LevelOne IFP-0801 Bruksanvisning

LevelOne Bryter IFP-0801

Les nedenfor 📖 manual på norsk for LevelOne IFP-0801 (7 sider) i kategorien Bryter. Denne guiden var nyttig for 3 personer og ble vurdert med 4.5 stjerner i gjennomsnitt av 2 brukere

Side 1/7
1
IFP-0801
8-Port Industrial Fast Ethernet PoE Switch,
4 PoE Outputs, 802.3at PoE+, 6W 12
User Manual
2
FCC MARKING
This Equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference
in which case the user will be required to correct the interference at his own expense.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received; including interference that may
cause undesired operation.
CE MARKING
This equipment complies with the requirements relating to electromagnetic
compatibility, EN 55022 class for ITE, the essential protection requirement of A
Council Directive 2004/108/EC on the approximation of the laws of the Member States
relating to electromagnetic compatibility.
Company has an on-going policy of upgrading its products and it may be possible that
information in this document is not up- -date. Please check with your local to
distributors for the latest information. No part of this document can be copied or
reproduced in any form without written consent from the company.
Trademarks:
All trade names and trademarks are the properties of their respective companies.
Copyright © 2013, All Rights Reserved.
3
Power connection:
This industrial Fast Ethernet 8 port POE switch is equipped with 4 x 10/100M PSE port, each port can deliver
30W POE power. It comes with a 6 pin terminal block. It can be connected with 48-56VDC power source.
Always Make sure to use 56VDC for IEEE802.3at or 30W power connection.
WARNING any exceeded input voltage will not make this unit function and may damage this unit.
To make power connection Follow the printed polarity for V1+, V1-,
V2+, -, and ground. Connect positive wire to V+ , connect negative V2
wire to V-, also connect neutral wire to the ground screw as shown .
Relay You may use 24V@1A relay connection to your external --
device for special purpose. When 2 powers are connected, the relay is
in OPEN mode. When any power source fails, the relay change to
SHORT status.
Power connecting procedure:
STEP 1 Pull out 6 pin terminal block.
STEP 2 Connect wire to V1+, V1-, or V2+, V2-, and Ground the neutral wire to the ground screw.
STEP 3 Plug back 6 pin terminal block to its place.
WARNING
Always ground the power source to maintain a clean power input. Due to too many cheap made power
supplies, it creates too much noise, and it will cause the power input uctuates when connect to this
unit. To avoid this, always ground the power source to gain a clean power input.
Din Rail Bracket x 1
Wall mount bracket x 2
6 pin Terminal Block p3
This unit can be installed by din-rail mounted or wall-mounted. Din-rail brackets and wall-mounted
bracket are included.

Produkspesifikasjoner

Merke: LevelOne
Kategori: Bryter
Modell: IFP-0801

Trenger du hjelp?

Hvis du trenger hjelp med LevelOne IFP-0801 still et spørsmål nedenfor, og andre brukere vil svare deg