Lectrosonics DNT16i Bruksanvisning
Lectrosonics
Prosessor
DNT16i
Les nedenfor 📖 manual på norsk for Lectrosonics DNT16i (20 sider) i kategorien Prosessor. Denne guiden var nyttig for 5 personer og ble vurdert med 4.5 stjerner i gjennomsnitt av 2 brukere
Side 1/20
DNT Series
DNT16i/DNT0212 Network Processors
INSTALLATION AND STARTUP GUIDE
Rio Rancho, NM, USA
www.lectrosonics.com
Fill in for your records:
Serial Number:
Purchase Date:
A trademark of Audinate Pty Ltd.
DNT Digital Processor
LECTROSONICS, INC.
2
Installation and Quick Start Guide
Rio Rancho, NM 3
Table of Contents
FCC Part 15 Compliance 3 .......................................................
Important
Safety Instructions 4 .........................................................
Overview 5 .................................................................................
What is Dante? 5 ....................................................................
About the DNT Processors 5 ..................................................
Switched and Redundant Modes 5 .........................................
DNT16i Front Panel 6 ................................................................
DNT16i Rear Panel 6 .................................................................
DNT0212 Front Panel 7 .............................................................
DNT0212 Rear Panel 7 ..............................................................
DNT Control Panel Software 8 .................................................
DNT Software Installation 8 .....................................................
About Dante Software 9 ...........................................................
DanteTM Software
Installation 9 ......................................................................
Mandatory Settings 10 .............................................................
Dante Controller Software - Network Settings 10 ...................
DNT Control Panel Software - Signal Flow Configuration 11 ..
DNT Software - USB Connection 11 .......................................
DNT Software - Ethernet Connection 11 ................................
Hardware Connections 12 .......................................................
Installing the chassis into a rack 12 ........................................
Connecting via USB for the First Time 12 ...............................
Setup and Control Port Connections 12 .................................
Programmable Inputs 13 .........................................................
RS-232 Serial Port Wiring 13 ..................................................
Crestron® RS-232 Port Wiring 13 ............................................
Programmable Outputs 13 ......................................................
Network and PC Connections 14 ............................................
Signal Routing 15 .....................................................................
Replacement Parts and Accessories 16 .................................
Service and Repair 17 ..............................................................
Returning Units for Repair 17 .................................................
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. The equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that which the receiver is
connected
• Consult the dealer or an experienced radio/TV technician for help
Changes or modifications to this equipment not expressly approved by Lectrosonics, Inc. could
void the user’s authority to operate it.
Produkspesifikasjoner
| Merke: | Lectrosonics |
| Kategori: | Prosessor |
| Modell: | DNT16i |
Trenger du hjelp?
Hvis du trenger hjelp med Lectrosonics DNT16i still et spørsmål nedenfor, og andre brukere vil svare deg
Prosessor Lectrosonics Manualer
16 Oktober 2024
Prosessor Manualer
- Prosessor Bose
- Prosessor Black And Decker
- Prosessor Radial Engineering
- Prosessor Atlas Sound
- Prosessor Allen & Heath
- Prosessor Ashly
- Prosessor MuxLab
- Prosessor TC Helicon
- Prosessor Bogen
- Prosessor Sonifex
- Prosessor BSS Audio
- Prosessor Drawmer
Nyeste Prosessor Manualer
27 Oktober 2024
27 Oktober 2024
27 Oktober 2024
27 Oktober 2024
22 Oktober 2024
22 Oktober 2024
20 Oktober 2024
20 Oktober 2024
20 Oktober 2024
20 Oktober 2024