XO UIM1585NOPA Bruksanvisning
XO
Isbitmaskin
UIM1585NOPA
Les nedenfor 📖 manual på norsk for XO UIM1585NOPA (32 sider) i kategorien Isbitmaskin. Denne guiden var nyttig for 5 personer og ble vurdert med 4.5 stjerner i gjennomsnitt av 2 brukere
Side 1/32

I worked really hard
on this manual -
so please read it...
UNDERCOUNTER NUGGET ICE MAKERS
MODELS:
XOUIMN1585NO, XOUIMN1585NOP
XOUIMN1585NOA, XOUIMN1585NOPA

2
REGISTRATION HELPS YOU BY -

3
where things are
please read and follow
all safety instructions
It’s for your
own good...
Honest.

4
heres’s ten steps for a quick & easy install
RISK OF CHILD ENTRAPMENT!
An empty refrigerator is a very dangerous attraction to children.
Remove door gaskets, latches, lids, lock and/or doors from unused or discarded appliances,
or take other actions to guarantee them harmless.
Always dispose of old appliances in accordance with local laws and regulations.
1
2
3
4
5
6
7
8
9
10
Inspect cabinet opening for water, drain and electrical connections.
The 1/4” O.D. water supply line must include isolation valve and should include an inline water
filter (consult manual). Do NOT use a self-piecing valve for the supply connection. Water
supply must have a minimum pressure of 20 psi and a maximum of 80 psi. Cold water
should be betw
o
een 50 F and 90 F - N
o OTE: warmer water will slow ice production.
is strongly recommended.
Drain tubing will be 5/8” ID gravity fed or 3/8” ID for a pump model. All horizontal drain
runs must drop 1/4” per foot. The drain should include an air gap device to prevent
siphoning and a sanitary trap. A restricted or inadequ te drain can result in poor icea
production and possible flooding.
Electrical requirement is 15a dedicated, grounded circuit.
Route water supply tubing to the water inlet located at the rear of the unit.
Connect the drain tubing to either the pump discharge or the barbed gravity fed elbow.
Be sure nothing is kinked, and excess slack is removed.
Be sure the electrical connection is secure into the wall outlet.
Slide the machine into location or cavity being careful not to allow for any kinks to occur
in the water inlet and drain tubing.
Adjust the Ice Maker to level using the leg levelers.
Add approximately 2-3 quarts of water to the bin and make certain it is draining properly
and check for leaks. If water does not drain, stop and verify tubing is not restricted.
Wash down the interior of the machine with a mild detergent solution (consult manual)
Turn the machine on and allow it to make ice for approximately 30-35 minutes to verify
ice is being produced and water is draining freely. Be sure to check the cube size, shape
and clarity. Discard the first batch of ice.
Adjust if needed.
Always do one last check to be sure all water and drain connections are leak free.

5
STANDARD HEIGHT
XOUIM 15 5 & XOUIM 15 5 PN 8 NO N 8 NO
ADA HEIGHT
XOUIMN1585NOA & XOUIMN1585NOPA
2
these are the models
covered in this
book
take a minute to circle your model above
and record your serial number
here in case you need it later
INDOOR NUGGET
GOURMET ICE MAKER

7
Serious injury, fire or death...
Okay -

8
When installing, remember you need
to leave ready access to both the power
Cut access to an adjoining cabinet to
locate outlet and water there.
a perfect fit
install under counter
ALL XO UNDERCOUNTER
UNITS A E E-WIREDRRIV PR
WITH LOW P E PLUGSROFIL
FOR EASY INSTALLATION
4"
(100mm)
7"
(178mm)
15”
WH E N IN S TAL L ING W ITH
TH E H INGE SIDE NEXT TO A WA LL -
LEAV DE ATE SPACE FOR E A QU
YOUR DOOR HANDLE
DOOR HAS THE ABILITY TO OPEN TO 115
(381mm)
MINIMUM
Standard Height Units
33-3/4” MINIMUM
(853mm)
ADA Height Units
31-7/8” MINIMUM
(808mm)
Clearance
Gap
90°
Door Swing
WALL

9
a perfect fit
your xo is this big ( )or small, as the case would be
XOUIMN1585__ & XOUIMN1585__A ICE MAKER
33-
STANDARD HEIGHT
(853mm)
31-13/16”
STANDARD HEIGHT
(808mm)
9/16”
W
H
height & width
depth
22-25/32”
(579mm)
D
THE OVERALL DEPTH SHOWN (22-25/32”) INCLUDES THE DOOR WITH 3/4” PANEL.
THE DEPTH OF THE ICE MAKER CABINET ONLY IS 20-13/32”
14-15/16” WIDE
(379mm)
TOP VIEW
115
90

10
before you install
check a few things
e
Is the installation location COOL, DRY, LEVEL and away from direct sun.
The water supply valve must provide positive shut off capability and be readily accessible.
Does the unit have a dedicated 115V three prong, properly grounded outlet?
The Cold Water supply is 1/4” O.D. tube, it should be 50 to 90 F and be between 20 and 80 psi.
(NOTE: as the inlet water temperature increases - production efficiency goes down.)
YOU WILL NEED -
A few simple hand tools:
Pump pliers, adjustable wrench, #2 Phillips head screwdriver, level, razor knife
AND a few hardware items:
Teflon tape or Pipe dope
5/8” I.D. drain hose and hose clamps (if installing a gravity drain model)
1/4” O.D. water supply hose
Air Gap Device and/or Sanitary Trap (depending on your installation).
Water filter with isolation valve
Depending on your installation you will probably require additional site specific plumbing fittings
Water source tub
Drain hose
o o
120 leV Out t

12
Plan the arrangement of the water supply pipes. You will need both a water supply line and
a drain (see section on installing a gravity drain unit or pump drain unit)
If the tap water has a high level of minerals, an inline filter will be required.
Attach the water supply line to the rear of the unit
with flexible tube to the fitting indicated here.
The tubing must be long enough to permit the
unit to be pulled out for service.
Water supply should be between 20psi and 80psi.
Attach the drain to the connection indicated here
If you are installing an XOUIMN1585NO unit with a
gravity drain, the line must be pitched down
1/4” per ft to ensure correct drainage.
If the drain is positioned at a higher elevation than
the connection on the rear of the unit, a pump
will be required. Use model XOUIMN1586NOP.
This unit comes with a pre-installed drain pump
capable on discharging to a drain up to 8’ above
the unit.
IMPORTANT: The keep drains as short and straight
as possible for optimal performance.
The electric power, water supply pipeline and drain pipeline must be in compliance with all
provisions under the local laws and building regulations.
IMPORTANT: The product is designed for use in a fixed condition but it may be required to
pull the product out for service. Therefore, do not install any material at the front, upper or
lower end of the product which may be an obstacle when pulling the product out.
Once the unit is in place, use the leveling legs to ensure the unit is level.
Each side should have at least 1/16" of space for projection of the screw head near the bottom.
the plumbing
1/4” O.D.
DRAIN
WATER
SUPPLY

13
INSTALLING THE XOUIMN1585 without a drain pump.
Position the ice maker in front of the opening. Level the unit using the leveling legs.
Wash and flush the water supply tube and connect the unit to the cold water isolation valve.
Prepare the drain. The drain must be pitched downward at a drop of 1/4” per foot to drain properly.
Horizontal runs of 5’ or more must be anchored to a wall for support to prevent sagging.
A sanitary trap and air gap must be installed in the line prior to entering the home’s drain system.
The trap prevents sewer gas from flowing back to the ice maker.
The air gap device prevents siphoning drain water back into the ice maker.
Cut the 5/8” ID drain hose (not supplied) to the required length. Immerse the hose in warm water to make
installation easie
hose to the drain using hose clamps.
r, then using a threaded hose barb connection sealed with teflon tape, connect the drain
Turn the water supply on and check to ensure there are no leaks.
If there are no leaks, plug the unit into the electrical outlet.
Press the switch to the “ICE” position. The compressor will run approximately 3 - 5 minutes.
Slide the unit back into it’s final position and recheck to ensure it is level.
REMEMBER to adhere to all local building codes and regulations
with gravity drain
DRAIN VENT
THE DRAIN POINT
MUST BE LOWER
THAN THE DRAIN
OUTLET OF THE
ICE MAKER
AI
DEVICE
R GAP
SANITARY TRAP
If you purchase a gravity drain unit
and find you need one with a pump
the XOUIMN1585 can easily be
retrofitted with one in the field.
Simply order a XOUIMPUMP from
www.xoappliance.com

14
INSTALLING THE XOUIM1565SP with DRAIN PUMP.
Position the ice maker in front of the opening.
Level the unit using the leveling legs.
Wash and flush the water supply tube and connect the unit to the cold water isolation valve.
Cut the 3/8” diameter drain hose to the required length. Immerse the hose in warm water to make
installation easie
(9’ of 3/8” ID drain hose is included with pump models)
r, then connect the drain hose to the drain using hose clamps.
IMPORTANT: Check local codes to determine if an air gap is required between the drain and the pump.
Turn the water supply on and check to ensure there are no leaks.
If there are no leaks, plug the unit into the electrical outlet.
Fill the ice container with clean tap water approximately 3/4 full. The drain pump should turn on and pump
the water out. Check again for leakage.
Press the switch to the “ICE” position. The compressor will run approximately 3 - 5 minutes.
Fill the ice container to 3/4 full once more. Block the drain tube while the pump is running.
The pump should continue to run.
Slide the unit back into it’s final position and re-check to ensure it is level.
REMEMBER to adhere to all local building codes and regulations
with drain pump
DRAIN VENT
THE DRAIN POINT
MAY BE HIGHER
THAN THE DRAIN
OUTLET OF THE
ICE MAKER
SANITARY TRAP
AIR GAP DEVICE
Produkspesifikasjoner
Merke: | XO |
Kategori: | Isbitmaskin |
Modell: | UIM1585NOPA |
Trenger du hjelp?
Hvis du trenger hjelp med XO UIM1585NOPA still et spørsmål nedenfor, og andre brukere vil svare deg
Isbitmaskin XO Manualer

16 Oktober 2024

16 Oktober 2024

16 Oktober 2024

16 Oktober 2024

16 Oktober 2024

16 Oktober 2024

16 Oktober 2024

16 Oktober 2024

16 Oktober 2024
Isbitmaskin Manualer
- Isbitmaskin NewAir
- Isbitmaskin Domo
- Isbitmaskin Cecotec
- Isbitmaskin Summit
- Isbitmaskin Hendi
- Isbitmaskin GE
- Isbitmaskin Costway
- Isbitmaskin Thermostar
- Isbitmaskin Igloo
- Isbitmaskin True
- Isbitmaskin Atosa
- Isbitmaskin Girmi
- Isbitmaskin H.Koenig
- Isbitmaskin Manitowoc
- Isbitmaskin U-Line
- Isbitmaskin Hoshizaki
- Isbitmaskin Metos
- Isbitmaskin Baccarat
- Isbitmaskin Sheffield
Nyeste Isbitmaskin Manualer

5 April 2025

5 April 2025

4 Mars 2025

4 Mars 2025

21 Februar 2025

18 Februar 2025

17 Februar 2025

11 Februar 2025

7 Januar 2025

7 Januar 2025