Kicker PXA500.1 Bruksanvisning

Kicker Mottaker PXA500.1

Les nedenfor 📖 manual på norsk for Kicker PXA500.1 (20 sider) i kategorien Mottaker. Denne guiden var nyttig for 10 personer og ble vurdert med 4.5 stjerner i gjennomsnitt av 2 brukere

Last ned PDF

Side 1/20

PXA MONO AMPLIFIERS

PXA200.1 | PXA500.1

Owner’s Manual | English

Manual del Propietario | Español

AMPLIFICADOR DEL LA SERIE PXA.1

Benutzerhandbuch | Deutsch

MONOVERSTÄRKER DER PXA.1-SERIE

Manuel d’utilisation | Française

AMPLIFICATEUR DE SÉRIE PXA.1

PXA Ampliﬁers

2015 PXA Mono Amplifiers Rev F.indd 1

2015 PXA Mono Amplifiers Rev F.indd 1 10/23/2015 2:31:41 PM

10/23/2015 2:31:41 PM

PXA.1-SERIES AMPLIFIERS

OWNER’S MANUAL

INSTALLATION

Mounting: Choose a structurally sound location to mount your KICKER ampliﬁ er. Make sure there are no items

behind the area where the screws will be driven. Choose a location that allows at least 4” (10cm) of open

ventilation for the ampliﬁ er. Drill four holes using a 7/64” (3mm) bit and use the supplied #8 screws to mount the

ampliﬁ er.

Wiring: Disconnect the vehicle’s battery to avoid an electrical short. Then, connect the PXA harness to the

ampliﬁ er. A good ground connections is important. If this ampliﬁ er is mounted in the front fairing of a motorcycle, it

will be best to extend the ground wire all the way to the battery.

The PXA ampliﬁ ers have the capability to receive almost any level of input signal. If a Hi-Level signal is coming

from the speaker leads of the source unit, simply cut off the RCA jacks and connect it directly to the exposed

wires. Set the Input Level switch to Hi. Set the Auto Turn-On to DC. If speaker leads are not available from your

source unit, use an RCA stereo cable to connect directly to the RCA connectors of the PXA ampliﬁ er. Set the

Input Level switch to Lo. Set the Auto Turn-On switch to +12V, and use the blue remote trigger wire to turn the

ampliﬁ er on.

PERFORMANCE

Authorized KICKER Dealer:

Purchase Date:

Serial Number:

Model: PXA200.1 PXA500.1

RMS Power [Watts]

@ 14.4V, 4Ω mono, ≤ 1% THD+N

@ 14.4V, 2Ω mono, ≤ 1% THD+N

@ 14.4V, 1 mono, ≤ 1% THD+N

@ 14.4V, 0.5 mono, ≤ 1% THD+N

25 x 1

50 x 1

100 x 1

200 x 1

250 x 1

500 x 1

N/A

Length [in, cm] 4-3/4, 12 8-1/4, 21

Height [in, cm] 1-9/16, 4 1-9/16, 4

Width [in, cm] 3-7/16, 8.7 3-7/16, 8.7

Frequency Response [Hz] 25 - 120 25 - 120

Signal-to-Noise Ratio [dB] 95 95

Input Sensitivity Low Level: 125mV–5V

High Level: 250mV–10V

Low Level: 125mV–5V

High Level: 250mV–10V

Electronic Crossover Selectable 60Hz, 80Hz, 100Hz or

120Hz low pass; 24dB/octave slope

Selectable 60Hz, 80Hz, 100Hz or

120Hz low pass; 24dB/octave slope

KickEQ™ Bass Boost Selectable 0 or +6dB @ 40Hz Selectable 0 or +6dB @ 40Hz

Subsonic Filter 25Hz, 24dB/octave slope 25Hz, 24dB/octave slope

Remote Bass Yes Yes

Pro Tip: To get the best performance from your new KICKER Ampliﬁ er and extend the warranty by 1 year, use

genuine KICKER accessories and wiring.

MODEL: PXA200.1 | PXA500.1

IMPORTANT SAFETY WARNING –

PROLONGED CONTINUOUS OPERATION OF

AN AMPLIFIER IN A DISTORTED OR CLIPPED

MANNER CAN CAUSE YOUR AUDIO SYSTEM

TO OVERHEAT, POSSIBLY CATCHING FIRE

AND RESULTING IN SERIOUS DAMAGE TO

YOUR COMPONENTS AND/OR VEHICLE.

2015 PXA Mono Amplifiers Rev F.indd 2

2015 PXA Mono Amplifiers Rev F.indd 2 10/23/2015 2:31:51 PM

10/23/2015 2:31:51 PM

12V

Model External Fuse

PXA200.1 1 x 15 Ampere

PXA500.1 1 x 45 Ampere

battery

external fuse

(15A)

external fuse

(45A)

remote

turn-on

remote turn-on

speaker outputs

RCA inputs

(remove to use

hi-level input)

bare-metal chassis ground

bare-metal

chassis

ground

insert power and

ground terminal

adapter

bare-metal

chassis ground

≤18”

(45cm)

≤18”

(45cm)

≤24”

(60cm)

≤24”

(60cm)

Cut the looped red power cable located on the PXA harness and install a 15A (PXA200.1) or 45A (PXA500.1)

fuse. Fuse installation should be within 18” (45cm) of the battery and in-line with the harness’ power cable, which

is connected to your ampliﬁ er. If you ever need to remove the ampliﬁ er from the vehicle after it has been installed,

the ground wire should be the last wire disconnected from the ampliﬁ er--just the opposite as when you installed it.

PXA200.1

PXA500.1

KICKER KISL (optional)

from source unit high-level speaker outputs

to ampliﬁ er

PXA500.1: Use 8 gauge wire if the

power wire is greater than 10 feet in

length; 10 gauge if less.

2015 PXA Mono Amplifiers Rev F.indd 3

2015 PXA Mono Amplifiers Rev F.indd 3 10/23/2015 2:31:51 PM

10/23/2015 2:31:51 PM

Produkspesifikasjoner

Merke:	Kicker
Kategori:	Mottaker
Modell:	PXA500.1

Trenger du hjelp?

Hvis du trenger hjelp med Kicker PXA500.1 still et spørsmål nedenfor, og andre brukere vil svare deg

Ditt navn*

Din e-post*

Skriv spørsmålet ditt her

Mottaker Kicker Manualer

Kicker 44KXARC Bruksanvisning

16 Oktober 2024

Kicker CX800.1 Bruksanvisning

16 Oktober 2024

Kicker CX400.1 Bruksanvisning

16 Oktober 2024

Kicker CX660.5 Bruksanvisning

16 Oktober 2024

Kicker IQ1000.1 Bruksanvisning

16 Oktober 2024

Kicker KXA2400.1 Bruksanvisning

16 Oktober 2024

Kicker KXA400.1 Bruksanvisning

16 Oktober 2024

Kicker KXA1200.2 Bruksanvisning

16 Oktober 2024

Kicker IQ500.1 Bruksanvisning

16 Oktober 2024

Kicker KXA1600.1 Bruksanvisning

16 Oktober 2024

Mottaker Manualer

Nyeste Mottaker Manualer

ETON MA 1 Bruksanvisning

19 Mars 2025

KanexPro SP-1X16SL18G Bruksanvisning

14 Mars 2025

Elipson P1 Bruksanvisning

14 Mars 2025

Elipson Stream S300 Xi Bruksanvisning

14 Mars 2025

Elipson WIIM Mini Bruksanvisning

14 Mars 2025

Rexing RoadMate CPStream Bruksanvisning

13 Mars 2025

Marshall Electronics VDA-108-3GS Bruksanvisning

13 Mars 2025

Rega Brio MK7 Bruksanvisning

12 Mars 2025

Aguilar OBP-3 Bruksanvisning

11 Mars 2025

Aguilar AG Preamp Pedal Bruksanvisning

11 Mars 2025