Boss SB18BRGB Bruksanvisning

Boss Soundbar SB18BRGB

Les nedenfor 📖 manual på norsk for Boss SB18BRGB (2 sider) i kategorien Soundbar. Denne guiden var nyttig for 3 personer og ble vurdert med 4.5 stjerner i gjennomsnitt av 2 brukere

Last ned PDF

Side 1/2

Thank you for purchasing this

SB18BRGB Sound Bar

Please read through these instructions carefully so you will know

how to operate your model properly.

After you have nished reading the instructions, keep this document

in a safe place for future reference.

Before You Start

Read and understand all instructions before you use your product. If you do not follow the instructions

in this manual, we are not responsible for injury or damage resulting from improper handling. This will

also void the warranty.

Important Safety Precautions

• Be sure to observe the following guidelines:

- Do not increase speaker volume so high that you cannot hear what is around you.

- Use caution or temporarily discontinue use in potentially hazardous situations.

• Do not make any adjustment on the product when driving or in other situations where distractions can be

hazardous. Responsible and safe driving is your primary responsibility when operating a vehicle.

• Start volume at a low setting then gradually increase the volume until you can hear it comfortably, without

sound distortion and ear discomfort.

• In the event of smoke, strange noise or odor emitted from the product or any other abnormal operational

signs appearing on the product, disconnect the product from the power supply. Discontinue use and contact

your dealer or our technical support. Using the product in this condition may result in permanent damage to

the system.

• Servicing must only be carried out by a technician. Contact our technical support for any service questions.

Installation Precautions

• WARNING: Always consult a professional installer.

• Installation must be performed by a professional. Contact our technical support for any installation questions.

• Observe the safety and operating instructions of the devices which are connected to the product.

• Only use attachments/accessories specied by the manufacturer for installation.

• Do not modify this product, as this affects the safety of the product and creates a risk of injury.

• Before installation, disconnect the negative terminal of the vehicle battery to prevent damage to the product,

re, and/or possible injury.

Care for Your Product

• DO NOT clean the product in hot weather (e.g. hot sunlight).

• DO NOT use abrasive or highly alkaline cleaner on the product.

• DO NOT use gasoline, acetone, carbon tetrachloride or other aggressive chemical solutions on the product.

• DO NOT scrape the product with razor blade or other sharp instrument.

• DO NOT use a pressure washer or pressurized water.

• This product is water resistant. However, never submerge the product in water.

Mounting

Mounting on ATV or UTV

Always consult an expert when in doubt about the installation.

You must work with an assistant to mount the sound bar due to its heavy weight.

Use only the supplied accessory for mounting. Using other mounting methods may void the warranty.

To ensure security of the mounted sound bar, always check the mounting conditions (e.g. clamp

fastening) of the sound bar before each vehicle ride.

Spring washer

Upper clamp

Lower clamp

Rubber strip

Mounting bar

(Ø 1.75” − 2”)

Lower clamp

Sliding block

Power Connection

Option 1: Using Power Port

If your vehicle has a 12V power port, directly connect the sound bar to your vehicle for power connection.

1. Insert the 12V power port plug of the sound bar into your vehicle power port.

Note: To avoid battery drain, it is recommended to unplug after each use (if the port power is not switched

off with the ignition key).

To your vehicle power port

12V power port plug with 10A fuse

Option 2: Using Power Port Plug Adapter

If your vehicle dose not have a 12V power port, use the supplied power port plug adapter for connection to

your vehicle battery.

Important:

• To avoid short circuits and any resulting damage to the sound bar, the negative terminal of the vehicle battery

must be disconnected rst.

1. Connect the black/ground wire of the power port plug adapter to the vehicle’s metal frame or to the negative

battery terminal. Fasten the ground wire with a bolt/screw on the metal surface. Make sure the metal surface

is clean with no paint, rust or dirt.

2. Connect the red wire of the power port plug adapter to the positive battery terminal.

If needed, use extension wires of 12-14 gauge for connection to the battery. Remember to install a 15A

in-line fuse (not included) and an on/off switch (not included). An on/off switch is not needed if you

unplug the sound bar after each use or if the vehicle power port is turned off with the ignition key. Refer to

the illustration.

3. Insert the power port plug of the sound bar into the power port plug adapter.

THIS PACKAGE CONTAINS

1x SB18BRGB sound bar

Mounting kit + 1x Hex wrench

1x 12V power port plug adapter

1x Remote control + 1x Keychain

1x User manual + 1x Warranty card

IMPORTANT

Please enter below the Serial No. which is located on the exterior of the product. Retain this

information for future reference.

Model

Serial No.

Date of Purchase

Getting to Know Your Sound Bar

Introduction

The product is a Bluetooth speaker system which is ideal for installation in an ATV (All Terrain Vehicle) or UTV

(Utility Vehicle). You can stream audio from a mobile phone to this product via Bluetooth. You can also play music

les stored in a USB ash drive, and music from an external device (e.g. a mobile phone or MP3 player) can be

played via 3.5mm AUX input jack.

You can output audio from the sound bar to an external amplier or powered speakers through RCA output.

The product is integrated with LED lights which can be controlled using the supplied lighting controller.

This product is shockproof and water resistant. This product is designed to be operated with 10-16 VDC negative

ground vehicle power supply only. Never connect this product to any other voltage supply (e.g. 24 VDC).

Product Overview

1 2 3

1 3.5mm audio input jack

2 RCA audio output sockets

3 USB port

4 12V power port plug with 10A fuse

5 Power button (hold down to power on or off);

Mode button

6 Volume buttons

7 Start/pause/resume play button

8 Track selection buttons

9 Remote sensor (aim the remote control directly

at the sensor when using the remote controller)

10 Display

4 5 Power Connection

Vehicle’s metal frame

Black wire

12V power port plug with 10A fuse

Power port plug adapter

Red wire

Battery Fuse

(not included) 1

On/Off switch

(not included)

Option 3: Direct connection to vehicle battery

Important:

• To avoid short circuits and any resulting damage to the sound bar, the negative terminal of the vehicle battery

must be disconnected rst.

1. Remove the plug from the supplied power port plug cable.

2. Connect the power port plug’s negative wire to the vehicle’s metal frame or to the negative battery terminal,

and the power port plug’s positive wire to the positive battery terminal.

• To prevent electrical damage, you must install 1) a 15A fuse (not included) and 2) an on/off switch (not

included) to be in line with the power wire which connects to the positive battery terminal.

• Fasten the ground wire with a bolt/screw on the metal surface. Make sure the metal surface is clean with no

paint, rust or dirt.

Turn on or off

• Press and hold on the sound bar (or on the remote control) to turn on or off the sound bar. When turned

on, the power LED indicator illuminates on the power port plug.

• on the remote control to turn on or off the LED lights.Press briey

To avoid battery drain when the sound bar is not used, disconnect the sound bar from the battery by

unplugging the power port plug or using the inline on/off switch (not included).

1. Correctly orient the supplied sliding block, and attach

it to the bottom side of the lower clamp using the

supplied hex wrench. Make sure not to tighten the

block for subsequent slide into the groove.

2. Find the groove on the top panel of the sound bar.

Correctly orient the sliding block and slide it into the

groove from either end of the groove. Then slide the

clamp to a proper position and tighten it with the hex

wrench.

3. Attach the supplied rubber strips over the clamp and

cage bar for secure clamping and abrasion prevention.

4. Tighten the upper clamp to the lower clamp with the

hex wrench. Make sure the supplied spring washers

are used to provide more stable bolt fastening against

vibration.

Repeat the steps above to secure the sound bar with

the other clamp assembly.

SB18BRGB

0823

Bluetooth

Before you can stream music from your mobile device (iOS device or Android device) to the sound bar through

Bluetooth, pair the sound bar with your mobile device.

1. The sound bar automatically switches to Bluetooth mode when turned on. “bt” appears and ashes to

indicate that the sound bar enters pairing mode.

If Bluetooth mode is not activated, press MODE briey to select Bluetooth mode.

2. On your mobile device, enable Bluetooth function and select the device name (“Boss Audio SB18BRGB”) to

pair the sound bar with the mobile device. If prompted for password, enter “0000”.

If no Bluetooth device is paired within ten minutes, the sound bar will automatically exit pairing mode. In this

case, you need to repeat the steps above to re-enter the pairing mode.

Note: Only one device can be paired at a time.

3. When successfully paired/connected, “bt” on the display stops ashing and lights up. Play audio on your

mobile device, and audio will be streamed to the sound bar.

After pairing, the sound bar will be automatically connected to your mobile device each time the two are

turned on. To change Bluetooth source, disconnect the current Bluetooth connection by holding down for

two seconds then repeat the steps above to connect/pair with another mobile device.

11Playback control

• To pause or resume play, press .

• To select the previous or next track, press or .

• To adjust volume, press .VOL +/-

To maximize audio performance, set the volume of the connected device to a minimum of 75%.

Ideally, on the highest volume setting you can get without distortion.

To avoid battery exhaustion, make sure to run the vehicle engine when operating the sound bar.

Operational range can be reduced by any obstacle between the sound bar and the device.

If the connected device is out of the effective range from the sound bar, the device will be automatically

disconnected. The device will be automatically re-connected if it is back to the effective range.

7AUX

You can listen to an external audio device (e.g. MP3 player or a mobile phone) through the sound bar.

3.5mm

audio cable

AUX

input

1. Using an audio cable with 3.5mm plug (not included), connect the AUX input (3.5 mm) from the sound bar

to the headphone jack on your audio device.

2. The sound bar automatically switches to AUX mode when AUX connection is made. “AUX” is displayed.

If AUX mode is not activated, press briey to select AUX mode.MODE

3. Select and play audio les on your audio device. Audio from the connected device will be played on the

sound bar.

To maximize audio performance, set the volume of the connected device to a minimum of 75%.

Ideally, on the highest volume setting you can get without distortion.

Operating the sound bar consumes the vehicle battery. To avoid battery exhaustion, make sure to run

the vehicle engine when operating the sound bar.

12Playback control

• To pause or resume play, press .

• To adjust volume, press .VOL +/-

• To select the previous or next track, use the controls only on the connected device.

USB

You can enjoy audio stored on a USB storage device through the sound bar.

USB ash drive

USB port

1. Connect a USB ash to the USB port from the sound bar.

2. The sound bar automatically switches to USB mode when USB connection is made. “USB” is displayed

briey.

If USB mode is not activated, press MODE briey to select USB mode.

Music plays automatically.

MP3 and WMA les are playable. The USB port can provide 1A current for mobile device charging.

Operating the sound bar consumes the vehicle battery. To avoid battery exhaustion, be sure to run the

vehicle engine when operating the sound bar.

13Playback control

• To pause or resume play, press .

• To select the previous or next track, press or .

• To adjust volume, press .VOL +/-

Audio Output

You can output audio from the sound bar to an external amplier or powered speakers through RCA output.

RCA output sockets

Audio cable with RCA plugs

Fuse Replacement

If the power LED indicator on the power port plug does not illuminate, this indicates the fuse inside the power port

plug is blown. Replace the blown fuse with a new 10A AGC fuse (glass cartridge type).

1. Locate the screw cap on the front end of the power port plug. Turn counterclockwise the screw cap to open

then access the fuse inside.

2. Replace with a new fuse (not included). Then replace the power port plug while ensuring the contact head

sticks out.

Screw cap and contact head AGC fuse

Remote Control

The sound bar comes with a remote control. You can use the remote control to control both music playback

and the LED lights which are integrated with the sound bar.

Light control buttons

1Press and hold to turn the sound bar

on or off.

Press briey to turn lights on or off.

2MODE +/- Switch from static to dynamic illumination

and select a dynamic illumination pattern.

3SPEED +/- For dynamic illumination, select a dynamic

illumination speed.

4DEMO Cycle red, green and blue illumination.

5COLOR +/- Switch from dynamic to static illumination

and select an illumination color.

6BRIGHT +/- For static illumination, change the

illumination intensity.

7SYN Enable or disable lights ashing to music.

When enabled, SPEED buttons are invalid.

Playback control buttons

A / For Bluetooth and USB, select the

previous or next track.

BVOL +/- Increase or decrease volume.

CEQ For Bluetooth and USB, select a preset

sound mode.

DStart, pause or resume music play.

EMODE Select a mode (Bluetooth, AUX and USB).

CR2025 battery

replacement

Troubleshooting

If you have problems using this product, check the following points before you request service. If you still have

a problem, contact our technical support.

Problem Solution

Power off after beeping 3 times.

If the voltage runs below 8.5V or above 18.5V, the sound bar

will beep 3 times then automatically turn off to prevent battery

depletion or voltage-surge damage.

No power.

Power connection is not made. See the section “Power

Connection” for details.

The fuse inside the power port plug is blown. Replace the fuse.

The ACC switch of the vehicle is not on. Turn the ACC switch on.

No sound.

Press to select the correct audio input. MODE

Check the connected device for volume level or playback status

(e.g. pause or stop).

Cannot connect through Bluetooth.

The device is not paired with the sound bar. Pair the two (see

“Bluetooth” section).

Make sure the device is within range.

The sound bar is already connected with another Bluetooth

device. Disconnect the current Bluetooth connection.

Bluetooth has been disconnected for more than three minutes,

manually reconnect Bluetooth through your mobile device.

Audio quality from Bluetooth

connection is poor.

Move the device closer to the sound bar or remove obstacles or

sources of interference that are affecting Bluetooth reception.

No response. Power glitch or interference. Disconnect power for ten seconds

then reconnect power.

Environmental Care

Do not throw away the product with normal household waste at the end of its life. Follow your local laws if/

when disposing of electronic products. By doing this, you help preserve the environment.

8 9 10

11 12

Using an audio cable with RCA plugs

(not included), connect RCA sockets

from the sound bar to RCA inputs on an

amplier or powered speakers.

1Important notes on battery

• Observe correct polarity while inserting the battery. Replace only with the same type or equivalent type.

• Do not leave the battery under direct sunlight. This may cause re, explosion or excessive heat.

• Remove the battery from the remote control if not used for a long period of time.

• The remote control contains a coin/button type battery, which is a choke hazard. Keep the battery out of reach

of children at all times! If swallowed, the battery can cause serious injury or death.

Specications

Bluetooth

Bluetooth version ..............................................5.0 / EDR

Bluetooth proles A2DP, AVRCP ..............................................

Bluetooth frequency ..........................................2402 - 2480 MHz

Transmission power..........................................<4 dBm

Transmission distance ......................................up to 33 ft /10 m (line of sight)

Speakers

High power speaker .........................................2 x 4” (102 mm)

Tweeter .............................................................2 x 1” (25 mm), soft dome

Amplier

Amplier class ..................................................Class A/B, full range

Input impedance ...............................................10 kΩ

Frequency response .........................................45 Hz - 22 kHz

Connectivity

USB .................................................................. USB-A, MP3/WMA playable; USB charging (1A)

AUX 3.5 mm jack for audio input ..................................................................

RCA RCA sockets for audio output .................................................................

General

Input voltage ..................................................... 12 VDC (allowable 10 - 16 VDC)

Current draw .....................................................6A MAX

Fuse ..................................................................10A AGC type

Clamp size range (O.D.) ...................................1.75” - 2”

Weight ..............................................................8.2 lbs / 3.7 kg

Dimensions drawing

18”

(458 mm) (95 mm)

3.74”

4.88”

(124 mm)

4.88”

(124 mm)

Produkspesifikasjoner

Merke:	Boss
Kategori:	Soundbar
Modell:	SB18BRGB

Trenger du hjelp?

Hvis du trenger hjelp med Boss SB18BRGB still et spørsmål nedenfor, og andre brukere vil svare deg

Ditt navn*

Din e-post*

Skriv spørsmålet ditt her

Soundbar Boss Manualer

Boss SB18BRGB Bruksanvisning

12 Desember 2024

Soundbar Manualer

Nyeste Soundbar Manualer

Boston Acoustics TVee 20 Bruksanvisning

15 Desember 2024

Boston Acoustics TVee 25 Bruksanvisning

15 Desember 2024

Dell AX510 Bruksanvisning

10 Desember 2024

Nedis SPSB420BK Bruksanvisning

10 Desember 2024

Muse M-1680 SBT Bruksanvisning

10 Desember 2024

Trust Thorne GXT 619 Bruksanvisning

7 Desember 2024

Memphis Audio MXSB24V3 Bruksanvisning

26 Oktober 2024

Samsung HW-S701D Bruksanvisning

26 Oktober 2024

Aiwa HE-950BT Bruksanvisning

24 Oktober 2024

TCL S45H Bruksanvisning

24 Oktober 2024