AMX NMX-ENC-N1134A Bruksanvisning

AMX Ikke kategorisert NMX-ENC-N1134A

Les nedenfor 📖 manual på norsk for AMX NMX-ENC-N1134A (2 sider) i kategorien Ikke kategorisert. Denne guiden var nyttig for 3 personer og ble vurdert med 4.5 stjerner i gjennomsnitt av 2 brukere

Last ned PDF
Side 1/2
QUICK START GUIDE
N-Series N1134A MPC Encoder
Overview
The N-Series N1134A MPC (Minimum Proprietary Compression) Encoder features input
and output scaling, serial, balanced audio, HD-SDI video connection, and Power-over-
Ethernet (PoE). This unit also offers 1G SFP support for uncompressed networked AV
video and USB control inputs for KVM keyboard and mouse over IP.
The P1 port on the rear of the unit is an SFP network connection. FIG. 1 shows the front
and rear views of the unit.
Basic Installation Guidelines
Establishing Connection
N1134A devices are shipped with as their default IP mode. The IP address is DHCP
assigned automatically based on the network DHCP server. If no DHCP server is found,
the unit will use mode instead (with a default IP address of 169.254.xxx.xxx).Auto IP
Before using your N1134A unit, it must be configured using the free N-Able device
management software. However, you will not be able to configure units until they are in
the same subnet as the host computer.
The sample steps below show how the required changes (to the host computer's IP
settings) are made in a Windows environment.
Steps for IP address configuration:
1. From the Control Panel > Network and Internet dialog box, select Network and
Sharing Center.
2. Select .Change adapter settings
3. Select the wired interface connected to your AV network.
4. Click the button.Properties
5. Scroll down in the list to the Internet Protocol Version 4 (TCP/IPv4) option.
Highlight it and click the button.Properties
6. Enable the option, and enter the static IP address Use the following IP address
provided to you by your network administrator.
NOTE: If the computer does not need Internet access, you can simply enter a unique
169.254.xxx.xxx IP address with a 255.255.0.0 Subnet mask. Please contact your
network administrator if you are unsure of how to configure the existing interface. If the
computer has a statically-assigned IP address, click on the Advanced button. Then click
Add to enter a unique 169.254.xxx.xxx address with a subnet of 255.255.0.0.
Logging in Using N-Able Software
Once the host IP address is configured properly, you can view all discovered units using
the N-Able software. Access the N1000 MPC units from the following tabs:
• tab - is listed in the Unit Management N1000 Encoder/Decoder Type field.
• tab - N1000 MPC units are found on the sub-tab of this Video Matrix N1000
screen.
Double-click the unit’s name (in one of the lists mentioned above) to view its Settings
page. If prompted, enter admin and password for the default username and password.
Once logged in, you can change the username and password (using the options on the
unit’s page). From this page, you can access any of the main pages of the Settings
unit’s GUI.
NOTE: If you would like for N-Able to support auto-login to your units, make sure N-Able’s
Device Auto-login settings match the unit’s username and password (by selecting N-Able
> Settings from the N-Able tool bar).
NOTE: N1000 MPC units force HTTPS connections, so your web browser may give you a
security warning. N-Able on Windows will ask you to download OpenSSL for Windows to
connect HTTPS.
FIG. 1 N1134A USB AND SFP PORTS
Connections Options
Power: PoE: Connect the unit’s P0 port to an active, PoE-enabled network
switch
External power supply: If not using PoE for power, connect a 12V
regulated power supply (part number N9312) to the unit’s two-pin
terminal block plug connector labeled .+12V 2A
Network: If using PoE to power the unit, you should already have a PoE:
network connection.
External power: P0 If not using PoE, connect the port to the
network using an Ethernet cable, or connect the port to the P1
network with the appropriate cable (fiber transceiver or direct-
attach cable is required for SFP connections).
Daisy-chain configuration: Once network connection is
established to one unit, you can daisy-chain additional units by
connecting Ethernet cables between devices using their P0 and/or
P1 ports. Keep in mind that the number of units supported in this
configuration is limited by bandwidth (total aggregate streams
must be less than 1 Gb/s).
NOTE: PoE power is only supplied to the unit connected directly to
the network. All other units in the daisy-chain must have an
external power supply.
Video: • For video encoding of a digital source, connect the source to the
Encoder’s port using a video cable with a BNC HD-SDI IN
connector (or adapter).
Audio: • For audio encoding, connect a line level analog audio source to
the input terminal block plug connector, or Audio
• Use the embedded audio from the video source.
One USB Mini-B Port
Two USB Standard-A Ports
Supported by N1233 Decoders
N1134A Front View
1G SFP ports accepts compatible
fiber transceivers or direct attach
cables (fiber or copper cabling)
N1134A Rear View
(inactive for N1134A Encoder)
Product Specifications
Power
Requirements:
PoE: Can be powered via a PoE switch or other equipment with a PoE
source. Conforms to IEEE 802.3af Class 3 (802.3at Type 1).
External power supply: 2.0 Amp @ 12 Volts DC; 100-240 Volts AC power
supply; Part number N9312 (sold separately).
Dimensions
(HWD):
1.05” x 7.888” x 5.5” (2.67cm x 20.04cm x 14cm)
Weight: 1.55 lbs (0.7kg)
Certifications: FCC, CE, and NTRL
Environmental: Temperature: 32° to 104°F (0° to 40°C)
Humidity: 10% to 90% RH (non-condensing)
Mounting
Options:
Stand alone, surface mount, wall mount, or rack mount.*
*Mounting wings (part number N9101) required for surface and wall mounting. Rack
shelf (part number N9102) or card cage (part number N9206) required for rack
mounting. Shelf accommodates two side-by-side N-Series Encoders and Decoders.
Card cage accommodates up to six N-Series Encoder and Decoder cards (mix and
match any series).
NOTE: The SFP port supports 1000BASE-X or 1000BASE-T connections only.
© 2017 Harman. All rights reserved. Modero, AMX, AV FOR AN IT WORLD, HARMAN, and their respective logos are registered trademarks of
HARMAN. Oracle, Java and any other company or brand name referenced may be trademarks/registered trademarks of their respective companies.
AMX does not assume responsibility for errors or omissions. AMX also reserves the right to alter specifications without prior notice at any time.
The AMX Warranty and Return Policy and related documents can be viewed/downloaded at www.amx.com.
3000 RESEARCH DRIVE, RICHARDSON, TX 75082 AMX.com | 800.222.0193 | 469.624.8000 | +1.469.624.7400 | fax 469.624.7153
AMX (UK) LTD, AMX by HARMAN - Unit C, Auster Road, Clifton Moor, York, YO30 4GD United Kingdom • +44 1904-343-100 • www.amx.com/eu/
5089915-00 REV: B
Last Revised: 8/2017
Basic KVM Setup
The N1134A Encoder is KVM-capable. By default, USB connections are enabled and
configured to follow video switching. Follow these steps for basic KVM setup. To learn
about some of the more advanced KVM capabilities, see the section Advanced KVM
Setup (with added security features).
1. On the N1134A Encoder, connect the USB Mini-B port to the computer to be
controlled.
2. Connect the computer’s video output to the Encoder’s port. HD-SDI IN
3. On the N1233 Decoder, connect the to the display. HDMI OUT
4. Connect a USB keyboard and mouse to the Decoder’s USB Standard-A ports (they
can be plugged into either port).
NOTE: For wireless devices, simply plug the wireless signal receivers into these
ports. For keyboard and mouse combos (with a single connection) use the
keyboard port.
5. Using N-Able, click the Unit Management tab.
6. Click the button to discover your new devices (if you have not Auto Discover
already done so).
7. Once discovery is complete (and you see the new units listed in N-Able), click the
Video Matrix tab.
8. On the matrix, click the common cell for the desired Encoder/Decoder streaming
combination. See the screen shot below for an example.
9. Click the button to make the change to your matrix. The radio button turns Take
green to indicate the connection was successful.
Video/USB Switching Options
USB Follows Video: By default, units can be switched using N-Able without modifying
the configuration. When you switch video streams (using the matrix as shown above)
the USB functionality will follow the video.
Independent USB Switching: USB Matrix Use N-Able’s tab to switch USB control
(without affecting video).
Independent Video Switching: To switch video streams affecting USB control, without
first select from N-Able’s main menu. When the N-Able > Settings N-Able Settings
dialog box is displayed, disable the USB follows Video switching for KVM units. Now you
can use the to switch video streams only.Video Matrix
Advanced KVM Functionality: To have the ability to use KVM hotkeys for switching, KVM
Advanced Settings must be enabled on the individual unit (select KVM from the top of
the unit’s web interface). The next section discusses these settings in more detail.
Advanced KVM Setup (with added security features)
You can configure devices for more advanced KVM operation on the Encoder and
Decoder pages. To access these pages, double-click the unit’s name in the matrix KVM
and click at the top of the page (see below).KVM Settings
FIG. 3 SELECTING THE KVM PAGE
NOTE: Many of these options are easier to manage in N-Able’s KVM Wizard (especially in
large configurations). Select Tools > KVM Wizard from the N-Able main menu to access
the wizard.
The following table describes some of the more advanced functionality. It is important
to note that many of these options only appear on the page when is enabled KVM USB
as well as .KVM Advanced Settings
Warning! You must assign KVM passwords to your Encoders and Decoders (as well as
change the default login password from admin/password) in order for your system to
be secure.
Troubleshooting Guidelines
Please contact technical support at svsisupport@harman.com or 256.461.7143
(x9900) for assistance with any installation issues.
FIG. 2 CREATING STREAMING COMBINATIONS
Enabling this cell causes
Conference Room Decoder to listen
to . Conference Room Encoder
Click to apply changes. Take
Options Descriptions
Permission Levels This feature determines which Decoders can communicate
with which Encoders. A Decoder must have a permission
level that is equal to or greater than the Encoder in order for
communication to be successful.
KVM Encoders table Use the table (on the Decoder’s page) KVM Encoders KVM
to:
• Let the Decoder know the Encoder passwords it needs to
establish communication.
• Assign Encoder hotkeys.
• Add/remove Encoders from the Decoder’s list.
Passwords By default, KVM streams are encrypted with a common
password. You can change the password on the Settings
page of the Encoder. If you change Encoder passwords, you
will need to supply the new information to the Decoders to
allow communication to continue.
A Decoder only receives password information for the
Encoders on the network that have been associated with
that Decoder as mentioned previously.
Hotkeys To use hotkeys for easy switching, enable KVM Directory
Screen Enable on the Decoder’s KVM page. You can now
access the KVM Directory Screen at any time by pressing the
<Scr Lk> button twice on the keyboard connected to the
Decoder. This screen displays all Encoders associated with
that Decoder (and their corresponding hotkey).
Import and export KVM CSV
files.
Multiple Encoders and Decoders can be configured from a
single CSV file (which is generated using the KVM Wizard in
N-Able). Once all changes are made, upload the file to each
unit using its page.Click the button, KVM Choose File
browse to the CSV file you exported from the wizard, and
click the button. Upload
Problem Possible Solution
Video is not
transmitting.
• Verify that the Encoder setting is turned on. TX Enable
(Encoders ship from the factory with their video output turned
off by default.)
Local Play graphic is
displayed.
• Verify Decoder is assigned to view a valid stream in the N-Able
matrix.
• Verify Decoder is currently in live play mode (black text on matrix
view).
• Verify network is properly configured and set up. If needed,
connect Encoder directly to Decoder to verify network issues.
Host Play graphic is
displayed.
• Verify Encoder is in live play mode (black text in matrix).
• Verify source is attached and is outputting a valid signal (SDI
LED on Encoder is on).
Unsupported
Resolution graphic is
displayed.
• Change source resolution to a valid resolution (try 720p60).
• Verify cabling is correct.
Copy Protected Content
screen is displayed.
• Contact technical support.
Black screen/no
graphic is displayed.
• Set Decoder to local play. If the local play graphic does not
appear, check the display input settings and cabling.
• If local play appears, set Decoder to live play and verify network
is configured properly.
No audio is detected. • If there is no audio on all Decoders, verify audio settings are
correct on Encoder.
• If there is no audio on a single Decoder, verify audio settings are
correct on Decoder.

Produkspesifikasjoner

Merke: AMX
Kategori: Ikke kategorisert
Modell: NMX-ENC-N1134A

Trenger du hjelp?

Hvis du trenger hjelp med AMX NMX-ENC-N1134A still et spørsmål nedenfor, og andre brukere vil svare deg


Ikke kategorisert AMX Manualer

AMX

AMX NMX-ENC-N2315-WP Bruksanvisning

19 Oktober 2024
AMX

AMX NMX-ENC-N1133 Bruksanvisning

19 Oktober 2024
AMX

AMX NMX-ENC-N1134A Bruksanvisning

19 Oktober 2024
AMX

AMX NMX-DEC-N2211 Bruksanvisning

19 Oktober 2024
AMX

AMX NMX-DEC-N1233 Bruksanvisning

19 Oktober 2024
AMX

AMX NMX-DEC-N2222A Bruksanvisning

19 Oktober 2024
AMX

AMX NMX-DEC-N1222A Bruksanvisning

19 Oktober 2024
AMX

AMX TPC-WIN8-TAB Bruksanvisning

16 Oktober 2024

Ikke kategorisert Manualer

Nyeste Ikke kategorisert Manualer

Daewoo

Daewoo Cyclone Essential FLR00038 Bruksanvisning

28 Oktober 2024
IFM

IFM SU6631 Bruksanvisning

28 Oktober 2024
IFM

IFM SU7031 Bruksanvisning

28 Oktober 2024
IFM

IFM SV8051 Bruksanvisning

28 Oktober 2024
Daewoo

Daewoo AVS1464 Bruksanvisning

28 Oktober 2024
IFM

IFM PT5300 Bruksanvisning

28 Oktober 2024
IFM

IFM KTE301 Bruksanvisning

28 Oktober 2024
IFM

IFM OVP810 Bruksanvisning

28 Oktober 2024
IFM

IFM SF0516 Bruksanvisning

28 Oktober 2024
IFM

IFM TSM701 Bruksanvisning

28 Oktober 2024