Induction Dynamics C2 Bruksanvisning

Les nedenfor 📖 manual på norsk for Induction Dynamics C2 (4 sider) i kategorien Høyttaler. Denne guiden var nyttig for 3 personer og ble vurdert med 4.5 stjerner i gjennomsnitt av 2 brukere

Side 1/4
H
A
N
D
C
R
A
F
T
E
D
I
N
A
M
E
R
I
C
A
H
A
N
D
C
R
A
F
T
E
D
I
N
A
M
E
R
I
C
A
FREESTANDING SPEAKERS
OWNERS MANUAL
Rev 07.01.2019
urin Exceence Manufacturin Exceence
Man
nce
Manufacturin Exceence
Manufacturin Ex
Exceence
Manufacturin Exceence
Manufact
Manufacturin Exceence
Manufacturin Excee
Manufacturin Exceence
Manufacturin Exceence
urin Exceence
Manufacturin Exceence
Man
nce
Manufacturin Exceence
Manufacturin Ex
Exceence
Manufacturin Exceence
Manufact
FREESTANDING SPEAKERS
Please read the following instructions carefully before installing your Induction Dynamics ® freestanding speakers. If you have
any questions regarding installation that are not answered in the following directions, please contact your local sound contractor
or the Induction Dynamics®/MSE Audio® technical support team. Contact information can be found on the back of the manual.
General Information
Your speakers and amplier come in a high quality nish that is both attractive and durable. To clean, use a soft, damp cloth. If
your drivers become dusty, dust them with a paintbrush or a brush vacuum attachment. Do not use a strong or abrasive cleaner.
The grille is covered in acoustic cloth. To keep your grille clear of debris, we recommend you use a lint roller (like you would use
on clothes).
Do not use bass or loudness contour controls. Induction Dynamics’ subwoofers produce very low frequencies without these
controls. Use of these controls will make the bass sound “boomy”, obscure higher frequencies, and possibly cause damage
due to excessive cone excursion.
Amplifer location: The A2 amplier is best located in an equipment rack or shelving with other audio and video equipment. It is
not recommended for placement behind walls or other limited access locations, where service may be restricted.
Carpet spikes are not required for these speakers. However, they have been provided if you would prefer to use them. Should
you choose to do so, lay the speaker on its back side, then screw the carpet spikes into the threaded holes under the base of
each speaker.
Speaker Wiring: Use approved wire designed for in-wall or exposed use, as appropriate for your installation. For freestanding
speakers, we recommend using high-quality speaker wire that is 12 gauge or lower, with easily visible polarity coding to make
your connections. The following chart identies minimum gauge requirements for various lengths. See your local dealer or
installation contractor for more information.
Length in Feet
Up to 18’
Up to 29’
Up to 51’
AWG Size & Stranding
14 Gauge (19/27)
12 Gauge (65/30)
10 Gauge (105/30)
Wire Length / Minimum Gauge
Requirements
Subwoofer Connection
The jumpers should be removed and the switch set to “Three-way + Subwoofer”. Connect the lower binding posts on the back
of the ID1 or ID1.15 to the A2 subwoofer amplier in series using reverse polarity (red to black and black to red). Below are
diagrams showing alternative methods of connecting the subwoofers, to achieve the in-series, reverse-polarity connections.
Power Connection
Connect the A2 amplier to a 120 volt, single phase, 60 Hz, grounded power supply using the power cord provided. For best
results, use a dedicated power circuit for your amplication equipment.

Produkspesifikasjoner

Merke: Induction Dynamics
Kategori: Høyttaler
Modell: C2

Trenger du hjelp?

Hvis du trenger hjelp med Induction Dynamics C2 still et spørsmål nedenfor, og andre brukere vil svare deg




Høyttaler Induction Dynamics Manualer

Høyttaler Manualer

Nyeste Høyttaler Manualer