AXESS AXAMP-FD3 Bruksanvisning

Les nedenfor 📖 manual på norsk for AXESS AXAMP-FD3 (4 sider) i kategorien Ikke kategorisert. Denne guiden var nyttig for 3 personer og ble vurdert med 4.5 stjerner i gjennomsnitt av 2 brukere

Side 1/4
AXAMP-FD3
I N S T A L L A T I O N I N S T R U C T I O N S
AxxessInterfaces.com © COPYRIGHT 2025 METRA ELECTRONICS CORPORATION REV. 1/30/25 INSTAXAMP-FD3
INTERFACE FEATURES
TOOLS & INSTALLATION ACCESSORIES REQUIRED
• Crimping tool and connectors, or solder gun,
solder, and heat shrink
• Tape
• Wire cutter
• Zip-ties
• Multimeter
TABLE OF CONTENTS
Installation & Installation Options 2 ........................
Adding Amp(s) to a Factory System 3 ....................
Troubleshooting.....................................................4
Designed for non-amplified vehicles
Provides 6 channels of 5-volt RMS audio
Non-fading full-range output (channels 5 and 6)
Simple plug-n-play installation behind the radio
No programming required
Dual-colored LED display
Input: 50W per channel
Amp turn on trigger (DC): 250mA
2-channel S/PDIF out (front)
APPLICATIONS
Visit for current application list
AxxessInterfaces.com
INTERFACE COMPONENTS
• AXAMP-FD3 Amplifier integration interface
• AXAMP-FD3 vehicle T-harness
• Bass knob
• LD-DSP-RPAD3
Amplifier Integration Interface
Fits Ford Select Models
2020-Up
www.MetraOnline.com
MetraOnline.com may be used to assist
with dash assembly instructions. Simply
enter your Year, Make, Model vehicle
into the vehicle fit guide and look for the
Dash Kit Installation Instructions.
ATTENTION: With the key out of the ignition,
disconnect the negative battery terminal before
installing this product. Ensure that all installation
connections, especially the air bag indicator lights, are
plugged in before reconnecting the battery or cycling
the ignition to test this product.
NOTE: Refer also to the instructions included with the
aftermarket accessory before installing this device.
2
Adding a full-range of amps and subwoofer to a factory system:
This feature offers the ability to add a full-range amp and sub to a factory system.
Note: The interface provides a 12-volt 1-amp output to turn on aftermarket amp(s). If installing
multiple amps, an SPDT automotive relay will be required if the amp turn-on current of all amps
combined exceeds 1-amp. Use Metra part number E-123 (sold separately) for best results.
1. Disassemble the dash, unplug all connectors, and then remove the factory radio.*
2. AXAMP-FD3 vehicle T-harness Install the to the vehicle and make all necessary
connections, but leave the amp turn-on wire disconnected.
3. AXAMP-FD3 vehicle T-harness AXAMP-FD3 interface Plug the to the .
4. AXAMP-FD3 interface harness AXAMP-FD3 interface Plug the to the .
5. Connect the amp turn-on wire.
6. Adjust your aftermarket amplifier to a desired listening level.
7. The Bassknob is used to adjust the output of channels 5 & 6 of the AXAMP.
Adjustment is as follows:
Counterclockwise turn lowers the volume of channels 5 & 6.
Clockwise turn raises the volume of channels 5 & 6.
*For dash disassembly instructions, refer to . Enter the year, make,
metraonline.com
and model of the vehicle in the and find instructions under Vehicle Fit Guide Metra
Radio Install kits.
INSTALLATION OPTIONS INSTALLATION
3
REV. 1/30/25 INSTAXAMP-FD3
ADDING AMPLIFIER/AMPLIFIERS TO A FACTORY SYSTEM

Produkspesifikasjoner

Merke: AXESS
Kategori: Ikke kategorisert
Modell: AXAMP-FD3

Trenger du hjelp?

Hvis du trenger hjelp med AXESS AXAMP-FD3 still et spørsmål nedenfor, og andre brukere vil svare deg




Ikke kategorisert AXESS Manualer

Ikke kategorisert Manualer

Nyeste Ikke kategorisert Manualer