Hinkley Lighting Carlton 4771SL Bruksanvisning
Hinkley Lighting
Lettelse
Carlton 4771SL
Les nedenfor 📖 manual på norsk for Hinkley Lighting Carlton 4771SL (3 sider) i kategorien Lettelse. Denne guiden var nyttig for 3 personer og ble vurdert med 4.5 stjerner i gjennomsnitt av 2 brukere
Side 1/3
assembly instructions
Item No. 4771
1. Find a clear area in which you can work.
2. Unpack fixture and glass from carton.
3. Carefully review instructions prior to assembly.
*** The construction of this fixture will be accomplished by first assembling the
main body of the fixture, making all necessary electrical connections, hanging
the fixture from the ceiling, and then installing the shade and crystals.
4771
SAFETY WARNING: READ WIRING AND GROUNDING INSTRUCTIONS (I.S. 18)
AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPLY OFF DURING
INSTALLATION. IF NEW WIRING IS REQUIRED, CONSULT A QUALIFIED
ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS.
Drawing 2 - Fixture Assembly
01.01.13
1. Rotate arms until they are approximately degrees apart - see(A) 90 Drawing 1
and 3.
2. Fixture can be installed at this time.
A A
A
A
90º
Drawing 1 - Fixture Assembly
s r reta t he
33000 Pin Oak P ark w ay, Avon Lak e , OH 4 4 0 1 2 800.446.5 5 3 9 / 440.653.5 5 0 0 h i n k leyl ighting.com
Drawing 3 - Fixture Mounting
Drawing 2 - Strap Detail
J
B
AG
D
E
C
1. Prepare mounting strap for mounting by installing screws into mounting (B) (A)
plate - see .(B) Drawing 2
• Be sure the holes into which the screws are threaded match the spacing of holes (C)
in the canopy - see .(1) Drawings 2 and 3
2. Attach mounting plate to junction box , using screws provided and slip (B) (J) (G)
supply wires through large center hole.
Make electrical connections from supply wire to fixture lead wires. Refer to instruction
sheet and follow all instructions to make all necessary wiring connections. (I.S. 18)
Then return back to this sheet to continue installation of this fixture.
5
51. Hang the fixture by slipping canopy over screws and hold in position - see (D) (B)
Drawings 2 and 3.
2. Thread ball knobs onto end of screws and tighten to secure fixture to ceiling.(E) (B)
61. To install shade , slip shade over fixture installed fixture body and place tab (1) (T)
on top of crossbar and align holes in tab with holes in crossbar -see .(S) Drawing 4
2. Slip screw through holes in tab and crossbar and thread on ball knob to (2) (3)
secure shade to fixture.
3. See page 2 of instruction for crystal installation.
page 1
12
3
assembly instructions
Item No. 4771
4771
s r reta t he page 2
1. Find a clear area in which you can work.
2. Unpack fixture and glass from carton.
3. Carefully review instructions prior to assembly.
01.01.13
1. To complete assembly, first thread bottom finial with crystal attached onto (3) (F)
bottom of fixture - see .Drawing 2
2. Proceed to attach crystals using as a reference quide. If a crystal must Drawing 2
be replaced, please use the part no.s provided below the crystal drawings when
ordering.
3. The crystals are referenced with the quantity ( Ex. ? x 6) required following the
letter.
R4771CRY-C R4771CRY-BR4771CRY-A
B CA
R4772CRY-C
D
CRYSTAL INDENTIFICATION
A X 4
A X 4
A X 4 B X 4
C X 4
D ATTACHED
TO FINIAL
33000 P in Oak P ark w ay Avon Lake, OH 44012 8 0 0 .4 4 6 .5 5 3 9 / 4 4 0 .6 5 3 .5 5 0 0 hinkl eyli g h t ing.com
I.S. 18 wiring grounding instructions
SAFETY WARNING: READ WIRING AND GROUNDING INSTRUCTIONS (I.S. 18)
AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPLY OFF DURING
INSTALLATION. IF NEW WIRING IS REQUIRED, CONSULT A QUALIFIED
ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS.
wiring instructions
Indoor Fixtures
1. Connect positive supply wire (A) (typically black or the smooth, unmarked
side of the two-conductor cord) to positive fixture lead with appropriately (B)
sized twist on connector - see .Drawings 1 or 2
2. Connect negative supply wire (typically white or the ribbed, marked (C)
side of the two-conductor cord) to negative fixture lead .(D)
3. Please refer to the below to complete all grounding instructions
electrical connections.
Outdoor Fixtures
1. Connect positive supply wire (A) (typically black or the smooth unmarked
side of the two-conductor cord) to positive fixture lead with appropriately (B)
sized twist on connector - see . Drawings 2 or 3
2. Connect negative supply wire (typically white or the ribbed, marked (C)
side of the two-conductor cord) to negative fixture lead .(D)
3. Cover open end of connectors with silicone sealant to form a watertight seal.
• If installing a wall mount fixture, use caulk to seal gaps between the fixture
mounting plate (backplate) and the wall. This will help prevent water from
entering the outlet box. If the wall surface is lap siding, use caulk and a
fixture mounting platform specially.
4. Please refer to the below to complete all grounding instructions
electrical connections.
grounding instructions
Flush Mount Fixtures
For positive grounding in a 3-wire electrical system, fasten the fixture ground
wire (typically copper or green plastic coated) to the fixture mounting strap (E) (1)
with the ground screw - see . (2) Drawing 1
Note: On straps for screw supported fixtures, first install the two mounting screws in strap.
Any remaining tapped hole may be used for the ground screw.
Chain Hung Fixtures
Loop fixture ground wire (typically copper or green plastic coated) under the (E)
head of the ground screw on fixture mounting strap and connect to the (2) (1)
loose end of the fixture ground wire directly to the ground wire of the building
system with appropriately sized twist-on connectors - see .Drawing 2
Post-Mount Fixtures
Connect fixture ground wire (typically copper or green plastic coated) to power (E)
supply ground with appropriately sized twist-on connector inside post. Cover open
end of connector with silicone sealant to form a watertight seal - see .Drawing 3
Drawing 1 - Flush Mount
Drawing 2 - Chain Hung
supply wire
fixture leads
twist-on
connectors
Drawing 3 - Post-Mount
twist-on
connectors
1
A CC
B D
supply wire
fixture leads
A C
B D
1
2
supply wire
fixture leads
A C
B D
twist-on
connectors
E
2
E
E
E
E
I.S. 18
Produkspesifikasjoner
| Merke: | Hinkley Lighting |
| Kategori: | Lettelse |
| Modell: | Carlton 4771SL |
Trenger du hjelp?
Hvis du trenger hjelp med Hinkley Lighting Carlton 4771SL still et spørsmål nedenfor, og andre brukere vil svare deg
Lettelse Hinkley Lighting Manualer
5 Januar 2025
5 Januar 2025
5 Januar 2025
5 Januar 2025
5 Januar 2025
5 Januar 2025
5 Januar 2025
5 Januar 2025
5 Januar 2025
5 Januar 2025
Lettelse Manualer
- Lettelse DeWalt
- Lettelse Hama
- Lettelse Neewer
- Lettelse Hazet
- Lettelse Philips
- Lettelse Schwaiger
- Lettelse IKEA
- Lettelse TP Link
- Lettelse Kogan
- Lettelse GoGEN
- Lettelse Nitecore
- Lettelse Kichler
- Lettelse Integral LED
- Lettelse ET2
- Lettelse Quoizel
- Lettelse Crystorama
- Lettelse Brennenstuhl
- Lettelse Varaluz
- Lettelse FIAP
- Lettelse Aputure
- Lettelse Media-tech
- Lettelse Gemini
- Lettelse Klein Tools
- Lettelse Schneider
- Lettelse Dainolite
- Lettelse Tesy
- Lettelse Martin
- Lettelse EMOS
- Lettelse Sharper Image
- Lettelse Fluval
- Lettelse Ryobi
- Lettelse Nanlite
- Lettelse BeamZ
- Lettelse Maxim
- Lettelse Brandson
- Lettelse Aplic
- Lettelse CSL
- Lettelse Bearware
- Lettelse NUVO
- Lettelse Milwaukee
- Lettelse OttLite
- Lettelse Be Cool
- Lettelse Showtec
- Lettelse Busch + Müller
- Lettelse V-Tac
- Lettelse Infinity
- Lettelse Nedis
- Lettelse Elation
- Lettelse Chauvet
- Lettelse Weeylite
- Lettelse Black Diamond
- Lettelse ESYLUX
- Lettelse Livarno Lux
- Lettelse Casalux
- Lettelse Aqara
- Lettelse Beghelli
- Lettelse Middle Atlantic
- Lettelse Rosco
- Lettelse DeSisti
- Lettelse Astera
- Lettelse EXO
- Lettelse Profoto
- Lettelse GRE
- Lettelse Ikan
- Lettelse Ring
- Lettelse Olight
- Lettelse Perel
- Lettelse Blackburn
- Lettelse Sigma
- Lettelse Rayzr 7
- Lettelse Excello
- Lettelse Vimar
- Lettelse Genaray
- Lettelse Altman
- Lettelse Setti+
- Lettelse Kanlux
- Lettelse ARRI
- Lettelse Osram
- Lettelse Light4Me
- Lettelse GlobalTronics
- Lettelse Lume Cube
- Lettelse Digipower
- Lettelse ETC
- Lettelse Fiilex
- Lettelse Portman
- Lettelse ColorKey
- Lettelse Litepanels
- Lettelse Perfect Christmans
- Lettelse XQ-Lite
- Lettelse Govee
- Lettelse Peerless-AV
- Lettelse Heitronic
- Lettelse Obsidian
- Lettelse Blizzard
- Lettelse LUPO
- Lettelse Enttec
- Lettelse Fotodiox
- Lettelse GVM
- Lettelse Amaran
- Lettelse Halo
- Lettelse HQ Power
- Lettelse Kino Flo
- Lettelse Cateye
- Lettelse Maxxmee
- Lettelse Angler
- Lettelse Raya
- Lettelse Elan
- Lettelse Livex Lighting
- Lettelse Ranex
- Lettelse Fuzzix
- Lettelse COLBOR
- Lettelse Lucide
- Lettelse DIO
- Lettelse Paulmann
- Lettelse Melinera
- Lettelse Yongnuo
- Lettelse Audibax
- Lettelse Hudson Valley
- Lettelse Forte Lighting
- Lettelse Smith-Victor
- Lettelse Zylight
- Lettelse Cineo
- Lettelse Prolycht
- Lettelse AD Trend
Nyeste Lettelse Manualer
16 Januar 2025
16 Januar 2025
16 Januar 2025
16 Januar 2025
16 Januar 2025
16 Januar 2025
15 Januar 2025
15 Januar 2025
14 Januar 2025
14 Januar 2025