Glide Gear POV100 Bruksanvisning
Glide Gear
Stativ
POV100
Les nedenfor 📖 manual på norsk for Glide Gear POV100 (3 sider) i kategorien Stativ. Denne guiden var nyttig for 2 personer og ble vurdert med 4.5 stjerner i gjennomsnitt av 2 brukere
Side 1/3
POV 100
1 PLEASE NOTE:
For use with cameras weighing up to 2.5lbs or
1.15kg including the lens
The POV100 comes in 2 sizes: M (54 60cm/21.25- -
23.6”) and L (56 62cm/22 24.4- - ”)
Recommended use with wide angle lenses set to
innity focus for best results
For more informaon please visit our website: www.glidegear.net
2
Fig A
4
Mount your camera using the screw
inside the slot in the crossbar in the
front of the helmet. See Fig A.
Crossbar
Mounng
screw
3 Included with the POV 100 are 10 weight plates. With
the camera mounted in the front, your head will be
leaning forward. Add weight plates to the back of the
helmet to balance your head and ease the strain on
your neck. Use the supplied thumb nut to secure the
weight plates in an unloose posion. See Fig. B
Fig C
Hint: Weigh your camera and use the appropriate
number of plates to get as close as possible to the
camera weight knowing that 1 plate weighs about
4oz (or 100g).
Example: For a camera weighing 1.6lbs, add 6-7
plates to the back.
Thumb nut
In the rear inside of the helmet, you will nd a knob.
Use the knob to ghten or loosen the helmet s inside ’
frame so that the helmet ts ghtly on your head.
The knob in queson is circled on Fig. C.
Fig B
POV 100
5
Top Plate features:
1/4 20 female threaded holes to mount mic, lights, fricon arm etc..-
14/4 20 mounng screw to mount a GoPro, a 360 camera, light, mic, fricon -
arm etc..
For more informaon please visit our website: www.glidegear.net
Fig D
At this point, your setup should look like Fig. D. The POV 100 is a very exible head rig with mulple
adjustments and mounng possibilies. See the adjustments available below .
Front Plate features:
1/4 20 female threaded holes -
for accessories
14/4 20 mounng screw-
Crossbar Knobs:
Loosen up the knobs. Adjust the
angle of the camera. Tighten the
knobs when done.
Temple Plate:
Remove the 2 screws. While
keeping a 45 degree angle, move
the camera frame horizontally
and along the slot to adjust how
far from the face the camera will
be.
Lock in place using the 2 screws.
Use the other threaded holes to
mount accessories.
Mid –secon Knobs:
Loosen up the knobs. Adjust
the camera posion so you
can see clearly in front of
you. Tighten the knobs when
done.
POV 100
For more informaon please visit our website: www.glidegear.net
If any assembling is needed, please refer to the below secon:
BACK: Mount the plate with the longest
screw to the back of the helmet using 2 of the
supplied M3 screws. Fig E.
FRONT: Mount the curved rectangular plate
to the front of the helmet using 2 of the sup-
plied M3 screws and through the 2 slots on
the plate. Fig F.
SIDES: Mount the 2 idencal plates to the sides
of the helmet using 2 of the supplied M3 screws
and through the 2 slots on the plate. Each plate
should be oriented so that the plate s thicker end ’
faces the back of the helmet . Fig. H.
TOP: Mount the rectangular at plate to the
top of the helmet using 2 of the supplied M3
screws and through the 2 slots on the plate.
Fig G.
Thinner end
Thicker end
Fig F
Fig E
Fig G
Fig H
Produkspesifikasjoner
| Merke: | Glide Gear |
| Kategori: | Stativ |
| Modell: | POV100 |
Trenger du hjelp?
Hvis du trenger hjelp med Glide Gear POV100 still et spørsmål nedenfor, og andre brukere vil svare deg
Stativ Glide Gear Manualer
17 Oktober 2024
16 Oktober 2024
Stativ Manualer
- Stativ Neewer
- Stativ Kogan
- Stativ Vello
- Stativ Manfrotto
- Stativ Kodak
- Stativ Square Jellyfish
- Stativ Proaim
- Stativ Libec
- Stativ Gravity
- Stativ Celestron
- Stativ Vanguard
- Stativ Vinten
- Stativ ARRI
- Stativ Fidlock
- Stativ Vortex
- Stativ Robus
- Stativ Miller
- Stativ Studio Assets
- Stativ Easyrig
- Stativ Magnus
- Stativ Peak Design
- Stativ Hohem
- Stativ Flycam
Nyeste Stativ Manualer
28 Oktober 2024
28 Oktober 2024
28 Oktober 2024
27 Oktober 2024
27 Oktober 2024
27 Oktober 2024
27 Oktober 2024
27 Oktober 2024
27 Oktober 2024
27 Oktober 2024