EMOS P5760 Bruksanvisning
EMOS
Ringeklokke
P5760
Les nedenfor 📖 manual på norsk for EMOS P5760 (74 sider) i kategorien Ringeklokke. Denne guiden var nyttig for 2 personer og ble vurdert med 4.5 stjerner i gjennomsnitt av 2 brukere
Side 1/74
3402060000_31-P5760_00_01_WEB 80 × 120 mm
www.emos.eu
P5760
GB Wireless Doorchime & Repeater
CZ Bezdrátový zvonek & prodlužovač signálu
SK Bezdrôtový zvonček & predlžovač signálu
PL Dzwonek bezprzewodowy & repeater sygnału
HU Vezeték nélküli csengő és jelismétlő
SI Brezžični zvonec in ojačevalnik signala
RS|HR|BA|ME Bežično kućno zvono i repetitor
DE Drahtlose Klingel und Signalverlängerung
UA Бездротовий дзвоник & подовжувач сигналу
RO|MD Sonerie fără r & prelungitor de semnal
LT Belaidis durų skambutis ir retransliatorius
LV Bezvadu durvju zvans un atkārtotājs
EE Juhtmevaba uksekell ja repiiter
BG Безжичен звънец и повторител
FR Carillon sans l & prolongateur de portée
IT Campanello senza li & ripetitore di segnale
ES Timbre inalámbrico & repetidor de señal
NL Draadloze deurbel & signaalverlenger
2
1
25
6
3
4
A B C
1
2
3
GB | Wireless Doorchime & Repeater
The set consists of a doorchime button (transmitter) and a chime (receiver). The chime is deigned for constant
connection to a 230 V AC/50 Hz power network. The transmission between the button and the chime is done
via radio waves at a frequency of 433.92 MHz. The range depends on local conditions and reaches up to 120 m
in open spaces without interference.
The set has a so-called „self-learning“ function – the button is able to generate its own pairing code which is
then received by the chime and stored in its memory. The set can thus be expanded with additional buttons.
Their „self-learning“ function also prevents them from aecting neighbouring doorchimes.
The range of the button can be extended using the „repeater“ function (signal repeater).
For proper usage of the wireless doorchime, read the instruction manual thoroughly.
Technical Specications
Transmission range: up to 120 m in an open area (can drop down to one fth in a busy area)
Button: water resistant; enclosure IP44
3
Pairing of chime and buttons: „self-learning“ function
Pairing capacity: maximum of 8 buttons per 1 chime
Number of ringtones: 16
Transmission frequency: 433.92 MHz, 5 mW e.r.p. max.
Chime power supply: 230 V AC/50 Hz
Button power supply: 1× 3 V battery (type CR2032, included)
USB connector: output max. 5 V, 2 A
Includes: double-sided adhesive tape, screws
Chime Description (see Fig. 1)
1 – chime LED
2 – ringing mode button
3 – volume settings button
4 – repeater button (signal repeating)
5 – speaker
6 – USB connector (used for charging compatible devices, see Technical Specications).
Button Description (see Fig. 2)
A – battery
B – button for changing ringtone/erasing memory of paired buttons
C – ring button/LED
Opening the Rear Compartment of the Button (see Fig. 3)
Pairing the Button with the Chime
1. Remove the rear cover of the button with a screwdriver through the hole on the side (see Fig. 3).
Insert a 3 V battery, type CR2032, into the button. When inserting the battery, make sure to observe correct
polarity (+ polarity up)!
2. Plug the chime into a 230 V AC/50 Hz socket. You will hear a „ding dong“ tone.
The chime automatically switches to „self-learning“ mode which lasts for 60 second.
3. During these 60 seconds, press the button you want to pair with the chime. If the chime receives signal
from the button, a tone will sound, the button will pair with the chime and the self-learning mode will
automatically end.
4. For pairing multiple buttons, repeat steps 1 to 3.
Note: Before pairing each button, the chime must be put into self-learning mode – unplug and plug into
a 230 V socket.
You can pair a maximum of 8 buttons per chime this way.
Note: The chime has an internal memory where it stores the codes of the currently paired buttons for cases of
power failure. Once power supply to the chime is restored, the chime will automatically enter self-learning mode
for 60 seconds. However, if no signal is received within these 60 seconds (new pairing is not performed), the
chime will automatically load the codes of the previously paired buttons after self-learning mode ends. There
is thus no need to pair buttons again after a power failure.
Wiping the Memory of Paired Buttons
Remove the rear cover of the button with a screwdriver through the hole on the side.
1. Set the chime to pairing mode – unplug the chime from the socket and replug it again; a tone will sound.
Produkspesifikasjoner
| Merke: | EMOS |
| Kategori: | Ringeklokke |
| Modell: | P5760 |
Trenger du hjelp?
Hvis du trenger hjelp med EMOS P5760 still et spørsmål nedenfor, og andre brukere vil svare deg
Ringeklokke EMOS Manualer
14 Desember 2024
14 Desember 2024
14 Desember 2024
14 Desember 2024
14 Desember 2024
14 Desember 2024
14 Desember 2024
14 Desember 2024
14 Desember 2024
14 Desember 2024
Ringeklokke Manualer
- Ringeklokke Arendo
- Ringeklokke Kogan
- Ringeklokke Eufy
- Ringeklokke Lorex
- Ringeklokke Delta
- Ringeklokke Bearware
- Ringeklokke Cata
- Ringeklokke Arlo
- Ringeklokke Imou
- Ringeklokke Ring
- Ringeklokke Elektrobock
- Ringeklokke Vimar
- Ringeklokke Extel
- Ringeklokke NuTone
- Ringeklokke EQ-3
Nyeste Ringeklokke Manualer
17 Desember 2024
16 Desember 2024
16 Desember 2024
16 Desember 2024
12 Desember 2024
24 Oktober 2024
24 Oktober 2024
24 Oktober 2024
24 Oktober 2024
24 Oktober 2024