VARI-LITE VL800 Propar Bruksanvisning

VARI-LITE Ikke kategorisert VL800 Propar

Les nedenfor 📖 manual på norsk for VARI-LITE VL800 Propar (14 sider) i kategorien Ikke kategorisert. Denne guiden var nyttig for 3 personer og ble vurdert med 4.5 stjerner i gjennomsnitt av 2 brukere

Last ned PDF
Side 1/14
VL800 PROPAR
USER MANUAL
2
USER MANUAL
912400575012UM W W W.VA R I - L I T E . C O M
PREFACE
1. ABOUT THIS MAN UAL
The document provides installation and operation instructions for the following products:
• VL800 PROPAR
Read all instructions before installing or using this product. Retain this manual for future reference.
Additional product information and descriptions may be found on the product specifi cation sheet.
2. INCLUDED ITEMS
Each VL800 PROPAR luminaire includes the following items:
• VL800 PROPAR
• Quick Start Guide
3. SAFETY NOTICES
• Unpack and check carefully for damage from shipping before using the unit.
• Do install and operate by operator.
• Use safety tether when mounting.
• Install only in locations with adequate ventilation of at least 50cm clearance from adjacent surfaces.
• Ensure sure that ventilation slots are not blocked to prevent overheating.
• Before operating, ensure that the voltage and frequency of power supply match the power requirements
of the unit.
• It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.
• Maximum ambient temperature TA : 40°C minimum ambient temperature TA : 0°. Don’t operate it where
the temperature is higher than this.
• Do not connect the device to any dimmer pack.
• First run, there will be smoke or smells, and all disappearing a few minutes later.
• Make sure there are no fl ammable materials close to the unit while operating, as it is fi re hazard.
• Look over power wires carefully, replace immediately if there is any damage.
• When in use, fi xture surface temperature may reach up to 65°C. DO NOT touch the housing.
• Never run on for a long time lest shortening lifespan.
• Do not operate in dirty and dusty environment, also cleaning fi xtures regularly.
• Do not allow children to operate the fi xture.
• Do not touch any wire during operation as there might be a hazard of electric shock.
• Avoid power wires together around other cables.
• In the event of serious operating problem, stop using the unit immediately.
• Never turn on and o the unit time after time.
• The housing, the lenses, or the ultraviolet fi lter must be replaced if they are visibly damaged.
• Do not open the unit as there are no user serviceable parts inside. Never try to repair the unit by yourself.
Repairs carried out by unskilled people can lead to damage or malfunction. Please contact the nearest
Authorized Service Center.
• Disconnect the mains power if the fi xture is not used for a long time.
• Do use original packing materials once transport it again.
• To prevent or reduce the risk of electrical shock or fi re, do not expose the unit to rain or moisture.
• Do not look directly at the LED light beam while the fi xture is on.
• To protect the machine, power o 10s rear can electrify.
3
USER MA NUAL
912400575012UM W W W.VA R I - L I T E . C O M
INSTALLATI ON AND SETUP
1. MOUNTING
The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is fi rmly fi xed to
avoid vibration and slipping while operating. Always ensure that the structure to which you are attaching the
unit is secure and is able to support a weight of 10 times of the unit’s weight. Also always use a safety cable that
can hold 12 times of the weight of the unit when installing the fi xture.
The equipment must be fi xed by professionals. And it must be fi xed at a place where is out of the touch of peo-
ple and has no one pass by or under it.
2. SET UP
CONTROL PANEL
MAIN FUNCTIONS
To select any functions, press the MENU button until the required one is shown on the display. Select the func-
tion by the ENTER button and the display will blink. Use the DOWN and UP button to change the mode. Once
the required mode has been selected, press the ENTER button to setup or it will automatically return to the
main functions without any change after idling one minute. Back to the functions without any change press the
MENU button. The main functions are shown in TABLE 1.
1 LCD display - shows the menu and selected functions
2 Buttons:
MENU - To select the programming functions
DOWN - To go backward in the selected functions
UP - To go forward in the selected functions
ENTER - To confirm the selected functions
5
6
7
12
3
4
3 DMX IN - 5-pin XLR cable to link DMX console
4 DMX OUT - 5-pin XLR cable to link to the next unit
5 Fuse T5A - protects the unit from damage due to over current
6 Power In - connacts to power supply
7 Power Out - connects to next fixture

Produkspesifikasjoner

Merke: VARI-LITE
Kategori: Ikke kategorisert
Modell: VL800 Propar

Trenger du hjelp?

Hvis du trenger hjelp med VARI-LITE VL800 Propar still et spørsmål nedenfor, og andre brukere vil svare deg


Ikke kategorisert VARI-LITE Manualer

VARI-LITE

VARI-LITE VL800 Propar Bruksanvisning

27 Mars 2025

Ikke kategorisert Manualer

Nyeste Ikke kategorisert Manualer

AEG

AEG AirFry A9OOAFWM Bruksanvisning

1 April 2025
Atlona

Atlona AT-HDR-EX-70C-TX Bruksanvisning

1 April 2025
Parallels

Parallels Plesk Panel 11.5 Bruksanvisning

1 April 2025
Sunny

Sunny Fresh Art Easel Bruksanvisning

1 April 2025
Crestron

Crestron CAEN-1X1 Bruksanvisning

1 April 2025
Crestron

Crestron CAEN-4X2 Bruksanvisning

1 April 2025
Hamlet

Hamlet HXD25TCU31 Bruksanvisning

1 April 2025
Crestron

Crestron CAEN-7X1 Bruksanvisning

1 April 2025
Crestron

Crestron CAEN-7X2 Bruksanvisning

1 April 2025
Crestron

Crestron CAEN-2X1 Bruksanvisning

1 April 2025