AXESS AXSUB-FD3 Bruksanvisning

Les nedenfor 📖 manual på norsk for AXESS AXSUB-FD3 (4 sider) i kategorien Ikke kategorisert. Denne guiden var nyttig for 2 personer og ble vurdert med 4.5 stjerner i gjennomsnitt av 2 brukere

Side 1/4
I N S TA L L AT I O N I N S T R U C T I O N S
AXSUB-FD3
AxxessInterfaces.com © COPYRIGHT 2024 METRA ELECTRONICS CORPORATION REV. 3/5/24 AXSUB-FD3
• AXSUB-FD3 interface
• AXDSPX-FD3 vehicle T-harness (LD-DSP-FD3)
• Bass knob (LD-BASSKNOB)
INTERFACE FEATURES
FORD (Add a SUB) Interface
2018-UP
Visit AxxessInterfaces.com for more detailed informaon
about the product and up-to-date vehicle specic applicaons
INTERFACE COMPONENTS
Can be used in non-amplified models only
• Easy behind the radio installation with pre-wired harness
• Bass knob included for level control of subwoofer amp
• Micro-B USB updatable
www.AxxessInterfaces.com
www.MetraOnline.com
MetraOnline.com may be used to assist with
dash assembly instructions. Simply enter your
Year, Make, Model vehicle into the vehicle fit
guide and look for the Dash Kit Installation
Instructions.
If the vehicle is equipped with Active noise
cancelation (ANC) microphones, they will
need to be bypassed. Please refer to www.
Axxessinterfaces.com for ANC bypass
harnesses offered for select
vehicles.
TOOLS REQUIRED
TABLE OF CONTENTS
Connections.................................................................2
Programming..............................................................3
Testing..........................................................................3
Specifications...............................................................3
Troubleshooting..........................................................4
ATTENTION: With the key out of the ignition,
disconnect the negative battery terminal before
installing this product. nsure that all installation
connections, especially the air bag indicator
lights, are plugged in before reconnecting
the battery or cycling the ignition to test this
product.
NOTE: Refer also to the instructions included
with the aftermarket radio.
Crimping tool and connectors, or solder gun,
solder, and heat shrink • Tape • Wire cutter
Zip ties • Multimeter
*
*
2
CONNECTIONS
54-pin harness with loose
(White and White/Black) wires not used.
3
PROGRAMMING
REV. 3/5/24 AXSUB-FD3
TESTING
1. With everything plugged in Turn on ignition and make sure audio volume is turned all the
way down. Also ensure that your LD-BASSKNOB is turned all the way to the left.
2. Increase audio volume to desired listening level
3. Wait for aftermarket amp to turn on (up to 15 seconds)
4. You are now programmed
1. Turn on audio and increase volume to desired level
2. Rotate the LD-BASSKNOB to the right to increase SUB level. Turn to the left to decrease
SUB level
NOTE: Lowering the bass or volume knob completely will deactivate the aftermarket
amplifier. Similarly, muting the radio will also result in turning off the aftermarket amplifier.
SPECIFICATIONS
2 Channel non-fading 5V RMS output
Fixed low pass frequency of 234Hz
250mA remote turn on output

Produkspesifikasjoner

Merke: AXESS
Kategori: Ikke kategorisert
Modell: AXSUB-FD3

Trenger du hjelp?

Hvis du trenger hjelp med AXESS AXSUB-FD3 still et spørsmål nedenfor, og andre brukere vil svare deg




Ikke kategorisert AXESS Manualer

Ikke kategorisert Manualer

Nyeste Ikke kategorisert Manualer