StarTech.com PLATEIDE2CF Bruksanvisning

StarTech.com Ikke kategorisert PLATEIDE2CF

Les nedenfor 📖 manual på norsk for StarTech.com PLATEIDE2CF (2 sider) i kategorien Ikke kategorisert. Denne guiden var nyttig for 4 personer og ble vurdert med 4.5 stjerner i gjennomsnitt av 2 brukere

Last ned PDF

Side 1/2

Instruction Manual

DE: Bedienungsanleitung - de.startech.com

FR: Guide de l'utilisateur - fr.startech.com

ES: Guía del usuario - es.startech.com

IT: Guida per l'uso - it.startech.com

NL: Gebruiksaanwijzing - nl.startech.com

PT: Guia do usuário - pt.startech.com

Manual Revision: 06/29/2011

For the most up-to-date information, please visit: www.startech.com

Packaging Contents

• 1 x IDE to CF Adapter with Full Prole Bracket

• 1 x SP4 Floppy to LP4 Molex Adapter Cable

• 1 x Instruction Manual

System Requirements

• Available Full Prole expansion card slot in computer case

• IDE enabled motherboard with available 40 or 44-pin IDE

connector

• Operating system independent

PLATEIDE2CF

IDE to CF Adapter Card with a PCI Bracket

Installation

WARNING! This card, like all computer equipment, can be

severely damaged by static electricity. Be sure that you are

properly grounded before opening your computer case or

touching the card. StarTech.com recommends that you wear an

anti-static strap when installing any computer component. If an

anti-static strap is unavailable, discharge yourself of any static

electricity build-up by touching a large grounded metal surface

(such as the computer case) for several seconds. Also be careful

to handle the card by its edges or the installation bracket.

1. Turn your computer o and any peripherals connected to

the computer (i.e. Printers, external hard drives, etc.). Unplug

the power cable from the rear of the power supply on the

back of the computer and disconnect all peripheral devices.

2. Remove the cover from the computer case. See

documentation for your computer system for details.

3. Locate an open expansion card slot on the computer

case and remove the metal cover plate on the rear of the

computer case (Refer to documentation for your computer

system for details.).

4. Set the Master/Slave mode jumper on the CF adapter. See

“IDE Mode Jumper” section for further details

5. Fasten the bracket of the CF adapter to the rear of the case.

*actual product may vary from photos

6. Connect a 40 or 44-pin IDE cable from the motherboard to

the CF adapter.

7. Connect an SP4 oppy power cable from the computer

power supply to the CF adapter. If the computer does not

have an available SP4 power connector, an LP4 Molex to SP4

power cable adapter is included.

8. Place the cover back onto the computer case.

9. Insert the power cable into the socket on the power supply

and reconnect all other connectors removed in Step 1.

10. Insert a CF card into the card slot on the adapter.

**IDE standard does NOT support hot swapping. Do not

insert or remove the CF card, while the system is running.

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols

This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to

StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s)

to which this manual applies by the third-party company in question. Regardless of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby acknowledges that all

trademarks, registered trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the property of their respective holders.

Technical Support

StarTech.com’s lifetime technical support is an integral part of our commitment to provide industry-leading solutions. If you ever need help with your product, visit www.startech.com/support and access

our comprehensive selection of online tools, documentation, and downloads.

For the latest drivers/software, please visit www.startech.com/downloads

Warranty Information

This product is backed by a lifetime warranty.

In addition, StarTech.com warrants its products against defects in materials and workmanship for the periods noted, following the initial date of purchase. During this period, the products may be returned

for repair, or replacement with equivalent products at our discretion. The warranty covers parts and labor costs only. StarTech.com does not warrant its products from defects or damages arising from

misuse, abuse, alteration, or normal wear and tear.

Limitation of Liability

In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their ocers, directors, employees or agents) for any damages (whether direct or indirect, special, punitive, incidental,

consequential, or otherwise), loss of prots, loss of business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product. Some states do not allow

the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations or exclusions contained in this statement may not apply to you.

Specications

Host Interface IDE (ATA-133)

Form Factor Full Prole

Connectors 1 x 40-pin IDE male

1 x 44-pin IDE male

1 x SP4 Floppy power

1 x 50-pin CF card slot

LEDs N/A

Compatible Cards CompactFlash™ type I/II,

Hitachi® Microdrive®

Dimensions (LxWxH) 218.0mm x 45.0mm x 158.0mm

Weight 60g