Schwaiger ZHD01 Bruksanvisning

Schwaiger Termostat ZHD01

Les nedenfor 📖 manual på norsk for Schwaiger ZHD01 (2 sider) i kategorien Termostat. Denne guiden var nyttig for 4 personer og ble vurdert med 4.5 stjerner i gjennomsnitt av 2 brukere

Last ned PDF

Side 1/2

USER MANUAL ZHD01

TEMPERATURE SENSOR

ZHD01

MANUFACTURER INFORMATION

Dear Customer,

should you require technical advice and your

retailer could not help please contact our

technical support.

Schwaiger GmbH

Würzburger Straße 17 90579 Langenzenn

Hotline: +49 (0) 9101 702-199

www.schwaiger.de info@schwaiger.de

BDA_ZHD01

Business hours:

Monday to Thursday: 08:00 - 17:00

Friday: 08:00 - 14:30

HOME AUTOMATION

Congratulations and thank you for purchasing the Schwaiger ZHD01

product. Below you will find useful operating guidelines.

Display information

Display LED Explanation

Room temperature displayed

Rapid green flashing

Red flashing

Flashes

Runs insertions or deletions

Red flashing every

150 seconds

Red flashing every

30 seconds

Insertions or deletions failed

Z-Wave information

General device class Multi-level sensor

Specific device class Routing multilevel sensor

Device type Routing slave

SDK 4.55

NWI Yes

Explorer frames Yes

Manufacturer ID 0x0002

Product type ID 0x0003

Product ID 0x8010

Introduction

Schwaiger ZHD01 is a battery-operated temperature sensor. If it is integrated into the wireless

Z-Wave network, the control buttons can be used to control the heating system.

Disposal information

This device contains no batteries. It is an electrical device. It can be disposed of free of charge at

specified disposal sites.

EC Declaration of Conformity

„Hereby Schwaiger GmbH declares that the ZHD01 product is in compliance with the essential requi-

rements and other relevant provisions of Directive 1999/5/EC. “ The Declaration of Conformity can be

found at the following address: http://www.schwaiger.de/downloads

Installation

LED button

INCREASE temperature

Display

(with backlight)

LOWER temperature

1. Remove the back panel by

sliding it downwards.

3. Fasten the back panel to the wall.

2. Replace the batteries.

4. Gently push the Z-Wave RS on the back panel.

Z-Wave command classes

Command Class Version Description

BASIC V1 • Basic SET: Not supported

• Basic GET: Multi-level sensor get

• Basic REPORT: Multi-level sensor report

(1 °C accuracy)

MANUFACTURER_

SPECIFIC

V2 ID from Danfoss and Z-Wave RS

VERSION V2 Version of command classes, of the Z-Wave Library

and of Z-Wave RS

BATTERY V1 Battery status

MULTI_CMD V1 Conserve battery power by transmitting multiple com-

mands in a single package

WAKE_UP V2 Switch-on intervals of 5 min to 24 h (default: 60

minutes)

PROTECTION V2 0 = No protection

2 = User interface locked

CONFIGURATION V2 Specific Z-Wave RS configuration

SENSOR_MULTILEVEL V6 Specifies the value from the room temperature sensor

again

CENTRAL_SCENE V1 By pressing the LED button the transmission of

CENTRAL_SCENE_ NOTIFICATION is triggered.

THERMOSTAT_

SETPOINT

V3 When selecting a temperature setpoint on the display

controller, the setpoint is reported.

SCHEDULE V1 When selecting a temperature and a number of hours

on the display controller reported the program change

values.

INDICATOR V1 Control of the LED display.

Paste in Z-Wave

• Make sure that Z-Wave RS is in the factory defaults setting.

• Activate „Inclusion/Paste“ on the Z-Wave controller.

• Press the LED button on Z-Wave RS.

• Check the process status on the controller and Z-Wave RS.

Technical specifications

Battery Alkali 2 x AA, 1.5 V

Battery life

Up to 4-5 years

Backlight

Green LED

Ambient temperature

0˚ to +40 ˚C

Battery monitoring The sensor has a built-in monitoring circuit

which detects a low or critical battery level.

Transmission frequency 868.42 MHz

Transmission range in normal buildings

Up to 30 m

Transmission power Max. 1 mW

IP degree of protection 21

Dimensions 81 mm x 66 mm x 21 mm

Configuration Command ClassFunctions

No. Configuration

parameter

Standard

setting

Area Coding

1 Temperature Report

threshold

0,5 °C 0.1 to 10 °C 2 bytes

1 = 0.1 °C

100 = 10.0 °C

2 Set-point display

resolution

0,5 °C From 0.1 to 10 ° C in

steps of 0.1 ° C

2 bytes

1 = 0.1 °C

100 = 10.0 °C

3 Min. set-point and

override limit

12 °C Min. 0 ° C to max.

setpoint/output

2 bytes

0 = 0 °C

40 = 40 °C

4 Max set-point and

override limit

28 °C Min. setpoint/output

to max. 40 °C

6 Setpoint control

function

Activated Deactivated/activated 1 byte

0 = deactivated

1 = activated

7 Temporarily override

scheduler

Activated Deactivated/activated

8 Setpoint in

Thermostat_

Setpoint_Reports

Heating Heating #1,

cooling #1,

auto changeover

1 byte

1 = heating #1

2 = cooling #1

10 = auto

changeover

9 LED on time 100 ms 100 to 500 ms in

steps of 100 ms

1 byte

1 = 100 ms

5 = 500 ms

5 LED Flash period 1 s 0 to 65,535 seconds 2 bytes

10 Number of LED

flashes (duration)

5 0 to 255 x flashes 1 byte

11 LED Color Green Green, red 1 byte

0x01 = green

0x02 = red

1. Raumtemperatursensor

Command Class SENSOR_

MULTILEVEL

The room temperature is shown on the

display as the icon indicates. If inserted

in the Z-Wave network the temperature

is reported to the controller when the

device is switched on as well as during

changes in temperature, in which the

configured limit is exceeded.

Display accuracy 0,1 °C

Sensor read Every 5 minutes

Report send When switching on

If you exceed the

reporting threshold

CONFIGURATION

COMMAND CLASS

Default setting Area

Report threshold 0,5 °C 0,1 to 10 °C

2. Rocker switch

Command Class CENTRAL_SCENE When clicking the LED button a

CENTRAL_SCENE_NOTIFICATION is

sent to the controller.

Supported key

attributes

0x00/0x01/0x02

3. LED control

Command Class INDICATOR The controller can trigger and stop a

flashing session on the LED button using

the set display command. The frequency,

flashing frequency and colour of the

session are controlled by 4 configuration

parameters.

Indicator Set 0xFF = start

LED flashing session

0x00 = stop

current session

CONFIGURATION

COMMAND CLASS

Default setting Area

LED on time 100 ms 100 to 500 ms in steps of 100 ms

LED Flash period 1 s 0 to 65535 seconds

Number of LED flashes

(duration)

5 0 to 255 x flashing

LED colour Green Green, red

4. Change setpoint

Command Class THERMOSTAT_

SETPOINT

The up and down arrow keys are used

to select a new setpoint temperature.

After selection of a setpoint this flashes

for 5 seconds. Thereafter, the measured

temperature is displayed again and the

Z-Wave RS sends the selected tempera-

ture as THERMOSTAT_SETPOINT_

REPORT to the Z-Wave controller.

Indicator Set 0xFF = LED-

flashing session starts

0x00 = stop

current session

CONFIGURATION

COMMAND CLASS

Default setting Area

Setpoint control

function

Activated Deactivated/activated

Set-point display

resolution

0,5 °C From 0.1 to 10 °C in steps of 0.1 °C

Max set-point and

override limit

28 °C From min. setpoint/clip to max. 40 °C

Min. set-point and

override limit

12 °C From min. 0 °C to max. setpoint/clip

Setpoint in

Thermostat_

Setpoint_Reports

Heating #1 Heating #1,

cooling #1,

auto changeover

5. Scheduler override thermostat

Command Class SCHEDULE

The up and down arrow keys are used to

select the temporary override temperature.

The selected value flashes on the display for

5 seconds. Press the LED button before the

5 seconds are over to select the number of

hours for the override. The selected number

of hours flashes for 5 seconds. Thereafter,

the measured temperature is displayed again

and the Z-Wave RS sends the selected tem-

perature and the number of hours as SCHE-

DULE_REPORT to the Z-Wave controller.

CONFIGURATION

COMMAND CLASS

Default setting Area

Temporarily override

scheduler

Activated Deactivated/activated

Set-point display

resolution

0,5 °C From 0.1 to 10 °C in steps of 0.1 °C

Max set-point and

override limit

28 °C From min. setpoint/clip to max. 40 °C

Min. set-point and

override limit

12 °C From min. 0 °C to max. setpoint/clip

Z-Wave networks

Z-Wave RS can be installed and operated in any Z-Wave network with other Z-Wave certified devices

from other manufacturers. Independently from respective manufacturers all permanently powered

Z-Wave nodes function as Repeaters within a network

Z-Wave best practice

• After the successful „paste“ the controller must send a WAKE_UP_INTERVAL_SET command to

Z-Wave RS to specify where and when Z-Wave RS should communicate wirelessly.

• After issuing the command WAKE_UP_INTERVAL_SET, the controller must assign return routes, so

that Z-Wave RS can reach its goal, i.e. the node ID given by the command WAKE_UP_INTERVAL_SET

• The node ID given by the command WAKE_UP_INTERVAL_SET applies to a permanently switched-on

device that responds to commands sent from Z-Wave RS. If the controller is turned off for long

periods, the batteries of the Z-Wave RS are used up too quickly.

• Although Z-Wave RS responds to individual commands, multiple commands must always be used to

ensure the two year battery life.

Delete from Z-Wave

• Press „Exclusion/Remove“ on the Z-Wave controller.

• Keep the three buttons on the Z-Wave RS pressed for 5 seconds (up, down and LED buttons).

• Check the process status on the controller and Z-Wave RS.

Z-Wave wake up

A controller can only communicate with Z-Wave RS when the device is switched on. The intervals in

which Z-Wave RS is turned on can be adjusted by means of the command class „switch on.“ The

default setting for switching on is 60 minutes. Z-Wave RS can be turned on manually by pressing one

of three buttons and then stays on for 10 seconds.

Resetting to factory default settings

1. Remove one of the batteries. 2. Hold the LED button for about five seconds when

reinserting the battery until the LED flashes red.

The Z-Wave RS is now reset to the factory default settings.

Produkspesifikasjoner

Merke:	Schwaiger
Kategori:	Termostat
Modell:	ZHD01

Trenger du hjelp?

Hvis du trenger hjelp med Schwaiger ZHD01 still et spørsmål nedenfor, og andre brukere vil svare deg

Ditt navn*

Din e-post*

Skriv spørsmålet ditt her

Termostat Schwaiger Manualer

Schwaiger ZHD01 Bruksanvisning

27 Oktober 2024

Termostat Manualer

Nyeste Termostat Manualer

Vemer Keo-B Bruksanvisning

27 Oktober 2024

King K101 Bruksanvisning

27 Oktober 2024

Vemer Thalos Key Bruksanvisning

27 Oktober 2024

Fantini Cosmi 1598089 Bruksanvisning

27 Oktober 2024

Honeywell CT87K1004/U1 Bruksanvisning

27 Oktober 2024

Danfoss RET1000 MS Bruksanvisning

27 Oktober 2024

Honeywell TH4110B1009/U Bruksanvisning

27 Oktober 2024

Niko 88001 Bruksanvisning

27 Oktober 2024

Niko 88000 Bruksanvisning

27 Oktober 2024

Honeywell Round Clock Deluxe T8725M Bruksanvisning

27 Oktober 2024