Khind WH903P Bruksanvisning
Khind
Kjeler & kjeler
WH903P
Les nedenfor 📖 manual på norsk for Khind WH903P (13 sider) i kategorien Kjeler & kjeler. Denne guiden var nyttig for 3 personer og ble vurdert med 4.5 stjerner i gjennomsnitt av 2 brukere
Side 1/13
model / 型号 WH803 & WH903P
P/N: 40-50582-00
Water Heater / / 电热水器 Pemanas Air
Instruction Manual / Buku Panduan说明指示书 /
Please read this manual carefully before operating this product. Keep this manual handy for further reference.
请在使用此产品前,详读此说明书。并将之收藏以作日后参考。
Sila baca buku panduan ini dengan teliti sebelum menggunakan produk ini. Simpanlah untuk rujukan masa depan.
Important / / Mustahak重要
This manual is also available online.
www.khind.com.my
3
Model
Voltage
Heater Power
Pump Type
Pump Power rating
Noise Level
Water Connection
Operating Connection
Protection Against Electric Shock
Degree of Protection
Minimum Water Flow Rate
Minimum Water Pressure
Maximum Water Pressure
Product Dimension (WxLxH)
Net Weight (kg)
WH803
240V~ 50/60Hz
3.75kW
-
-
-
15mm (1/2" BSP),
Single Point System
Open Outlet
Class I
IP25
3 Litres / minute
20 kPa (0.2 bar/ 2.9 psi)
0.3 Mpa (3bar/43.5psi)
340x240x95mm
1.8kg
WH903P
240V~ 50/60Hz
3.75kW
DC Pump
50W
<40dB
15mm (1/2" BSP),
Single Point System
Open Outlet
Class I
IP25
3 Litres / minute
20 kPa (0.2 bar/ 2.9 psi)
0.3 Mpa (3bar/43.5psi)
340x240x95mm
2.5kg
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
Specifications
*Specifications are subject to change without prior notice.
Schematic diagram
2
Parts identification
1. Power ON Indicator
2. ELSD ON Indicator
3. Power/Temperature Control Knob
4. ELSD Test Button
5. ELSD Reset Button
6. Shower Head
7. Shower Rail
8. Shower Hose
9. Filter Valve
10. Flow Regulator Valve
11. Pump ON/OFF Button (for WH903P only)
12. Pump Indicator (for WH903P only)
a. 2-in-1 Manual Reset Thermal-cut-out
& Thermostat
b. Thermistor
c. Heater Tank
d. PCB (Indicator)
e. PCB (ELSD)
f. PCB (Push Button & Control)
g. Flow Switch
h. Triac
i. Cable Clip
j. Terminal Block
k. Pump (for WH903P)
External Parts Identification
Internal Parts Identification
WH803 WH903P
WH803 WH903P
1
a
b
c
d
e
f
2
3
4
5
1
2
3
4
5
11
g
h
j
i
a
b
c
d
e
f
g
h
j
i
k
12
6
7
8
9
10
WH903P (DC Pump)WH803
Cleaning & maintenance
Clean filters regularly
Remove the Regulator Valve Insert from the regulator valve assembly. Take out the
Filter Plate Unit as shown and flush it with water to remove any trapped particle. Slot
back the Filter Plate Unit to its original position and secure it.
Adjustment of Regulator Valve
Turn the knob clockwise to have the maximum water volume in low water pressure
areas. In high water pressure areas, turn the knob anticlockwise until the desired
shower temperature is attained.
General Maintenance
• DO NOT use thinner, alcohol or petrol.
Clean the heater with a damp cloth and mild detergent but do not use thinner, alcohol, petrol or any other
organic solution.
• Shower head must be periodically clean to ensure no blockage occurred.
• Check and clean the filter mesh inside the regulator valve regulary.
This is continuous-flow instantaneous water heater. Flow-controlled and designed to withstand the full main
pressure, and the continuous flow instantaneous water heater will supply hot water whenever you need it.
The main features of our continuous flow water heaters are:
• High energy conversion efficiency
• Small size
• Point-of use installation for single tap connection
General product information
1. Please read this manual thoroughly and understand the content before use.
2. Check if the main supply voltage is matched with the voltage stated on the rating plate of the water heater.
3. Installation of water heater must be carried out by an authorised or qualifed technician.
4. DO NOT attempt to repair the water heater without qualified technician.
5. DO NOT switch on the water heater if there is a possibility that the water in the heater is frozen.
6. DO NOT install INLET & OUTLET of water heater reversely.
7. DO NOT install the water heater where there is consistent spray directly over the unit.
8. DO NOT connect the OUTLET to any tap or fitting that is not recommended by the manufacturer.
9. DO NOT block the water heater outer in any way.
10. The spray head (shower head) must be descaled regularly.
11. To ensure perfect functioning of the heater, certain minimum water flow level must be guaranteed
(Refer Product Specification).
12. Separate electric circuits must be provided for the water heater.
13. Test water temperature with hand before using the the water heater. Be careful to avoid scalding by hot
water.
14. Check the ELSB once a month and consult professional for repair if there is any malfunction.
15. Metallic/chromed flexible hose and conductive control valve shall not be used.
16. This appliance is not intended for use by persons (including children)
with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision
concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the
appliance.
17. DO NOT leave the hand shower idle in the pail.
18. Do not use plumbing cement on connection. If necessary, use only
thread or sealing tape.
19. This appliance must be earthed.
20. This appliance is intended for household use only. Not for commercial use
or outdoor use.
21. It is forbidden to place flammable and explosive materials near the water heater.
22. Please install the water heater on a secure and solid wall.
Safety precaution
54
Installation
General Installation Instructions
1. Installation must be carried out by a qualified electrician with close reference to the operation manual and
in compliance with the local regulations.
2. The water heater must only be installed and operated in a room free from frost.
3. The screws and wall plugs required for mounting the water heater are included in the delivery.
Note: The control knob(s) are integral part of the cover, do not attempt to remove them.
4. Mark mounting position
• Unscrew the bottom retained screw and lift the cover from the back plate.
• Use the back plate as the template and mark the three fixing holes.
• Drill the holes and insert the wall plugs.
• Insert the cables through the cable entry of the water heater.
• Fit the water heater to the secure solid wall.
Heater INLET and OUTLET Connection
1. All the plumbing works should be completed
before proceeding to electrical wiring connection.
2. INLET and OUTLET connection of the heater
unit should not be reversed, with Flow
Regulator Valve Assembly installed on INLET.
!CAUTION:
THIS APPLIANCE MUST BE EARTHED.
OUTLET INLET
Flow Regulator Valve Assembly
installed on INLET
Bottom View
Produkspesifikasjoner
| Merke: | Khind |
| Kategori: | Kjeler & kjeler |
| Modell: | WH903P |
Trenger du hjelp?
Hvis du trenger hjelp med Khind WH903P still et spørsmål nedenfor, og andre brukere vil svare deg
Kjeler & kjeler Khind Manualer
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024
16 Oktober 2024
Kjeler & kjeler Manualer
- Kjeler & kjeler Bosch
- Kjeler & kjeler Imarflex
- Kjeler & kjeler Tesy
- Kjeler & kjeler Daikin
- Kjeler & kjeler Remeha
- Kjeler & kjeler Kunft
- Kjeler & kjeler Mora
- Kjeler & kjeler HTW
- Kjeler & kjeler Kospel
- Kjeler & kjeler AquaTech
Nyeste Kjeler & kjeler Manualer
24 Oktober 2024
24 Oktober 2024
23 Oktober 2024
23 Oktober 2024
23 Oktober 2024
23 Oktober 2024
23 Oktober 2024
23 Oktober 2024
23 Oktober 2024
23 Oktober 2024