Elba ETM-E3690P Bruksanvisning
Les nedenfor 📖 manual på norsk for Elba ETM-E3690P (1 sider) i kategorien Kran. Denne guiden var nyttig for 2 personer og ble vurdert med 4.5 stjerner i gjennomsnitt av 2 brukere
Side 1/1
ETM-E3690P
1. An opening hole of 35mm diameter is required on sink top or work top (C) for installation of tap.
2. Slide the rubber O-ring (B) up to the base of tap (A).
3.Screw the flex hoses (H) up to the extension tube, then insert the tap through the hole of sink top or
worktop (C), and position the tap properly.
4.Slide the plastic fitting I (D) through the extension tube ,then slide the plastic fitting II (E) through the
sprayer hose and up to the plastic fitting I(D).
Important: ensure the opening of plastic fitting I (D) is close to threaded tube , and the sprayer hose
runs freely through the plastic fitting II (E).
5.Put the permanent seat(F) through the threaded tube , and tighten the fixing washer(G) securely.
Important: make sure the hose runs smoothly before tightened the fixing washer.
6.Connect the flex hoses (H) to the hot & cold water supply, and the sprayer hose to the threaded tube.
7. Adjusting the pull-out length of sprayer hose and fasten the weighing ball (I) with screws.
●Before installation, please ensure that the following
work conditions are adhered to:
-Water temperature between 0 C - 90 C˚ ˚
-Water pressure between 0.05MPa – 1.0MPa. Pressure
reducing valve is necessary if pressure exceeds 1.2MPa
-Avoid major pressure di erences between hot and cold ff
water supply
●Flush pipes thoroughly before and after installation to
ensure water supply is free of any debris.
●Inspect tap fitting and debugged to its best. Do not
attempt to disassemble fitting on your own.
●Use thread sealant tape (PTFE) on any screw joining
connections and ensure all joints are securely tightened.
A Tap body
B Rubber O ring
C Sink top or work
top
D Plastic fitting I
E Plastic fitting Ⅱ
F Permanent seat
G Fix ing washer
H Flex hose
I Weighing ball
J Rubber washer
for flexi hose
This . FIAMMA SDN. BHD. will not be held responsible for the use of superseded or voided specifications.
Fabricatoe must check for cut-out accuracy.
specification is subject to change without notice
Stainless Steel Mixer Tap
Produkspesifikasjoner
| Merke: | Elba |
| Kategori: | Kran |
| Modell: | ETM-E3690P |
Trenger du hjelp?
Hvis du trenger hjelp med Elba ETM-E3690P still et spørsmål nedenfor, og andre brukere vil svare deg
Kran Elba Manualer
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024
Kran Manualer
- Kran IKEA
- Kran Caple
- Kran Franke
- Kran Karran
- Kran Delta
- Kran Concept
- Kran Moen
- Kran Hansgrohe
- Kran Grohe
- Kran Livarno Lux
- Kran Zip
- Kran Oliveri
- Kran Blanco
- Kran ProFlo
- Kran Rohl
- Kran Pfister
- Kran Symmons
- Kran Jacuzzi
- Kran Puretec
- Kran Omnires
- Kran American Standard
- Kran Billi
- Kran Gessi
Nyeste Kran Manualer
16 Januar 2025
16 Januar 2025
12 Januar 2025
12 Januar 2025
12 Januar 2025
12 Januar 2025
12 Januar 2025
12 Januar 2025
12 Januar 2025
12 Januar 2025