Cobra ACXT360 Bruksanvisning

Cobra Radio ACXT360

Les nedenfor 📖 manual på norsk for Cobra ACXT360 (2 sider) i kategorien Radio. Denne guiden var nyttig for 3 personer og ble vurdert med 4.5 stjerner i gjennomsnitt av 2 brukere

Last ned PDF

Side 1/2

Battery Low

When battery power is low, the nal bar in the

Battery Low icon will blink and an audible tone will

sound twice before the radio shuts off. Your batteries

should be replaced or recharged, if using

rechargeable batteries.

Auto Battery Save

If there are no transmissions within 10 seconds, the

radio will automatically switch to mode Power Save

and the icon will ash in the display. Power Saver

This will not affect the radio’s ability to receive

incoming transmissions.

Communicating with Another Person

Press and hold the button.1. Talk

With the microphone about two inches (5 cm) from 2.

your mouth, speak in a normal voice.

Release the button when you are 3. Talk

nished talking and listen for a response.

You cannot receive incoming calls while

pressing the button.Talk

To Select a Channel

With the radio , select any of the 22 channels by on

pressing the or button. Channel Up Channel Down

To temporarily turn off auto squelch:

Press the button for Light/Max Range

less than ve seconds.

To turn maximum range extender on:

– Press and hold the button Light/Max Range

for at least ve seconds until you hear

two beeps which indicates the maximum

range extender is .on

To turn maximum range extender off:

– Press and release the Light/Max Range

button or change channels.

Lock Function

The Lock Channel Up, Channel function locks the

Down and buttons to prevent Mode/Power

accidental operation.

To turn the lock on or off:

– Press and hold the button for Lock

two seconds.

A double beep sound is used to conrm your lock on

or off Lockrequest. When in mode,

the Lock icon will be displayed.

microTALK® Range

Your range will vary depending on terrain and conditions.

In at, open country your radio will

operate at maximum range.

Buildings and foliage in the path of the

signal can reduce the range of the radio.

Dense foliage and hilly terrain will further

reduce the range of the radio.

On FRS Channels 8 through 14, your radio

automatically switches to low power, which

will limit the range the radio can communicate.

Turning on Your microTALK® Radio

Press and hold the button until you hear a Mode/Power

series of audible tones indicating the radio is on. Your

microTALK® radio is now in mode, ready to Standby

receive transmissions. The radio is always in Standby

mode except when the or Talk, Call Mode/Power

buttons are pressed.

Battery Status Indicator

The battery charge status is shown on the display.

Four bars indicates fully charged.

Insert Batteries

Ra io Char er Jacd g k

Staying in touch with your family and friends is convenient

and easy when using your microTALK

® radio. Some of the

many uses you will discover include:

Communicating with others while hiking, biking, and working; keeping track of

family and friends at a crowded public event; checking with travel companions

in another car; talking with neighbors; arranging meeting spots with others

while shopping at the mall.

Secure your microTALK

radio while on the go.

Carrying your microTALK® radio with you is easy when

using the belt clip or optional wrist strap.

The belt clip easily attaches to your belt, purse, or

backpack.

Owner’s Manual

Introduction

M ing Liak fe Easier an Sa d fer

Introduction

Product Features

Operation

Using Your Radio

Customer Assistance

Product Service & Support

Belt Clip

Back itl LCD Disp yla

Features

• 22 Channels

• 10 Channel NOAA All

Hazards Radio

• Weather Alert

• 121 Privacy Codes

(38 CTCSS codes/

83 DCS codes)

• Hands-Free Operation

(VOX)

• Scan

Channels, privacy

codes

• Backlit LCD Display

• Call Alert

Five selectable tones

• Button Lock

• Speaker/

Microphone/

Charge Jack

• Roger Beep

Selectable On/Off

• Battery/Power Saver

• Keystroke Tones

• Battery Level

Indicator

• Auto Squelch

• Maximum

Range Extender

• Belt Clip

Printed in China

Part No. KEM-ML39900A

English

TWO-WAY R O L ADI MODE

ACXT360

Nothing Comes Close a brato Co ®

For any questions about operating this new Cobra branded product, PLEASE

information for support will vary depending on the country in which you

purchased and utilize the product.

To obtain warranty service or other information for products purchased from

Altis itself or through its authorized reseller or agent and utilized in the U.S.A.,

please call our consumer support line at , or email us at (866) 721-3805

support@altistec.com. You will receive instructions on how to ship the

products at your expense to an Altis Global Limited Authorized Service Center.

To obtain service, you must include: (a) a copy of your receipt, bill of sale or

other comparable proof of purchase; (b) a written description of the problem;

and, most importantly; (c) your address and telephone number.

For warranty and customer service information outside the US, please contact

your local dealer.

For further information needed on its features,

please visit www.cobrawalkietalkie.com

for frequently asked questions and the

electronic manual.

A-1 A-2 A-3 1

Remove Belt Clip

Pull Up Lock hLatc

Caring for Your microTALK

® Radio

Your microTALK

® radio will give you years of trouble-free service

if cared for properly. Handle the radio gently. Keep the radio away from dust.

Never put the radio in water or in a damp place. Avoid exposure to extreme

temperatures.

Installing Batteries

To install or replace batteries:

1. Remove belt clip by releasing belt clip

latch and sliding clip up.

2. Pull up on the battery door latch to remove the

battery compartment cover.

3. Insert the supplied three AA rechargeable

batteries or non-rechargeable alkaline batteries.

Position batteries according to polarity markings.

4. Replace battery compartment cover and

belt clip.

• Do not attempt to charge alkaline batteries.

• Do not mix old and new batteries.

• Do not mix alkaline, standard (carbon-zinc), or

rechargeable (Ni-Cd, Ni-MH, etc.) batteries.

To charge batteries in radio:

1. Check to see that the batteries have been

inserted properly.

2. Insert the cable into the charge jack located at

the top of the radio.

3. Plug the cable into USB-compatible power port.

Use only the supplied rechargeable batteries and charger for recharging

your Cobra microTALK

® radio.

Cobra recommends your radio is turned off while being charged.

Non-rechargeable alkaline batteries can also be used in your radio.

2 3 4 5 6

Mode/Power

Channel Button

Call Button

Lock Button

Battery Charge

Status

Quick Start

1. Mode/Power Press and hold the button

to turn your radio.on

2. Channel Up Channel Down Press the or

button to select a channel.

3. Talk Press and hold the button while

speaking into the microphone.

4. Talk When nished talking, release the

button and listen for a response.

Both radios must be tuned to the same

channel/privacy code to communicate.

Battery Low

Battery Save Mode

Talk Button

Two nches cm I (5 )

fr M hom out

Channel Number

Both radios must be tuned to the

same channel to communicate.

The radio will display ashing battery icon

while charging if the radio is on.

Both radios must be tuned to the

same channel to communicate.

See for frequency allocations chart.page 13

Listening

Volume Level

Light/Max Range

Listening for a Response

Release the button to receive incoming Talk

transmissions. Your microTALK

® radio is always

in Standby Talk Call mode while the or buttons

are not pressed.

To Adjust Volume

Press the or Volume Up Volume

Down button.

A double beep sound is used to indicate

the minimum and maximum volume levels

(1 through 8).

Call Button

Press and release the button. Call

The other person will hear a three second call

tone. This tone is used only to establish voice

communications.

To Illuminate Display

Press and release the button Light/Max Range

to illuminate the display.

Auto Squelch/Maximum Range

Your microTALK

® radio will automatically shut off weak transmissions

and unwanted noise due to terrain, conditions or if you’ve reached your

Maximum Range limit.

You can temporarily turn auto squelch or turn maximum range off on

extender, allowing all signals to be received and extending the

maximum range of your radio.

See page 11 on how to select between

ve call tone settings.

Lock Icon

Maximum Range

Reduced Range

Remember, you can achieve maximum

range by using maximum range extender.

See page 4 for details.

Scrolling Through the Mode Function

By scrolling through the function, you will be able to Mode

select or turn preferred features of your microTALKon ® radio. When

scrolling through the function, your radio features Mode

will be displayed in the same predetermined order:

Set CTCSS Privacy Codes

Set DCS Privacy Codes

Set Vox On/Off

Set Vox Sensitivity

Set Channel Scan

Set CTCSS Privacy Code Scan

Set DCS Privacy Code Scan

Set Call Tones

Set Roger Beep On/Off

Privacy Codes

Your microTALK

® radio incorporates two advanced coded squelch

systems that can help to reduce interference from other users

on any given channel. CTCSS (Continuous Tone Coded Squelch

System) provides 38 privacy codes and DCS (Digitally Coded Squelch)

provides 83 privacy codes. This provides a total of 121 Privacy

Codes. Either system can be used on all channels, but both systems

cannot be used on the same channel at the same time.

To successfully communicate using a privacy code, both

the sending and receiving radios must be tuned to the same

channel and to the same privacy code system (CTCSS or DCS)

and privacy code number. Each channel will remember the

last privacy code system and number you select.

The privacy code 00 is not a privacy code, but allows all

signals to be heard on a channel that is set to 00 on both

the CTCSS and DCS systems.

Atlanta, GA USA.

www.cobrawalkietalkie.com

Mode Functions (continued on back side)

Maximum range may vary and is based on

unobstructed line-of-sight communication

under ideal conditions.

1. Antenna

2. External Speaker/

Microphone/Charge Jack

3. ButtonMode/Power

4. ButtonWeather/Lock

5. Buttons Channel Up/Down

6. Backlit LCD Display

7. Speaker/Microphone

8. ButtonsVolume Up/Down

9. ButtonLight/Max Range

10. ButtonTalk

11. ButtonCall

12. Wrist Strap Connection

13. Belt Clip

14. Battery Compartment

15. Battery Door Latch

1. Battery Level Indicator

2. VOX Icon

3. Scan Icon

4. Roger Beep Icon

5. Lock Icon

6. Low Power Icon

7. DCS/CTCSS Icons

8. Weather Icon

9. Weather Alert Icon

10. DCS/CTCSS Privacy Code Numbers

11. Power Saver Icon

12. Channel Numbers

13. Receive/Transmit Icon

Operation

Mode Functions

23 4 5

Volume Button

NOAA* All Hazards Radio Channels

You can use your microTALK® radio to listen to NOAA All Hazards Radio

channels transmitting in your area.

To listen to All Hazards Radio channels:

Press the button until the 1. Weather All Hazards

Radio icon and the currently selected All Hazards

Radio channel are displayed.

Use the or 2. Channel Up Channel Down

button to change All Hazards Radio channels.

The icon will continue to 3. All Hazards Radio

be displayed when is on. All Hazards Radio

To exit , press and hold the4. All Hazards Radio

Weather button.

*National Oceanographic and Atmospheric Administration

Weather (WX) Alert Mode

Turning the function will allow your radio to On Weather Alert

automatically receive NOAA Hazard Alert radio signals and warnings from

designated NOAA broadcast stations. If the radio is turned ON, it will alert

to Weather and other emergency alerts broadcast by NOAA.

To turn Weather Alert On or Off:

Press the button until the Weather1. Weather/Lock

Alert icon ashes on the display. The current On

or Off setting is displayed.

Press the and button2. Channel Up Channel Down

to turn Weather Alert or .On Off

Press and hold the button again to3. Weather/Lock

save the new setting and exit the Weather Alert

Mode Standby and return to mode.

Warranty & Trademark Acknowledgment

Operation

General Specications

8 9 10 11

12 13 14 15 16

Privacy Code

If DCS is turned on at the channel

selected, the display will ash the

CTCSS icon and “OFF.” To switch from

DCS to CTCSS, press the Channel Up

or button while the displayChannel Down

is ashing “OFF.” The display will then

show the small numbers ashing and you

will then be able to proceed to step 2.

Operation

Mode Functions (continued)

Mode/Power

Weather Button

Scan Channels

Channel Scan

Your microTALK

® radio can automatically scan channels.

To scan channels:

Press the button until the 1. Mode/Power

Scan icon and the channel numbers appear

on the display.

Press the or button to2. Channel Up Channel Down

begin scanning channels.

The Scan icon will continue to be displayed when

scan is . Your radio will continue to scan allon

channels and stop if an incoming transmission is

detected. Your radio will remain on that channel for

10 seconds.

During scanning (while receiving an incoming transmission),

you can choose from the following:

Press and hold the button to communicate on that channel.a. Talk

Your radio will remain on that channel and return to mode.Standby

Press the or button to resume b. Channel Up Channel Down

scanning channels.

Press the button to return to .c. Lock Standby

During scanning (while receiving an incoming transmission),

you can choose from the following:

Press and hold the button to communicate on that channel/a. Talk

privacy code. Your radio will remain on that channel/privacy code

and return to mode.Standby

Press the or button to b. Channel Up Channel Down

resume scanning privacy codes. If you do not press any button

within 10 seconds, your radio will automatically resume scanning

privacy codes.

Press the button to return to .c. Lock Standby

The radio ignores specic privacy

codes while scanning channels.

Select Channel

Scan Pr vacy Co i des

Privacy Code Scan

Your microTALK® radio can automatically scan the (eitherPrivacy Codes

CTCSS 01 through 38 or DCS 01 through 83) within one channel. Only

one set of privacy codes (CTCSS or DCS) can be scanned at a time.

To scan privacy codes:

While in mode, press the or1. Standby Channel Up

Channel Down button to choose the channel on

which you wish to scan privacy codes.

Press the button until either the2. Mode/Power

CTCSS or the DCS icon appears on the display

and the icon and the privacy code numbersScan

ash on the display.

Press the or button3. Channel Up Channel Down

to begin scanning privacy codes within the

channel you selected.

During scanning (while receiving an incoming transmission),

you can choose from the following:

Press and hold the button to communicate on that channel/a. Talk

privacy code. Your radio will remain on that channel/privacy code

and return to mode.Standby

Press the or button to b. Channel Up Channel Down

resume scanning privacy codes. If you do not press any button

within 10 seconds, your radio will automatically resume scanning

privacy codes.

Press the button to return to .c. Lock Standby

Hazards Radio Icon

This feature is set

to by default.OFF

Make sure the strongest

Weather channel is selected

for your area using the NOAA

All Hazards Radio Channels

selection in the previous menu.

General ecic io Sp at ns

FRS/GMRS Frequenc ll cat any A o ion d Comp ity at ilib

A = Channel No. for 22 Channel FRS/GMRS Models

B = Frequency in MHz

C = Power Output

A B C

1 462.5625 High

2 462.5875 High

3 462.6125 High

4 462.6375 High

5 462.6625 High

6 462.6875 High

7 462.7125 High

8 467.5625 Low

9 467.5875 Low

10 467.6125 Low

11 467.6375 Low

12 467.6625 Low

13 467.6875 Low

14 467.7125 Low

15 462.5500 High

16 462.5750 High

17 462.6000 High

18 462.6250 High

19 462.6500 High

20 462.6750 High

21 462.7000 High

22 462.7250 High

MODEL ACXT360:

This device complies with part 15 of the FCC Rules. Operation is subject to the following

two conditions: 1) This device may not cause harmful interference, and 2) this device

must accept any interference received,including interference that may cause undesired

operation.

FCC Warnings: Replacement or substitution of transistors, regular diodes or other parts

of a unique nature, with parts other than those recommended by Cobra may cause a

violation of the technical regulations of part 95 of the FCC rules, or violation of type

acceptance requirements of part 2 of the rules.

Limited One-Year Warranty

Altis Global Limited warrants to the original consumer purchaser only that this product and

the component parts thereof, will be free from defects in workmanship and materials for a

period of one year from the date of rst consumer purchase. During this period, Altis will,

repair or replace, at its sole option and discretion, this product or any defective parts. Altis’

liability hereunder shall be limited to repair or replacement of the defective part or parts,

and such correction shall constitute a fulllment of all of Altis’ warranties hereunder.

This limited warranty is only valid for the original consumer purchaser in limited

jurisdictions and is not transferrable. This limited warranty will automatically terminate

prior to expiration if this product is sold or otherwise transferred to another party. The

product must be purchased from Altis or an authorized dealer or the warranty is void. This

limited warranty is valid only for products purchased and utilized in specic jurisdictions.

Please visit our website at for a list of jurisdictions wherein www.cobrawalkietalkie.com

this limited warranty is valid.

This limited warranty does not cover damage due to misuse, abuse, negligence, acts of

God, accident, commercial use or modication of, or to any part of this product. This

warranty does not cover damage due to improper operation, maintenance or installation;

ordinary wear and tear; or attempted alterations or repairs by anyone other than Altis or

someone authorized by Altis to do warranty work. Any unauthorized alterations or repairs

will void this warranty. This limited warranty does not cover product sold AS IS or WITH ALL

FAULTS. This limited warranty is invalid if the factory applied serial number or date stamp

has been altered, defaced or removed from this product. This limited warranty does not

cover product purchased or utilized in a jurisdiction not covered.

The procedure for obtaining service and support, and the applicability of this warranty, will

vary depending on the country or juristiction in which you purchase and utilize the product.

For details on obtaining product service, support and other warranty information please visit

www.cobrawalkietalkie.com.

This warranty gives you specic legal rights, and you may also have other rights which vary

from state to state and country to country.

EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, ALTIS MAKES NO OTHER

WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. ALTIS EXPRESSLY

DISCLAIMS ALL WARRANTIES NOT STATED IN THIS LIMITED WARRANTY. ANY IMPLIED

WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED TO THE TERMS OF THIS

EXPRESSED WARRANTY.

LIMITATION OF REMEDIES AND DAMAGES. REPAIR OR REPLACEMENT AS PROVIDED

UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER. ALTIS SHALL

NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT

LIMITED TO ATTORNEYS’ FEES AND/OR COSTS OF LITIGATION, FOR BREACH OF ANY

EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT. ALTIS IS NOT LIABLE FOR ANY

DAMAGES CAUSED BY THE PRODUCT OR BY THE PRODUCT TO PERFORM, INCLUDING ANY

DCS Privacy Code

VOX Icon

If CTCSS is turned at the channel selected, on

the display will ash the DCS icon and “OFF.”

To switch from CTCSS to DCS, press the

Channel Up Channel Down or button while

the display is ashing “OFF.” The display will

then show the small numbers ashing and

you will then be able to proceed to step 2.

VOX Sens itivity lLeve

The current VOX sensitivity level is

displayed with letters “L” and a Number 1

through 5, with Number 5 being the most

sensitive level and Number 1 being the

least sensitive level.

Channel Button

Mode/Power

Set CTCSS Privacy Codes

To select a CTCSS privacy code:

After selecting a channel, press the 1. Mode/Power

button until the icon appears and the small CTCSS

numbers next to the channel number ash on the

display.

2. Channel Up Channel Down Press using the or button to select a privacy

code. You can hold the or button for fast advance.Up Down

3. When your desired CTCSS privacy code is displayed, choose one of the

following:

Press the button to enter the new setting and proceed to a. Mode/Power

other functions.

Press the button to return to mode.b. Lock Standby

Do not press any buttons for 15 seconds to return to mode.c. Standby

Set DCS Privacy Codes

To select a DCS privacy code:

After selecting a channel, press the 1. Mode/Power

button until the DCS icon appears and the small

numbers ash on the display (00 through 83).

2. Channel Up Channel Down Press using the or button to select a DCS

privacy code. You can hold the or button for fast advance.Up Down

3. When DCS privacy code is displayed, choose one of the following:

Press the button to enter the new setting and proceed to a. Mode/Power

other functions.

Press the button to return to mode.b. Lock Standby

Do not press any buttons for 15 seconds to enter the new settings and to c.

return to mode.Standby

Voice Activated Transmit (VOX)

In VOX mode, your microTALK

® radio can be used “hands-free,” automatically

transmitting when you speak. You can set the sensitivity level to t the volume VOX

of your voice and avoid transmissions triggered by background noise.

To turn VOX mode on or off:

Press the button until the icon 1. Mode/Power VOX

ashes on the display. The current or setting is On Off

displayed.

Press the or button to turn 2. Channel Up Channel Down

VOX or On Off.

Choose one of the following:3.

a. Mode/Power Press the button to enter the new

setting and proceed to other functions.

b. Lock Standby Press the button to return to mode.

To set VOX sensitivity:

1. Mode/Power VOX Press the button until the icon

ashes and the current sensitivity level is displayed.

2. Channel Up Channel Down Press the or button to

change the setting.

3. Choose one of the following:

Press the button to enter the selected a. Mode/Power

setting and proceed to other functions.

Press the button to return to mode.b. Lock Standby

Call Tone Setting

Roger Beep Off

Five Call Tone Settings

You can choose between ve different to transmitCall Tone Settings

a call alert.

To change a call tone setting:

Press the button until the 1. Mode/Power

letter “C” and the current call tone number

(01 through 05) is displayed. The current

call tone will sound for one second.

Press the or button2. Channel Up Channel Down

to hear the other call tone settings.

Choose one of the following:3.

a. Mode/Power Press the button to

enter the new setting and proceed

to other functions.

b. Lock Standby Press the button to return to

mode.

Roger Beep Conrmation Tone

Your listener will hear an audible tone when you release the

Talk button. This alerts the other party that you are nished

talking and it is OK for them to speak.

To turn roger beep on or off:

Press the button until the 1. Mode/Power

Roger Beep icon ashes. The current

on off or setting is displayed.

Press the or button2. Channel Up Channel Down

to select roger beep or .on off

Choose one of the following:3.

a. Mode/Power Press the button to

return to .Standby mode

b. Lock Standby Press the button to return to

mode.

Channel Button

Mode/Power

LOST PROFITS, LOST SAVINGS, INCIDENTAL DAMAGES, OR CONSEQUENTIAL DAMAGES.

ALTIS IS NOT LIABLE FOR ANY CLAIM MADE BY A THIRD PARTY OR MADE BY YOU FOR A

THIRD PARTY. THIS LIMITATION APPLIES WHETHER DAMAGES ARE SOUGHT, OR A

CLAIM MADE, UNDER THIS WARRANTY OR AS A TORT CLAIM (INCLUDING NEGLIGENCE

OR STRICT PRODUCT LIABILITY), A CONTRACT CLAIM, OR ANY OTHER CLAIM. THIS

LIMITATION CANNOT BE WAIVED OR AMENDED BY ANY PERSON. THIS LIMITATION OF

LIABILITY WILL BE EFFECTIVE EVEN IF ALTIS OR AN AUTHORIZED REPRESENTATIVE OF

ALTIS HAS BEEN ADVISED BY YOU OF THE POSSIBILITY OF ANY SUCH DAMAGES.

Some states and countries do not allow limitations on how long an implied warranty lasts

and do not allow the exclusion or limitation of incidental or consequential damages, so

the above limitations may not apply to you. This warranty gives you specic legal rights,

and you may also have other rights which vary from state to state and country to

country.

Provided that the product was purchased from Altis itself or through its authorized

reseller or agent and utilized in the U.S.A., Altis will, without charge, repair or replace, at

its option, defective products, products or component parts upon delivery to the

authorized Altis Global Limited Authorized Service Center, accompanied by proof of the

date of rst customer purchase, such as a duplicated copy of a sales receipt.

You must pay any initial shipping charges required to ship the product for warranty

service, but the return charges, to an address in the U.S.A, will be at Altis’ expense, if the

product is under warranty.

For Products Purchased Outside The U.S.A.

Please contact your authorized local reseller or agent for warranty information.

Trademark Acknowledgment

Manufactured, distributed, or sold by Altis Global Limited, ofcial licensee for this

product. Cobra®, microTalk®, Nothing Comes Close to a Cobra®, and the snake design

are registered trademarks of Cobra Electronics Corporation, USA. Cobra Electronics

Corporation™ is a trademark of Cobra Electronics Corporation, USA. All other product or

service names are the property of their respective owners.

IMPORTANT NOTICE:

WARNING: Changes or modications to this unit not expressly approved by the party responsible

for compliance could void the user’s authority to operate the equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two

conditions: 1) This device may not cause harmful interference, and 2) this device must accept any

interference received,including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates, uses

and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/TV technician for help.

Safety Information for microTALK Radios

Your wireless handheld portable transceiver contains a low power transmitter. When the talk button

is pushed, it sends out radio frequency (RF) signals. The device is authorized to operate at a duty

factor not to exceed 50%. In August 1996, the Federal Communications Commissions (FCC) adopted

RF exposure guidelines with safety levels for handheld wireless devices

Important

FCC RF Exposure Requirements: For body-worn operation, this radio has been tested and meets the

FCC RF exposure guidelines when used with Cobra accessories supplied or designated for this

product. Use of other accessories may not ensure compliance with FCC RF exposure guidelines. Use

only the supplied antenna. Unauthorized antennas, modications or attachments could damage the

transmitter and may violate FCC regulations.

Normal Position

Hold the transmitter approximately 2 inches from your face and speak in a normal voice, with the

antenna pointed up and away.

FCC Part 15.21 Warning Statement-

NOTE: THE GRANTEE IS NOT RESPONSIBLE FOR ANY CHANGES OR MODIFICATIONS NOT

EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE. SUCH MODIFICATIONS

COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.

IC RSS-GEN

This device complies with ISEDC license-exempt RSS standard(s). Operation is subject to the

following two conditions: (1) this device may not cause interference, and (2) this device must accept

any interference, including interference that may cause undesired operation of the device.

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a

type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce

potential radio interference to other users, the antenna type and its gain should be so chosen that

the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful

communication.

The applicant is responsible for providing proper instructions to the user of the radio device, and any

usage restrictions, including limits of exposure durations. The user manual shall provide installation

and operation instructions, as well as any special usage conditions, to ensure compliance with SAR

and/or RF eld strength limits. For instance, compliance distance shall be clearly stated in the user

manual.

Radiation Exposure Statement:

Any Changes or modications not expressly approved by the party responsible for compliance could

void the user’s authority to operate the equipment.

For Remote controller, SAR tests are conducted using standard operating positions accepted by the

FCC/ISEDC with the device transmitting at its highest certied power level in all tested frequency

bands, although the SAR is determined at the highest certied power level, the actual SAR level of

the device while operating can be well below the maximum value.

Before a new model device is a available for sale to the public, it must be tested and certied to the

FCC that it does not exceed the exposure limit established by the FCC/ISEDC, Tests for each device

are performed in positions and locations (e.g. at the ear and worn on the body) as required by the

FCC/ISEDC.

For body worn operation, this model device has been tested and meets the FCC/ISEDC RF exposure

guidelines when used with an accessory designated for this product or when used with an accessory

that Contains no metal and that positions the handset a minimum of 10 mm from the body.

Non-compliance with the above restrictions may result in violation of RF exposure guidelines.

Produkspesifikasjoner

Merke:	Cobra
Kategori:	Radio
Modell:	ACXT360

Trenger du hjelp?

Hvis du trenger hjelp med Cobra ACXT360 still et spørsmål nedenfor, og andre brukere vil svare deg

Ditt navn*

Din e-post*

Skriv spørsmålet ditt her

Radio Cobra Manualer

Cobra ACXT360 Bruksanvisning

16 Oktober 2024

Radio Manualer

Nyeste Radio Manualer

Timex T331 Bruksanvisning

28 Oktober 2024

Scansonic R5 CD/FM Bruksanvisning

26 Oktober 2024

Tangent Alio Junior Bruksanvisning

24 Oktober 2024

Lexon Stelli Bruksanvisning

24 Oktober 2024

Schwaiger RAFM0100 Bruksanvisning

24 Oktober 2024

Audizio Milan Bruksanvisning

24 Oktober 2024

Midland BR180 Bruksanvisning

24 Oktober 2024

Sven SRP-50 Bruksanvisning

24 Oktober 2024

Roberts Rambler Max Bruksanvisning

24 Oktober 2024

Lexon Luma S Bruksanvisning

23 Oktober 2024