Kramer KT-107-INWL Bruksanvisning

Les nedenfor 📖 manual på norsk for Kramer KT-107-INWL (4 sider) i kategorien Ikke kategorisert. Denne guiden var nyttig for 4 personer og ble vurdert med 4.5 stjerner i gjennomsnitt av 2 brukere

Side 1/4
KT- -INWL 107 Quick Start
P/N:
2 9 0 0 - 3 0 1 1 5 1 QS
Rev:
2
Scan for full manual
KT- -INWL Quick Start Guide 107
This guide helps you install and use your KT-107-INWL for the rst time.
Go to www.kramerav.com/downloads/KT- -INWL107 to download the latest manual and check for updates.
Step 1: Check what’s in the box
4 4x1/2” screws for wood (packed separately)
Outer frame
4 Inner frame M3x8 screws (packed separately
Inner frame
Step 2: Get to know your - -INWL KT 107
The -Wall Kit secures , and Touch Panels safely into a wall (drywall, wood, or KT- -INWL107 In KT-107 -107RB KT -107SKT
concrete).
Step 3: Prepare the surface for installation
For drywall and wooden surfaces:
1. Place the cut-out template (included, use
for drywall and wood installations) over the
surface exactly where you want to install
KT- -INWL107 .
2. Mark the edge inside
(W, H: 19.5cm x 15cm) of the template and
cut an opening in the surface according to
the given dimensions.
Kramer is not responsible for any
damage caused to the surface.
For concrete or block wall surfaces:
Use the Kramer -wall box KT-107-INWB in
(purchased separately) for concrete
installations.
1. Make sure that the prepared opening in
the concrete ts the dimensions of the in-
wall junction box.
2. Insert the into the opening. KT- -INWB107
Make sure to place the ush KT-107-INWB
with the plaster surface.
Step 4: Mount the - -INWL enclosure KT 107
For each surface type you need to use dierent screws to mount the enclosure. KT-107-INWL
For drywall surfaces:
1. Insert the enclosure into the KT- -INWL107
opening.
2. Slightly release the 4 drywall screws until you
notice (via the openings next to the drywall
screws) that the drywall anchor turns
outwards.
3. Tighten the screws to x the enclosure in
place.
Rear view of drywall screw anchor in the vertical position and tightened,
in the horizontal position:
For wooden surfaces:
Insert the 4 wood screws 4x1/2
(supplied) through the wood screw-
openings and tighten to the wooden
surface.
For concrete surfaces:
1. Place the enclosure inside the KT- -INWL107
junction box opening.
2. Insert the 4 concrete screws (supplied with
KT KT- -INWB107 ) through the - -INWL107
enclosure concrete screw-openings and the
screw openings of the junction box, and
tighten.
Step 5: Prepare the Touch Panel for installation
Before attaching the touch panel to the enclosure, you need to attach the panel-mount plate to the rear side of KT- -INWL107
the Touch Panel and then to the on-wall mount.
The -mount plate and the on-wall mount are supplied with the Touch Panel. panel
To prepare the touch panel for installation:
1. Insert the cables through the openings of the
Touch-Panel on-wall mount (for example, a
USB cable to connect to an external device).
2. On the rear side of the Touch Panel, unscrew
the cover and set the cover and screw aside.
3. Attach the panel mount plate onto the rear
side of the Touch Panel using the 4 M2x4
screws (supplied with the Touch Panel) and
tighten.
4. Connect the at cable
between the on-wall mount
and the Touch Panel.

Produkspesifikasjoner

Merke: Kramer
Kategori: Ikke kategorisert
Modell: KT-107-INWL

Trenger du hjelp?

Hvis du trenger hjelp med Kramer KT-107-INWL still et spørsmål nedenfor, og andre brukere vil svare deg




Ikke kategorisert Kramer Manualer

Ikke kategorisert Manualer

Nyeste Ikke kategorisert Manualer