Apc SYNX-980214 Bruksanvisning

Apc Ikke kategorisert SYNX-980214

Les nedenfor 📖 manual på norsk for Apc SYNX-980214 (1 sider) i kategorien Ikke kategorisert. Denne guiden var nyttig for 3 personer og ble vurdert med 4.5 stjerner i gjennomsnitt av 2 brukere

Last ned PDF

Side 1/1

Modular Data Line

Installation Manual

Surge Protection System

Thank you for purchasing APC’s Modular Data Line Surge Protection System. Please fill out the supplied

Warranty Registration Card or an on-line Product Warranty Registration form at www.apc.com.

If the device arrived damaged, notify the carrier.

If the device requires service, do not return it to the dealer. The following steps should

be taken:

1. Go to http://www.apc.com/support/.

2. Have the model number, serial number and date of purchase available. Be

prepared to troubleshoot the problem with an APC Technical Support

representative. If this is not successful, APC will issue a Return Merchandise

Authorization (RMA) number and a shipping address.

APC warrants its products to be free from defects in materials and workmanship under

normal use and service for the lifetime of the original purchaser. Its obligation under

this warranty is limited to repairing or replacing, at its sole option, any such defective

products. To obtain service under warranty you must obtain a Returned Material

Authorization (RMA) number from APC or an APC Service Center. Product must be

returned to APC or an APC Service Center with transportation charges prepaid and

must be accompanied by a brief description of the problem and proof of date and place

of purchase.

This warranty applies only to the original purchaser.

For information please call APC Customer Service Center at:

American Power Conversion 1-401-789-5735 or 1-800-800-4APC (4272)

132 Fairgrounds Road http://www.apc.com/support or

West Kingston, RI 01892 USA esupport@apcc.com

Service

Limited Lifetime Warranty

Customer Service / Technical Support

Model: PNETR5

Item Specification

Lines Protected Pins 1-8 on RJ-45 connector

Mode of Protection Between send/receive pairs and

any signal line to ground.

Peak Voltage ± 2,000 Volts, 1.2/ 50 µs test

waveform

Peak Current 150 Amps, 8/ 20 µs test

waveform

Breakover (turn on)

Voltage

60 V peak nominal between send/

receive pairs

Isolation Compliant with the applicable

safety isolation requirements of

standards IEEE 802.3 or IEEE

802.5

Response Time <1ns

Agency Approvals UL 497B recognized

Model: PTEL2R

Item Specification

Lines Protected Pins 3&4 and 5&6 on RJ-45

connector; accepts RJ-45 &

RJ-11 plugs

Mode of Protection Metallic (Tip - Ring) and

longitudinal (Tip + Ring -

Ground)

Peak Voltage ± 2,000 Volts, 1.2/50 µs test

waveform

Peak Current 150 Amps, 8/ 20 µs test

waveform

Breakover (turn on)

Voltage

270 V peak nominal between

tip and ring

Overload Protection Solid-state self-resetting fuse

Response Time <1 ns

Agency Approvals UL 497A recognized

Model: P232R

Note: The PRM24 Chassis is listed to UL 60950 and VDE

approved.

Item Specification

Lines Protected Pins 1-8 on RJ-45 connector

Mode of Protection Between send/receive pairs

and any signal line to ground

Peak Voltage ± 2,000 Volts, 1.2/50 µs test

waveform

Peak Current 150 Amps, 8/ 20 µs test

waveform

Breakover (turn on)

Voltage

19 V nominal between send/

receive pairs

Response Time <1 ns

Module Information

Federal Communications Commission (FCC) Notice

This equipment contains an FCC compliant RJ-45 modular jack. It is designed to be connected to the telephone

network or premises wiring using compatible modular plugs and cabling which comply with the requirements

of FCC Part 68 rules. The Ringer Equivalence Number (REN) is used to determine the number of devices

which may be connected to the telephone line. An excessive REN may cause the equipment to not ring in

response to an incoming call. In most areas, the sum of RENs of all equipment on a line should not exceed five

(5).

In the unlikely event that this equipment causes harm to the telephone network, the telephone company can

temporarily disconnect your service. The telephone company will try to warn you in advance of any such

disconnection, but if advance notice isn’t practical, it may disconnect the service first and notify you as soon as

possible afterwards. In the event such a disconnection is deemed necessary, you will be advised of your right to

file a complaint with the FCC.

From time to time, the telephone company may make changes in its facilities, equipment, or operations which

could affect the operation of connected equipment. If this occurs, the telephone company is required to provide

you with advance notice so you can make the modifications necessary to maintain uninterrupted service. This

product is not serviceable by the user.

To Equipment

to be Protected

From

Signal

Source

Figure 1. Typical Installation

.apc.com

Model: PDIGTR

Item Specification

Lines Protected Pins 1-8 on RJ-45 connector

Mode of Protection Between send/receive pairs and

any signal line to ground

Peak Voltage ± 2,000 Volts, 1.2/50 µs test

waveform

Peak Current 100A (max with 10X 1000 µs

waveform

Operating Current 150 mA Maximum

Breakover (turn on)

Voltage

Metallic (line-to-line): 60VDC

Nominal

Response Time <1 ns

Regulatory Approval /

Classification

UL 497A recognized, FCC

APC’s Modular Data Line Surge Protection System consists of the PRM24 Chassis, mounting hardware, ground wire, and

associated data line modules (PNETR5 for Network Protection, PTEL2R for Analog Telephone Protection, P232R for RS232

Protection,and PDIGTR for Digital Telephone Protection). The chassis was designed for use in any EIA-standard 19-inch (48.2

cm) wide equipment rack or enclosure.

This manual provides basic information necessary to install the chassis and associated modules in a rack or enclosure.

Procedures provided in this document are not intended to supercede local standards or codes. Reference the

Telecommunications Industries Association and Electronic Industries Alliance publication “Commercial Building,

Telecommunications Cabling Standard, General Requirements” (document number TIA/EIA-568-B.1-2001) to ensure proper

installation of system wiring.

Model PNETR5 (Network Protection)

The PNETR5 module will protect the port of a Network Interface Card, hub or other local area network

(LAN) equipment from damage caused by lightning-generated electrical transients. This module provides

surge protection for 10Base-T, 100Base-T4, 100Base-TX, 100VG or Token Ring Type 3 UTP port (RJ-45),

and VOIP applications. PNETR5 complies with applicable ISO/IEC Standard 8802-3 (IEEE 802.3) or 8802-

5 (IEEE 802.5) requirements.

In applications where the network data transmission rate is high, insertion loss introduced by in-line devices

becomes a significant consideration where cable lengths are particularly long. At the 100 Mbp/s data

transmission rate, there is a small insertion loss introduced by the PNETR5. Use Table 1 to approximate the

insertion loss based on cable length effectively introduced by the PNETR5 by installed cable Category level

or type. The ISO/IEC 8802-3 standard specifies a maximum UTP cable length of 100 meters per segment at

10/100 Mbp/s. For Thinnet, the maximum cable length is 185 meters (607 feet).

Table 1

EIA/TIA 568

Category or Cable

Type

Frequency

(MHz)

Attenuation

(db/100m)

Equivalent Cable

Length (m)

3 10 9.8 1.0 (3.3 ft)

16 13.1 1.10 (3.5 ft)

4 10 7.2 1.4 (4.5 ft)

16 8.9 1.6 (5.2 ft)

5 10 6.6 1.5 (4.9 ft)

16 8.2 1.7 (5.6 ft)

5 100 22 12.5 (41 ft)

Model PTEL2R (Analog Telephone Protection)

The PTEL2R module protects analog telephones, ADSL, ISDN2, voice mail and

automated answering systems, fax machines and modems from damage caused by

lightning-generated electrical transients. Each PTEL2R protects up to 2 lines.

Warning: Disconnect module wires before removing any module. Do not put fingers

or any object inside the chassis.

Model P232R (RS232 Protection)

The P232R module is for use with RS232 communication equipment (RS232

multiports, asynchronous multiplexers, asynchronous printer spoolers, etc.)

comprised of unshielded, twisted-pair wiring with RJ-45 connectors. It protects up to

four ports per unit.

Model PDIGTR (Digital Telephone Protection)

The PDIGTR module is only for use in T1, CSU, DSU, ISDN, DDS and Digital

Leased Line telecommunication equipment, TNV-1 or SELV circuits only.

General Installation

Safety

Caution: This equipment is intended to be used in a restricted access area and should only be

worked on by qualified service personal.

Please read and save these instructions and observe the following safety precautions.

•Use the system in a protected environment only.

•Never install telephone wiring during a lightning storm.

•Follow the installation instructions carefully. The current limiting feature in this product

could be rendered inoperable if the product is improperly installed.

Other Considerations

• Do not install this device in an environment where the operating temperature exceeds 0 to

40oC (32 to 104oF).

• Do not install this device where the relative humidity exceeds 95%, non-condensing.

• Do not store this device in an environment that exceeds 0 to 45oC (32 to 113oF).

Chassis Installation and Grounding

APC recommends that the ProtectNETTM Data Line Surge Protection chassis ( , Figure 1)

PRM24, be installed using the mounting hardware provided with the chassis. Additionally, the

chassis must be connected to a proper protective earth ground. A ground stud is provided on

the back of the chassis. Ensure the mounting rack or enclosure is connected to a proper ground.

Install the chassis and modules as shown in the illustration below.

Module Installation

The system chassis is designed to accomodate up to 24 data line modules. To install a module,

remove one of the blank panels by pulling it straight out from the chassis. Align the module

with the groove in the chassis, and slide the module fully into the chassis.

Cable Installation

To install a data line cable , connect the input RJ-45 connector to the signal source and then

to the upper connector on the module. Connect a data line cable from the lower connector on

the module to the equipment to be protected. Note: To accomodate 24 modules, the four-wide

center blank panel must be removed.

6 7

Ground

Stud / Wire

Produkspesifikasjoner

Merke:	Apc
Kategori:	Ikke kategorisert
Modell:	SYNX-980214

Trenger du hjelp?

Hvis du trenger hjelp med Apc SYNX-980214 still et spørsmål nedenfor, og andre brukere vil svare deg

Ditt navn*

Din e-post*

Skriv spørsmålet ditt her

Ikke kategorisert Apc Manualer

Apc PL5B-DE Bruksanvisning

16 Januar 2025

Apc SYNX-980214 Bruksanvisning

11 Desember 2024

Apc SYNX-3573406 Bruksanvisning

11 Desember 2024

Apc SBP3000RMHW Bruksanvisning

5 Desember 2024

Apc Smart-UPS SMT2200 Bruksanvisning

16 Oktober 2024

Apc Smart-UPS SMX3000LVNC Bruksanvisning

16 Oktober 2024

Apc P7GB Bruksanvisning

16 Oktober 2024

Apc P8VT3 Bruksanvisning

16 Oktober 2024

Apc SBP20KRMI4U Bruksanvisning

16 Oktober 2024

Apc GVSBPIT50 Bruksanvisning

16 Oktober 2024

Ikke kategorisert Manualer

Nyeste Ikke kategorisert Manualer

Amazfit Bip 5 Unity Bruksanvisning

16 Januar 2025

Lowepro Flipside Trek BP 350 AW II Bruksanvisning

16 Januar 2025

Audison Prima APS 8 D Bruksanvisning

16 Januar 2025

Black Line BLMH 36 Bruksanvisning

16 Januar 2025

Absco M 151151 Bruksanvisning

16 Januar 2025

ADDAC System ADDAC200CT Bruksanvisning

16 Januar 2025

Emerio LR-131325.1 Bruksanvisning

16 Januar 2025

Sony WRT-822B Bruksanvisning

16 Januar 2025

IKEA SMÅSPORRE 204.570.22 Bruksanvisning

16 Januar 2025

IKEA SÄFFEROT 904.570.71 Bruksanvisning

16 Januar 2025