Victrola VPT-800 Bruksanvisning
Victrola
Platespiller
VPT-800
Les nedenfor 📖 manual på norsk for Victrola VPT-800 (10 sider) i kategorien Platespiller. Denne guiden var nyttig for 3 personer og ble vurdert med 4.5 stjerner i gjennomsnitt av 2 brukere
Side 1/10
INSTRUCTION MAN UAL
VPT-80 0
A U T O M AT I C
Turntable
Dust cover
Platter with belt
Slipmat
45 RPM adapter
Power adapter / RCA cable
U N PAC K
Plug in power adapter.
Place 45 RPM adapter in corner compartment.
Remove foam support from back of tonearm.
Remove tonearm twist tie.
Remove tape and clear stylus cover.
Note: Gently pull stylus cover forward to remove.
P R E PA R E T U R N TA B L E
LOCATE TH E FOL LOWING ITEMS
Lower the platter on to the turntable.
Rotate the platter until the hole with the white ribbon is directly over the gold motor.
Pull both ends of the ribbon outward until the belt is extended past the motor.
Slowly release the belt until it is secured around the motor, then remove the ribbon.
Note: Ensure the belt is flat against the motor and not twisted.
Place the slipmat on the platter.
I N S TA L L P L AT T E R
PL ACE T URNTABLE ON A FLAT AND LE V EL SUR FACE
COMPLETE ALL STEPS BEFORE USE
C O N N E C T TO S P E A K E R S
Press and hold to power ON / OFF.
Single press to switch output modes:
RCA OUTPUT - LED: Flashes white, then solid white.
VINYLSTREAM™ (BLUETOOTH OUTPUT ) - LED: Flashes blue.
Note: When powering back ON, the turntable will return to the
last used output mode.
MULTI-FUNCTION BUTTON
Enter VINYLSTREAM (Bluetooth output) mode and turntable will
automatically enter pairing mode. LED: Flashes blue.
Make sure your Bluetooth device is in pairing mode.
Turntable will automatically pair to your Bluetooth device.
Once paired, LED will turn solid blue for one second, then turn solid white.
Note: Volume is controlled by Bluetooth device.
PAIR BLUETOOTH SPEAKER OR HEADPHONES
CONNECT RCA OUTPUT
Connect the turntable to external speakers or receiver using the included RCA cable.
RED PLUG - RED (RIGHT) JACK Insert into the
WHITE PLUG - WHITE (LEFT) JACK Insert into the
Set pre-amplier switch to the correct output:
LINE - If connecting to a line-level input.
PHONO - If connecting to an phono-level input.
For PHONO output, it is recommended to use a grounding wire (not included)
to connect the ground pin between the turntable and the external component.
Enter wired (RCA) output mode. LED: Flashes white, the solid white.
Produkspesifikasjoner
| Merke: | Victrola |
| Kategori: | Platespiller |
| Modell: | VPT-800 |
Trenger du hjelp?
Hvis du trenger hjelp med Victrola VPT-800 still et spørsmål nedenfor, og andre brukere vil svare deg
Platespiller Victrola Manualer
31 Desember 2025
31 Desember 2025
31 Desember 2025
12 Desember 2024
22 Oktober 2024
Platespiller Manualer
- Platespiller Aiwa
- Platespiller Denver
- Platespiller Pro-Ject
- Platespiller Audio-Technica
- Platespiller Pyle
- Platespiller Sencor
- Platespiller Auna
- Platespiller Fenton
- Platespiller Audizio
- Platespiller Muse
- Platespiller MoFi
- Platespiller Reloop
- Platespiller Music Hall
- Platespiller Crosley
- Platespiller Thorens
- Platespiller Rekkord
- Platespiller Sumiko
- Platespiller House Of Marley
- Platespiller Classic Phono
- Platespiller Akai
- Platespiller Lenoxx
Nyeste Platespiller Manualer
7 Januar 2025
7 Januar 2025
6 Januar 2025
6 Januar 2025
4 Januar 2025
30 Desember 2025
7 Desember 2024
7 Desember 2024
7 Desember 2024
7 Desember 2024