Elektrobock PT23 Bruksanvisning

Les nedenfor 📖 manual på norsk for Elektrobock PT23 (8 sider) i kategorien Termostat. Denne guiden var nyttig for 2 personer og ble vurdert med 4.5 stjerner i gjennomsnitt av 2 brukere

Side 1/8
PT23
for all types boilers with
ON / OFF
weekly program (preset)
6 temp. changes per every
day
anti-freeze mode
easy installation
modern design
LARGE WELL-ARRANGED DISPLAY
WITH TOUCHING CONTROL
ROOM THERMOSTAT
WITH BACKLIT DISPLAY
2
DESCRIPTION
PT23 is digital room thermostat with backlit display for automatic regulation of heating.
Its advantages involve a quick change in the desired temperature by simply press the button, and
possibility of setting up to weekly program with 6 temperature changes per day.
INSTALLATION
LOCATION
Install the thermostat at a suitable place where its operation cannot be affected by direct  ow of
hot air from the heater, sunshine or other disturbing effects. Do not install it on an external wall
either. The installation height should be approx. 1.5 m above the oor. Place the thermostat in
the “reference room”, such as the living room (the heating source will switch according to the
temperature in this room).
1. Switch off the main circuit breaker.
2. Remove the control part from the lower cover of the device (Fig.1).
3. Chip away the central plastic piece from the lower cover to lead in conductors.
4. Run the conductor through the hole and connect it to the terminal acc. to the diagram.
5. Fasten the lower cover to the wiring box with screws (Fig. 2).
6. Batteries are located at the back of the control part. Remove their protective paper (on  rst use), or insert new
batteries (Fig. 3).
7. Mount the control part on the lower cover.
8. Switch on the main circuit breaker and test correct connection of the thermostat, see page 5 (TEST).
9. Upon  rst start (or reset), the thermostat displays “SET CLOCK”, set the current time and date according to page 4.
Wiring diagram:
Backlit display
if any button is
pushed, the backlit
switches on
automatically for 5 s
at least
Control elements
by pressing
= con rmation of
value chagne
by pressing
= entering of main
menu or one step
back
by pressing
= changing the
set value
*The thermostat terminals
are marked differently with
every type of boiler.
Therefore, follow the
wiring prescribed
by the boiler
manufacturer!
*
BOILER
TEMP. IN AUTO
TEMP. IN MANU
3
Fig.1
HINTS FOR THE USER
Fig.2
Fig.3
alkal.battery
1,5 V / AA
alkal.battery
1,5 V / AA
QUICK CHANGE OF THE DESIRED TEMPERATURE
Press the button twice, the desired temperature starts blinking
on the display. With buttons change the required temperature
and press the „ “ button.
In the AUTO mode, the change lasts until the next program
change.
In the MANU mode, the change is permanent.
BATTERY REPLACEMENT
As soon as appears on the display, you must replace the
batteries.
1.Remove the control part from the lower cover of the device (Fig. 1).
2.Replace the batteries. Heed the correct polarity marked in the
battery compartment (Fig. 3). After removing the batteries, all
setting of the thermostat are saved in the memory
20 sec, only!
Always use the type AA, 2 x 1.5 V, alkaline batteries!
Recommendation: Check the batteries before every heating season!
Dispose of old batteries in conformity with regulations on hazardous
waste treatment!
The device can only be installed by a person with adequate qualication!
The installation must be executed in a voltage-free state!
+
+
-
-

Produkspesifikasjoner

Merke: Elektrobock
Kategori: Termostat
Modell: PT23

Trenger du hjelp?

Hvis du trenger hjelp med Elektrobock PT23 still et spørsmål nedenfor, og andre brukere vil svare deg




Termostat Elektrobock Manualer

Termostat Manualer

Nyeste Termostat Manualer