Hinkley Lighting Harper 3641BK-CS Bruksanvisning

Hinkley Lighting Lettelse Harper 3641BK-CS

Les nedenfor 📖 manual på norsk for Hinkley Lighting Harper 3641BK-CS (2 sider) i kategorien Lettelse. Denne guiden var nyttig for 4 personer og ble vurdert med 4.5 stjerner i gjennomsnitt av 2 brukere

Side 1/2
assembly instructions
Item No. 3641
1. Find a clear area in which you can work.
2. Unpack fixture and glass from carton.
3. Carefully review instructions prior to assembly.
*** The construction of this fixture will be accomplished by first attaching the
mounting strap to the junction box, making all necessary electrical connections,
hanging the fixture from the ceiling, and then installing the glass.
start here
3641
Drawing 4 - Fixture Assembly
Make electrical connections from supply wire to fixture lead wires. Refer to instruction
sheet and follow all instructions to make all necessary wiring connections. (I.S. 18)
Then refer back to this sheet to continue installation of this fixture.
***It is recommended you have some assistance when installing the glass on this
fixture.
1. Main body of fixture can be mounted to the ceiling and lamped accordingly prior (1)
to installing the glass. Remove knurled knob (4) from arms prior to installing the
glass - see Drawing 4 .
2. Slip glass into ring . (3) (2)
3. Lift ring with glass and slip inside uprights and align holes in ring studs(2) (3) (U) (H)
(S) (T) (U) (4) with holes in uprights and thread in knurled knobs to secure glass to
fixture.
SAFETY WARNING: READ WIRING AND GROUNDING INSTRUCTIONS (I.S. 18)
AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPLY OFF DURING
INSTALLATION. IF NEW WIRING IS REQUIRED, CONSULT A QUALIFIED
ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS.
01.01.13
Drawing 3 - Fixture Mounting
Drawing 2 - Strap Detail
J
B
AG
D
E
C
1. Prepare mounting strap for mounting by installing screws into mounting (B) (A)
plate - see .(B) Drawing 1
Be sure the holes into which the screws are threaded match the spacing of holes (C)
in the canopy - see .(1) Drawings 2 and 3
2. Attach mounting plate to junction box , using screws not provided and slip (B) (J) (G)
supply wires through large center hole.
2. Hang the fixture by slipping canopy over screws (D) (A) and hold in position - see
Drawings 2 and 3.
3. Thread barrel knobs (E) onto end of screws (A) and tighten to secure fixture to ceiling.
1
3
4
2
H I N K L E Y L I G H T I N G 3300 0 Pin Oak Park way Avon L ake , O H 440 12 80 0.4 46 .55 39 / 44 0.6 53 .55 00 hi nk le yl igh tin g.com
U
S
H
T
Drawing 1 - Strap Detail
120o
1. First rotate arms attached to canopy until they are degrees apart - see Drawing 1.120
r2-12
T24 JA8-2016
I.S. 18 wiring grounding instructions
SAFETY WARNING: READ WIRING AND GROUNDING INSTRUCTIONS (I.S. 18)
AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPLY OFF DURING
INSTALLATION. IF NEW WIRING IS REQUIRED, CONSULT A QUALIFIED
ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS.
wiring instructions
Indoor Fixtures
1. Connect positive supply wire (A) (typically black or the smooth, unmarked
side of the two-conductor cord) to positive fixture lead with appropriately (B)
sized twist on connector - see .Drawings 1 or 2
2. Connect negative supply wire (typically white or the ribbed, marked (C)
side of the two-conductor cord) to negative fixture lead .(D)
3. Please refer to the below to complete all grounding instructions
electrical connections.
Outdoor Fixtures
1. Connect positive supply wire (A) (typically black or the smooth unmarked
side of the two-conductor cord) to positive fixture lead with appropriately (B)
sized twist on connector - see . Drawings 2 or 3
2. Connect negative supply wire (typically white or the ribbed, marked (C)
side of the two-conductor cord) to negative fixture lead .(D)
3. Cover open end of connectors with silicone sealant to form a watertight seal.
If installing a wall mount fixture, use caulk to seal gaps between the fixture
mounting plate (backplate) and the wall. This will help prevent water from
entering the outlet box. If the wall surface is lap siding, use caulk and a
fixture mounting platform specially.
4. Please refer to the below to complete all grounding instructions
electrical connections.
grounding instructions
Flush Mount Fixtures
For positive grounding in a 3-wire electrical system, fasten the fixture ground
wire (typically copper or green plastic coated) to the fixture mounting strap (E) (1)
with the ground screw - see . (2) Drawing 1
Note: On straps for screw supported fixtures, first install the two mounting screws in strap.
Any remaining tapped hole may be used for the ground screw.
Chain Hung Fixtures
Loop fixture ground wire (typically copper or green plastic coated) under the (E)
head of the ground screw on fixture mounting strap and connect to the (2) (1)
loose end of the fixture ground wire directly to the ground wire of the building
system with appropriately sized twist-on connectors - see .Drawing 2
Post-Mount Fixtures
Connect fixture ground wire (typically copper or green plastic coated) to power (E)
supply ground with appropriately sized twist-on connector inside post. Cover open
end of connector with silicone sealant to form a watertight seal - see .Drawing 3
Drawing 1 - Flush Mount
Drawing 2 - Chain Hung
supply wire
fixture leads
twist-on
connectors
Drawing 3 - Post-Mount
twist-on
connectors
1
A CC
B D
supply wire
fixture leads
A C
B D
1
2
supply wire
fixture leads
A C
B D
twist-on
connectors
E
2
E
E
E
E
I.S. 18
H I N K L E Y L I G H T I N G 33000 Pin Oak Parkway Avon Lake, OH 44012 800.446.5539 / 440.653.5500 hinkleylighting.com

Produkspesifikasjoner

Merke: Hinkley Lighting
Kategori: Lettelse
Modell: Harper 3641BK-CS

Trenger du hjelp?

Hvis du trenger hjelp med Hinkley Lighting Harper 3641BK-CS still et spørsmål nedenfor, og andre brukere vil svare deg




Lettelse Hinkley Lighting Manualer

Lettelse Manualer

Nyeste Lettelse Manualer