Marshall MG15GFX Bruksanvisning

Marshall Mottaker MG15GFX

Les nedenfor 📖 manual på norsk for Marshall MG15GFX (12 sider) i kategorien Mottaker. Denne guiden var nyttig for 20 personer og ble vurdert med 4.5 stjerner i gjennomsnitt av 2 brukere

Last ned PDF

Side 1/12

Warning: Please refer to full

details in separate Important

Safety Instrucons CATS-90009.

Warning: before going any

further, make sure that your amp

is compable with your mains

electricity supply. If you have

any doubt, please seek help from

a qualied technician – your

Marshall dealer can help you

with this.

MAINS INPUT & FUSE

The specic mains input voltage

rang that your amp has been

manufactured for is indicated on

the rear panel of the amp.

Never aempt to bypass the fuse

or t one of the incorrect value

or type.

IMPORTANT SET UP INFORMATION

1. Ensure that the power switch is

set to the o posion.

2. Connect the supplied mains

(power) lead into an electricity

outlet.

3. Ensure that any master volume

and/or output level controls on

the front panel are set to zero.

4. Plug your guitar into the input

jack socket on the front panel.

5. Turn the front panel power

switch on.

6. Turn the volume up to your

preferred level and you’re

ready to play.

TRANSPORTING YOUR EQUIPMENT

Please ensure that your amp is

switched o, unplugged from

the mains electricity supply and

all removable cables have been

disconnected from your equipment

before aempng to move it.

FCC COMPLIANCE STATEMENT

This device complies with part

15 of the FCC Rules. Operaon

is subject to the following two

condions:

1. This device may not cause

harmful interference, and

2. This device must accept any

interference received, including

interference that may cause

undesired operaon.

This equipment has been tested

and found to comply with the

limits for a Class B digital device,

pursuant to part 15 of the FCC

rules. These limits are designed

to provide reasonable protecon

against harmful interference in a

residenal installaon.

This equipment generates, uses

and can radiate radio frequency

energy and, if not installed

and used in accordance with

the instrucons, may cause

harmful interference to radio

communicaons.

However, there is no guarantee

that interference will not occur

in a parcular installaon. If

this equipment does cause

harmful interference to radio or

television recepon, which can

be determined by turning the

equipment o and on, the user is

encouraged to try to correct the

interference by one or more of the

following measures:

• Reorient or relocate the

receiving antenna.

• Increase the separaon

between the equipment and the

receiver.

• Connect the equipment into

an outlet on a circuit dierent

from that to which the receiver

is connected.

• Consult the dealer or an

experienced radio/TV

technician for help.

Cauon: Any changes or

modicaons not expressly

approved by the party

responsible for compliance could

void the users authority to operate

the equipment.

This device complies with CAN

ICES-3(B)/NMB-3(B)

MG15FX &

MG30FX

QUICK START GUIDE

DOWNLOAD THE FULL MANUAL AT

WARNING! SAFETY INSTRUCTIONS

PLEASE READ THIS MANUAL CAREFULLY BEFORE PLUGGING IN.

FOLLOW ALL INSTRUCTIONS AND HEED ALL WARNINGS.

Whilst the informaon contained herein is correct at the me of publicaon, due to its policy of constant improvement and development,

Marshall Amplicaon Plc reserves the right to alter specicaons without prior noce.

Marshall Amplicaon Plc, Denbigh Road, Bletchley, Milton Keynes, MK1 1DQ, England. T: +44 (0) 1908 375411. Registered in England. Registered Number: 805676.

M3311.419

CATS-90025-02

ENGLISH

Product dimensions (height x width x depth):

MG30FX 420mm × 480mm × 225mm Unit weight 10.8kg

MG50FX 505mm × 520mm × 280mm Unit weight 16.6kg

Informazioni disponibili in Lingua italiana. Visita per scaricare il manuale completo in Italiano.marshall.com

LIVE FOR MUSIC

Looking to take the plunge into the music industry?

Marshall Live For Music has lots of advice from industry

specialists and professional musicians to get your

career moving. From geng your rst band together to

securing slots at fesvals around the world, you can nd

everything you need to make your mark in music.

MARSHALL.COM/LIVE-FOR-MUSIC

MARSHALL WORKSHOP

We’ve taken it back to basics and created

the Marshall Workshop videos to help you

nail your sound. From understanding your

equipment to perfecng your playing, the

Marshall Workshop features all the tools you

need to cra that killer sound.

MARSHALL.COM/WORKSHOP

EXPLORE

MARSHALL.COM

ENGLISH

FRONT PANEL FUNCTIONS

1 2 3 4 5 6 7 8 9 10 11 12 13 1514 16 17

CHANNEL SELECTION

The amplier has 4 channels - Clean,

Crunch, OD-1 & OD-2. Pressing

the Clean/Crunch switch (3) selects

between the Clean (Green Light)

and Crunch (Red Light) channels.

Pressing the OD-1/OD-2 switch

(5) selects between the OD-1

(Green Light) and OD-2 (Red Light)

channels.

MODES

The amplier operates in two modes

- Preset and Manual. To change

between these two modes, you must

hold the Tap switch (10) down for at

least two seconds. When in manual

mode the Store switch (12) lights red

and the selected channel light (3 or

5) will start to ash.

The amplier will remember the

last mode it was in aer power o

and revert to it the next me it is

powered on.

Preset

This is the factory default operaon

of the amplier. In Preset mode the

posion of all controls except Master

Volume (13) are stored within each

channel. Each channel should be

considered a preset.

Selecng a channel automacally

recalls the sengs stored within

the channel. To store the updated

sengs, push the Store switch

(12). If you select another channel

without pressing Store (12) then any

altered sengs will be lost as the new

channel and its sengs are recalled.

Manual

In manual mode the amp’s sengs

always match the physical posions

of the controls. Pressing Store (12)

will store the current sengs into

the selected channel. These can then

be recalled when using the unit in

Preset mode.

1. INPUT JACK SOCKET

Input for your guitar. Use a good

quality guitar cable (i.e. one that’s

screened/shielded) to help prevent

noise, interference and unwanted

feedback.

2. GAIN CONTROL

Controls the amount of signal

entering the pre-amp and the

amount of distoron created in the

selected channel.

3. CLEAN/CRUNCH SWITCH

Selects between Clean (green) and

Crunch (red) channels.

4. BASS CONTROL

Turning up the Bass control will add

low-end depth to your sound.

5. OD-1/OD-2 SWITCH

Selects between OD-1 (green) and

OD-2 (red) channels.

6. MIDDLE CONTROL

Adjusng the middle frequencies

will vary the amount of body in your

sound.

7. TREBLE CONTROL

Increasing the Treble will make your

sounds brighter and more cung.

8. REVERB CONTROL

This control lets you add a lush digital

reverb to the selected channel there

are two disnctly dierent sounding

reverb types – Studio or Spring.

9. VOLUME CONTROL

Controls the volume of the selected

channel.

10. TAP (MANUAL) SWITCH

Matches the delay FX me to the me

between two pushes. The LED ashes

at the selected delay me. Holding

down the Tap switch for longer than

2 seconds switches the amp between

manual and preset mode.

11. FX CONTROL

Selects and adjusts one of ve digital

eects - Chorus, Phaser, Flanger,

Delay and Octave.

12. STORE SWITCH

Stores the current amp sengs into

the current channel or to recall with

the oponal footcontroller. When

in manual mode the Store buon

lights red.

13. MASTER CONTROL

Controls the master volume of the

amplier.

14. MP3 LINE IN SOCKET

Jam to your favourite track by

connecng the line out or headphone

output of your player here.

15. FOOTCONTROLLER SOCKET

Socket for the connecon of the

oponal footcontroller (PEDL-90008).

16. HEADPHONE SOCKET

Connecon of headphones will

automacally mute the internal

speaker.

17. POWER SWITCH

The power switch turns your

amplier on and o. A channel switch

will light up when your amplier is

turned on.

Averssement: Veuillez vous

référer à tous les détails dans les

instrucons de sécurité importantes

disnctes CATS-90009.

Mise en garde : Avant de vous

lancer plus avant, assurez-vous que

votre amplicateur est compable

avec votre alimentaon électrique.

Si vous avez le moindre doute,

demandez l’aide d’un technicien

qualié.

ENTRÉE D’ALIMENTATION SECTEUR :

La tension nominale de l’entrée

d’alimentaon pour laquelle

votre amplicateur est conçu est

indiquée sur le panneau arrière.

INFORMATIONS IMPORTANTES

CONCERNANT L’INSTALLATION :

1. Assurez-vous que le

commutateur d’alimentaon

est en posion arrêt.

2. Branchez le cordon

d’alimentaon dans une prise

de courant.

3. Assurez-vous que les commandes

de volume principal et / ou de

niveau de sore du panneau avant

sont réglées à zéro.

4. Branchez votre guitare dans la

prise d’entrée du panneau avant.

5. Acvez l’interrupteur

d’alimentaon du panneau avant.

6. Augmentez le volume au niveau

souhaité et vous êtes prêt à jouer.

TRANSPORTER VOTRE ÉQUIPEMENT :

Veuillez vous assurer que votre

amplicateur est éteint, débranché

de l’alimentaon électrique et que

tous les câbles amovibles ont été

déconnectés de votre équipement

avant d’essayer de le déplacer.

DÉCLARATION DE CONFORMITÉ

Cet appareil est conforme à la

pare 15 des Régulaons FCC.

L’exploitaon est autorisée

aux deux condions suivantes :

1. Cet appareil ne doit pas

produire de brouillage, et

2. L’appareil doit accepter tout

brouillage radioélectrique

subi, même si le brouillage est

suscepble d’en compromere

le fonconnement.

Cet équipement a été testé et

trouvé conforme aux limites

applicables à un appareil

numérique de Classe B, suivant

la Pare 15 des Règles FCC. Ces

limites sont conçues pour apporter

une protecon raisonnable contre

les interférences nuisibles dans un

environnement résidenel.

Cet équipement génère, ulise,

et peut émere de l’énergie de

fréquence radio et, s’il n’est pas

installé et ulisé conformément

aux consignes, risque de causer

des interférences nuisibles aux

communicaons radio.

Il n’existe toutefois aucune garane

que ces interférences n’auront

pas lieu dans une installaon

parculière. Si cet équipement

cause des interférences nuisibles

à la récepon radiophonique

ou télévisée, ce qui peut être

établi en éteignant et rallumant

l’équipement, l’ulisateur est

encouragé à prendre une plusieurs

des mesures suivantes pour

résoudre ces interférences :

• Réorienter ou déplacer

l’antenne de récepon.

• Augmenter la distance entre

l’équipement et le récepteur.

• Brancher l’équipement dans

une sore circuit diérente de

celle dans laquelle le récepteur

est branché.

• Demander l’aide de son

revendeur ou d’un technicien

radio/TV expérimenté.

MISE EN GARDE : Tout

changement ou modicaon

eectué sans avoir été

expressément approuvé par

la pare responsable de sa

conformité risque d’annuler le

droit d’exploitaon de l’équipement

par son ulisateur.

Cet équipement est conforme aux

normes CAN ICES-3(B)/NMB-3(B)

MG15FX &

MG30FX

GUIDE DE DÉMARRAGE

TÉLÉCHARGEZ LE MANUEL COMPLET SUR

MISE EN GARDE ! CONSIGNES DE SÉCURITÉVEUILLEZ LIRE ATTENTIVEMENT CE MANUEL A VANT DE LE BRANCHER. SUIVEZ TOUTES LES INSTRUCTIONS ET PRENEZ EN COMPTE TOUTES LES MISES EN GARDE.

Bien que les informaons contenues dans ce document soient correctes au moment de leur publicaon, en raison de sa polique d’amélioraon et de développement constants, Marshall

Amplicaon Plc se réserve le droit de modier ces spécicaons sans avis préalable.

Marshall Amplicaon Plc, Denbigh Road, Bletchley, Milton Keynes, MK1 1DQ, Angleterre. T : +44 (0) 1908 375411. Enregistré en Angleterre. Enregistré au numéro : 805676.

FRANÇAIS

Dimensions du produit (hauteur x largeur x profondeur):

MG30FX 420mm × 480mm × 225mm Poids 10.8kg

MG50FX 505mm × 520mm × 280mm Poids 16.6kg