S T A L L A T I O N I N S T R U C T I O N S
CSAV, Inc., and its affiliated corporations and subsidiaries (collectively, "CSAV"), intend to make this manual accurate and complete. However, CSAV makes no claim that the infor-
mation contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product. The
information contained in this document is subject to change without notice or obligation of any kind. CSAV makes no representation of warranty, expressed or implied, regarding the
information contained herein. CSAV assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
© 2007 Chief Manufacturing, 8401 Eagle Creek Parkway, Savage, MN 55378
• P: 800.582.6480 / 952.894.6280 • F:877.894.6918 / 952.894.6918
8802-002035
8/31/07
SLB-230 and SLM-230 Interface Brackets
for Mitsubishi VPL-XD200U, VPL-SD200U, VPL-XD300U, VPL-XD350U,
SLB and SLM series Interface brackets are designed for use with Chief RPA, RPM, and Smart-Lift series projector mounts. See the specific
installation instructions provided with the mount for additional installation information.
Unpack carton and verify kit contents. If any listed parts are missing, immediately contact a Chief Customer Service representative by calling
1-800-582-6480.
WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer!
Installation:
WARNING: OVERTIGHTENING OF SCREWS CAN DAMAGE PARTS AND LEAD TO SERIOUS PERSONAL INJURY AND DAMAGE
TO EQUPIMENT! DO NOT over tighten screws when installing interface brackets.
NOTE: Step 1 is only required when installing an SLB Interface bracket. If an SLM bracket is being installed proceed to step 2.
1. Screw four thumb screws onto four 10-24 x 5/8" Philips pan head screws. DO NOT fully tighten thumb screws at this time.
2. Turn projector upside down on a flat surface.
3. Place the interface bracket on to the bottom of the projector lining up the three mounting holes in the interface bracket with the three
threaded inserts in the bottom of the projector and secure using the three M4 -8mm mounting screws and M4 Flatwashers.
NOTE: Security screws can be substituted when mounting Interface bracket to projector by using the parts and installation instructions in the
All-Points Security Kit.
(1) Interface Bracket (3) Washer, Flat, M4
(4) 10-24 Thumb Nuts ** (3) SCREW, Pan head, M4 x 8mm
(1) All-Points Security Kit
**Only used when installing SLB Interface brackets.
SLB-230 SLM-230
Produkspesifikasjoner
| Merke: | Chief |
| Kategori: | Tilbehør til projektor |
| Modell: | SLM230 |
Trenger du hjelp?
Hvis du trenger hjelp med Chief SLM230 still et spørsmål nedenfor, og andre brukere vil svare deg
Tilbehør til projektor Chief Manualer
1 Januar 2025
1 Januar 2025
1 Januar 2025
1 Januar 2025
1 Januar 2025
1 Januar 2025
1 Januar 2025
1 Januar 2025
1 Januar 2025
1 Januar 2025
Tilbehør til projektor Manualer
- Tilbehør til projektor Sony
- Tilbehør til projektor My Wall
- Tilbehør til projektor Panasonic
- Tilbehør til projektor Unicol
- Tilbehør til projektor Auna
- Tilbehør til projektor Speaka
- Tilbehør til projektor Roadinger
- Tilbehør til projektor Vogels
- Tilbehør til projektor Peerless-AV
- Tilbehør til projektor NeoMounts
- Tilbehør til projektor SMK-Link
- Tilbehør til projektor Konig & Meyer
Nyeste Tilbehør til projektor Manualer
21 Februar 2025
16 Januar 2025
16 Januar 2025
16 Januar 2025
16 Januar 2025
15 Januar 2025
15 Januar 2025
14 Januar 2025
14 Januar 2025
10 Januar 2025