SoundTube CM500i Bruksanvisning

Les nedenfor 📖 manual på norsk for SoundTube CM500i (4 sider) i kategorien Høyttaler. Denne guiden var nyttig for 2 personer og ble vurdert med 4.5 stjerner i gjennomsnitt av 2 brukere

Side 1/4
Ceiling tile
Grille and bezel
Grille and bezel
seismic restraint
Seismic restraint anchor tab
Euroblock connector
Cover plate
Strain relief (not included) may
be used with cover plate.
Tile bridge
Euroblock jack
Baffle
Styrofoam installation aid/paint mask
Speed Wingmounting arms
Cover plate clamping screw
Signal wire
Box contents
1 Speaker
1 Euroblock connector
1 Grille and bezel
1 Styrofoam installation aid/paint mask
1 Cover plate
1 Tile bridge
Install Instructions For:
CM400i, CM500i, CM590i, CM600i, CM690i, CM800i & CM890i speakers
Min
6.4 mm (0.25 in)
Max
42.9 mm (1.69 in)
Ceiling thickness tolerances
Do not spec or install speaker near support beam, ventilation duct or
other structure that may interfere with speaker function or dispersion.
Warning Warning
SoundTube speakers must be installed by a professional audio installer/contractor. For safety and for
optimum audio performance, installer must follow all directions issued by SoundTube Entertainment.
© 2009 SoundTube Entertainment, Inc. All rights reserved. PN INS-CMI Rev05.26.09
1.435.647.9555
| | 800.647.TUBE
www.soundtube.com
CM400i, CM500i, CM600i, CM690i, CM800i, CM890i UL listed 1480 & 2043
1. Unpack speaker & set
aside grille assembly.
3. Use included tile bridge
to mark cutout in tile.
4. Use Rotozip or other tool
to cut hole.
11. Select the tap position
by adjusting rotary switch
to desired high impedance
value or voice coil bypass
mode. Switch is preset to
maximum tap setting in
70.7 V mode (33 W or 66 W).
13. Attach grille position the
grille over the baffle and allow
magnets to attract grille into
place. Be sure grille is properly
centered over baffle.
12. Attach grille & bezel
seismic restraint to baffle
with provided screw.
5. Insert speaker into
mounting hole on ground
with installation aid in
place. Screw down both
bolts on the baffle face to
actuate the mounting wings.
Firmly secure both bolts
do not over-tighten. Put
assembly into tile grid.
. If required, attach the
seismic restraint system to
the sheet-metal tab on the
rear panel of the speaker
(safety cable not included).
6. Thread signal wire through
cover plate. Connect signal
wire to 4-pin Euroblock plug.
Tighten unused terminal
screws. Use inside positive
and negative inputs for either
voice coil or distributed
systems. For daisy chaining,
use outside positive and
negative terminals.
7. Insert the Euroblock plug
into the Euroblock jack on
rear panel of speaker and
replace cover plate.
For UL-compliant installations
strain relief (not supplied) may
be inserted into hole in cover
plate.
1.435.647.9555
| | 800.647.TUBE
www.soundtube.com
SoundTube also provides optional Pre Construction Brackets & Architectural Grilles for the CMi product line.
Installation instructions for these accessories are included with specific accessory packaging.
Droptile Ceiling Install Instructions For:
CM400i, CM500i, CM590i, CM600i, CM690i, CM800i &CM890i speakers
Hole Diameters
CM500i & CM590i
228.6 mm (9.00 in)
CM600i, CM800i & CM801i
325.1 mm (12.80 in)
9. If you are not painting the
ceiling, remove & discard the
paint mask.
10. If you are painting the
ceiling after the speaker is
installed, leave the paint mask
in place until paint is dry.
2. Keep Styrofoam
installation aid/paint
mask attached to
speaker until speaker
installation is complete.
12. Attach grille & bezel
seismic restraint to baffle
with provided screw.
1.435.647.9555
| | 800.647.TUBE
www.soundtube.com
Hole Diameters
CM500i &
228.6 mm (9.00 in)
CM600i, CM800i & CM801i
325.1 mm (12.80 in)
1. Unpack speaker & set
aside grille assembly.
2. Keep Styrofoam
installation aid/paint mask
attached to speaker until
speaker installation is
complete.
3. Use included tile bridge
to mark cutout in sheetrock.
4. Use Rotozip or other tool
to cut hole.
11. Select the tap position
by adjusting rotary switch
to desired high impedance
value or voice coil bypass
mode. Switch is preset to
maximum tap setting in
70.7 V mode (33 W or 66 W).
13. Attach grille position the
grille over the baffle and allow
magnets to attract grille into
place. Be sure grille is properly
centered over baffle.
7. If required, attach the
seismic restraint system to
the sheet-metal tab on the
rear panel of the speaker
(safety cable not included).
5. Thread signal wire through
cover plate. Connect signal
wire to 4-pin Euroblock plug.
Tighten unused terminal
screws. Use inside positive
and negative inputs for either
voice coil or distributed
systems. For daisy chaining,
use outside positive and
negative terminals.
9. If you are not painting the
ceiling, remove & discard the
paint mask.
10. If you are painting the
ceiling after the speaker is
installed, leave the paint mask
in place until paint is dry.
6. Insert the Euroblock plug
into the Euroblock jack on
rear panel of speaker and
replace cover plate.
For UL-compliant installations
strain relief (not supplied) may
be inserted into hole in cover
plate.
SoundTube also provides optional Pre Construction Brackets & Architectural Grilles for the CMi product line.
Installation instructions for these accessories are included with specific accessory packaging.
Sheetrock Ceiling Install Instructions For:
CM400i, CM500i, CM590i, CM600i, CM690i, CM800i &CM890i speakers
8. Insert speaker into
mounting hole with
installation aid in place.
Screw down both bolts on
the baffle face to actuate
the mounting wings. Firmly
secure both bolts – do not
over-tighten.

Produkspesifikasjoner

Merke: SoundTube
Kategori: Høyttaler
Modell: CM500i

Trenger du hjelp?

Hvis du trenger hjelp med SoundTube CM500i still et spørsmål nedenfor, og andre brukere vil svare deg




Høyttaler SoundTube Manualer

Høyttaler Manualer

Nyeste Høyttaler Manualer