Kicker KXA800.5 Bruksanvisning

Kicker Mottaker KXA800.5

Les nedenfor 📖 manual på norsk for Kicker KXA800.5 (48 sider) i kategorien Mottaker. Denne guiden var nyttig for 2 personer og ble vurdert med 4.5 stjerner i gjennomsnitt av 2 brukere

Side 1/48
KXA800.5
Manual del Propietario | Español
AMPLIFICADOR DEL LA SERIE KX.5
Benutzerhandbuch | Deutsch
VERSTÄRKER DER KX.5-SERIE
Manuel d’utilisation | Française
AMPLIFICATEUR DE SÉRIE KX.5
KX
AMPLIFIERS
Owner’s Manual
2017 KXA 5ch Amps Rev H.indd 1
2017 KXA 5ch Amps Rev H.indd 1
2017 KXA 5ch Amps Rev H.indd 1
2017 KXA 5ch Amps Rev H.indd 1
2017 KXA 5ch Amps Rev H.indd 1 4/25/2017 1:08:39 PM
4/25/2017 1:08:39 PM
4/25/2017 1:08:39 PM
4/25/2017 1:08:39 PM
4/25/2017 1:08:39 PM
2
KX.5-SERIES AMPLIFIERS
OWNER’S MANUAL
INSTALLATION
Mounting: Choose a structurally sound location to mount your KICKER amplifi er. Make sure there are no
items behind the area where the screws will be driven. Choose a location that allows at least 4(10cm)
of open ventilation for the amplifi er. If possible, mount the amplifi er in the climate-controlled passenger
compartment. Drill four holes using a 7/64” (3mm) bit and use the supplied #8 screws to mount the
ampli er.
Wiring: Disconnect the vehicles battery to avoid an electrical short. Then, connect the ground wire to the
ampli er. Make the ground wire short, 24” (60cm) or less, and connect it to a paint-and-corrosion-free,
solid, metal area of the vehicles chassis. Adding an additional ground wire of this same gauge (or larger)
between the battery’s negative post and the vehicle chassis is recommended.
PERFORMANCE
MODEL: KXA800.5
IMPORTANT SAFETY WARNING
PROLONGED CONTINUOUS OPERATION OF AN AMPLIFIER, SPEAKER, OR SUBWOOFER IN
A DISTORTED, CLIPPED OR OVER-POWERED MANNER CAN CAUSE YOUR AUDIO SYSTEM
TO OVERHEAT, POSSIBLY CATCHING FIRE AND RESULTING IN SERIOUS DAMAGE TO YOUR
COMPONENTS AND/OR VEHICLE. AMPLIFIERS REQUIRE UP TO 4 INCHES (10CM) OPEN
VENTILATION. SUBWOOFERS SHOULD BE MOUNTED WITH AT LEAST 1 INCH (2.5CM)
CLEARANCE BETWEEN THE FRONT OF THE SPEAKER AND ANY SURFACE.
Model: KXA800.5
RMS Power, and AMP1 AMP2
@ 14.4V, stereo, 1% THD+N
@ 14.4V, stereo, 1% THD+N
@ 14.4V, mono, 1% THD+N
50W x 4
100W x 4
200W x 2
RMS Power, channelSUB
@ 14.4V, mono, 1.5 % THD+N
@ 14.4V, mono, 1.5 % THD+N
400W x 1
200W x 1
Length [in, cm] 12-3/4, 32.4
Height [in, cm] 2-1/8, 5.5
Width [in, cm] 8-5/16, 21
Frequency Response [Hz] 10Hz–20kHzAMPS 1-2:
SUB: 10Hz–160Hz
Signal-to-Noise Ratio [dB] >95dB, A-weighted, re: rated power
Input Sensitivity 250mV–10V
Selectable Electronic Crossover OFF/HP/LP, variable 10–5,000Hz with 10X switch; AMP 1:
24dB/octave
AMP 2: OFF/HP/LP/BP, variable HP 10–500Hz,
variable LP 40–5,000Hz with 10X switch; 24dB/octave
SUB: Variable LP 10–160Hz; 24dB/octave
KickEQ™ Boost - Variable 0-18db; Center Frequency - 40Hz
Subsonic Filter Variable 10–80Hz; 24dB/Octave
NOTE: 2017 KX amplifi er subwoofer channels are 1Ω stable - power rating equivalent to operation, +/- 10%
2017 KXA 5ch Amps Rev H.indd 2
2017 KXA 5ch Amps Rev H.indd 2
2017 KXA 5ch Amps Rev H.indd 2
2017 KXA 5ch Amps Rev H.indd 2
2017 KXA 5ch Amps Rev H.indd 2 4/25/2017 1:08:46 PM
4/25/2017 1:08:46 PM
4/25/2017 1:08:46 PM
4/25/2017 1:08:46 PM
4/25/2017 1:08:46 PM
3
Install a fuse within 18” (45cm) of the battery and in-line with the power cable connected to your amplifi er.
If you ever need to remove the amplifi er from the vehicle after it has been installed, the ground wire should
be the last wire disconnected from the amplifi er--just the opposite as when you installed it.
POWER WIRING
source unit
high-level speaker
outputs
to amplifi er
shield
+
core conductor KICKER KISL (optional)
from source unit high-
level speaker outputs
OR
to amplifi er
Model External Fuse
(sold separately)
Power/Ground Wire KICKER Wiring Kit
KXA800.5 1 x 100 Ampere 4 Gauge PK4, CK4
12V
RADIO
DETECT
battery
external fuse
remote turn-on
(see page 6)
bare-metal
chassis ground
bare-metal
chassis ground
≤18
(45cm)
≤24
(60cm)
The KX ampli er’s RCA inputs will receive either high or low level signals from your car stereos source
unit. A high-level signal can be run from the source unit’s speaker outputs to the stereo RCA input on the
end panel of the amplifi er using the KICKER KISL as shown. Alternatively, the signal can be delivered to
the amplifi er using the low-level RCA outputs on the source unit. Keep the audio signal cable away from
factory wiring harnesses and other power wiring. If you need to cross this wiring, cross it at a 90 degree
angle.
2017 KXA 5ch Amps Rev H.indd 3
2017 KXA 5ch Amps Rev H.indd 3
2017 KXA 5ch Amps Rev H.indd 3
2017 KXA 5ch Amps Rev H.indd 3
2017 KXA 5ch Amps Rev H.indd 3 4/25/2017 1:08:46 PM
4/25/2017 1:08:46 PM
4/25/2017 1:08:46 PM
4/25/2017 1:08:46 PM
4/25/2017 1:08:46 PM

Produkspesifikasjoner

Merke: Kicker
Kategori: Mottaker
Modell: KXA800.5

Trenger du hjelp?

Hvis du trenger hjelp med Kicker KXA800.5 still et spørsmål nedenfor, og andre brukere vil svare deg




Mottaker Kicker Manualer

Mottaker Manualer

Nyeste Mottaker Manualer