Rockustics Coconutz Bruksanvisning

Rockustics Høyttaler Coconutz

Les nedenfor 📖 manual på norsk for Rockustics Coconutz (2 sider) i kategorien Høyttaler. Denne guiden var nyttig for 3 personer og ble vurdert med 4.5 stjerner i gjennomsnitt av 2 brukere

Last ned PDF
Side 1/2
Coconutz™
INSTALL INSTRUCTIONS
© 2021 MSE Audio. Rev. 02.19.2021
Ultra-Fidelity Outdoor Speakers
Contact: MSE Audio, 855.663.5600 / 913.663.5600 / sales@mseaudio.com
Please read the following instructions carefully before installing
your Rockustics® Coconutz™ speaker. If you have any questions
regarding installation that are not answered in the following
directions, please contact your local sound contractor, or the
Rockustics®/MSE Audio® technical support team.
Basic Wiring
( Diagram A) Locate speaker wire on the top of the Coconutz.
If necessary, strip the wire ends and trim the wire to the
appropriate length. Use the supplied silicone wire nut to
connect the positive (red) leads of the speaker and input wires.
Repeat this step with the negative (black) leads.
NOTE: The provided wire nuts are meant for permanent installa-
tion use only. If you are temporarily wiring the speakers, do not
use these wire nuts. In the event you have used the wire nuts,
and need to re-wire your system, do not attempt to unscrew the
nuts. Instead, clip the wires below the nut, and follow the steps
in the section with a new pair of waterproof wire
Basic Wiring
nuts (these are available at most hardware stores).
Mounting Instructions
NOTE: You will need one (1) mounting hook or eyelet rated for
30lbs (not supplied) per pair of Coconutz.
1) The Coconuts speakers are intended to be mounted using
the supplied hanging cable assembly (Diagram B).
2) It will be necessary to install a hook, loop, or eyelet (not
supplied) (Diagram C) that can adequately support the combined
weight of speakers being installed. Be sure to use hardware that
is rated for the combined total load of the speakers (30 lbs) and
ensure it is properly secured to the mounting surface.
3) (Diagram D) Clip one each of the cable ends to each of the
eyebolts in the Coconutz speaker.
5) Wire the speaker as described in the Basic Wiring section,
ensuring the weight of the speaker is supported by the hanging
cables, as opposed to the speaker wires.
Diagram A
Diagram B Diagram C
Diagram D Diagram E
Coconutz™
INSTALL INSTRUCTIONS
© 2021 MSE Audio. Rev. 02.19.2021
Ultra-Fidelity Outdoor Speakers
Contact: MSE Audio, 855.663.5600 / 913.663.5600 / sales@mseaudio.com
Optimizing Speaker Placement for Best Sound
and Aesthetics
Rockustics recommends hanging your Coconutz in bunches of
2 or 4 units. To ensure your lovely bunch of Coconutz sounds
as good as it looks, hang them between 8’ and 12’ above
ground level.
Be sure to account for the wires which will run from the speaker
to your stereo or audio source. Camouage wires by running
them behind dense tree leaves or wrapping them in colored tape.
Cautions and Maintenance
All Rockustics speakers are sealed and fully weatherproof.
However, DO NOT place speakers where the grille will be in the
path of a sprinkler system. Sprinklers typically have a high water
pressure level that can damage speaker cones if hit directly.
In the rare event the speaker grille holes accumulate build up
of debris (such as soil, dust or sand), the speaker may become
damaged. If build up does occur, simply rinse the grille holes
with a garden hose set to a low pressure level. Accumulated
debris may also promote undesired insect trafc into the
speaker. Insects may eat through the speaker cone.
Chemical sprays may also cause damage to the rubber of the
speaker cone. This includes bug spray, deck sealant, some
fertilizers and oil based products. Speakers MUST be covered
when applying these treatments or chemicals in your yard.
For environments that get snow and ice during the winter months,
be sure to check that the openings and woofer cone are clear
and there is no hard-packed snow or ice built up in these areas
before playing. If there is ice or snow present on the cone, use a
hair dryer set on a low setting to melt it away. If the speakers are
not going to be used during winter months, it is recommended
that they either be disconnected and brought indoors, or cov-
ered with a plastic bag to help protect the speaker components.
Wiring Coconutz in Series
If installing 2 units of the Coconutz, follow the wiring instructions
in Diagram F for 2 speaker connection. Wire one of each
speaker to the left and right channels of the amplier, respectively.
If installing 4 units of the Coconutz, then each pair must be
wired together in a series connection to each channel of the
amplier. Follow the wiring instructions in Diagram G for 4
speaker connection.
2 Speaker Wiring Diagram
PUSH PUSH
Channel 1 Channel 2
Channel 1 Channel 2 =(-) Negative
=(+) Positive
4 Speaker Series Wiring Diagram
PUSH PUSH
Channel 1 Channel 2
Channel 1 Channel 2 =(-) Negative
=(+) Positive
=Series Connection
Diagram G
Diagram F

Produkspesifikasjoner

Merke: Rockustics
Kategori: Høyttaler
Modell: Coconutz

Trenger du hjelp?

Hvis du trenger hjelp med Rockustics Coconutz still et spørsmål nedenfor, og andre brukere vil svare deg


Høyttaler Rockustics Manualer

Rockustics

Rockustics BlockRock Bruksanvisning

15 Mars 2025
Rockustics

Rockustics Coconutz Bruksanvisning

15 Mars 2025
Rockustics

Rockustics StoneHenge II-G Bruksanvisning

10 Mars 2025
Rockustics

Rockustics StoneHenge II-S Bruksanvisning

10 Mars 2025

Høyttaler Manualer

Nyeste Høyttaler Manualer

Elipson

Elipson IC6 Bruksanvisning

16 Mars 2025
Monster

Monster MT-401 Bruksanvisning

14 Mars 2025
Monster

Monster MT-F5 Bruksanvisning

14 Mars 2025
Monster

Monster MT-607 Bruksanvisning

14 Mars 2025
Elipson

Elipson Horus 10C Bruksanvisning

14 Mars 2025
Elipson

Elipson INF IW8 Bruksanvisning

14 Mars 2025
Elipson

Elipson INF IW6 Bruksanvisning

14 Mars 2025
Elipson

Elipson BS50 Tribute Bruksanvisning

14 Mars 2025
Elipson

Elipson Heritage XLS7 Bruksanvisning

14 Mars 2025
Elipson

Elipson Horus 8S Bruksanvisning

14 Mars 2025