Evga XC3 Bruksanvisning

Les nedenfor 📖 manual på norsk for Evga XC3 (2 sider) i kategorien Ikke kategorisert. Denne guiden var nyttig for 2 personer og ble vurdert med 4.5 stjerner i gjennomsnitt av 2 brukere

Side 1/2
Installation Guide
All steps include removing the original shroud, heatsink, and screws, and then replacing those with the included new shroud, heatsink, waterblock, and provided
screws, with a few exceptions. The number of provided screws used will vary depending on whether the card uses a backplate. Several included accessories may
include extras. EVGA recommends a Phillips #1 screwdriver for all screws.
All suitable P/N for HYBRID installation are listed below. Please refer to the following table.
The following instructions and pictures are provided to assist your installation of the EVGA XC3 Hybrid Cooling Kit to the EVGA GeForce RTX™ 3090 and 3080
graphics cards. Please be careful installing the Kit; there are several very small fasteners used that can be stripped if you are not careful.
Please be sure to keep your original shroud, heatsink, and screws so your card can be returned to its original condition in
case you ever need to submit for warranty.
Included Accessories:
3. Remove the 3 screws on the I/O bracket and set them aside. You will reuse
them later.
Instructions:
1. Remove the 8 BP screws circled in red and carefully remove the backplate (if
present). Next, remove the 4 GPU screws circled in blue and remove the GPU
bracket.
For RTX 3090 XC3 ULTRA and XC3 cards: Removing the backplate may require
some force to loosen up the thermal pads. Make sure to place the thermal pads
on the backplate as shown in the image below, as you will reuse the backplate
and thermal pads.
2. Turn the card over and remove the heatsink from the card. Remove the fan
connectors (blue, beige, and black) first, and then the LED connector (black) as
you lift the heatsink o the card.
RTX™ 3090 XC3 ULTRA
RTX™ 3090 XC3
RTX™ 3090 XC3 BLACK
RTX™ 3080 XC3 ULTRA
RTX™ 3080 XC3
RTX™ 3090 XC3 BLACK
24G-P5-3975-KR
24G-P5-3973-KR
24G-P5-3971-KR
10G-P5-3885-KR
10G-P5-3883-KR
10G-P5-3881-KR
11 12
910
8
71 32 5
4 6
13
EVGA HYBRID Shroud with VRM Heatsinks/Fan Bracket
GPU & Memory Baseplate
EVGA HYBRID Pump and Radiator
M2.5 x 6.9mm spring screws (GPU). 7 pcs. PN: BAA125069001
M2 x 8.5mm Backplate screws (BP). 10 pcs. PN: BAA120085039
Mylar washers for spring screws. 5 pcs. PN: BGD100000003
1
2
3
4
5
6
Rubber plugs. 3 pcs. PN: BGB030007002
Tube Bracket. 1 pc. PN: BJD243038000
M2 x 7mm tube bracket screws. 2 pcs. PN: BAA120070024
Zip ties 4pcs and EVGA Cable ties 2pcs
8pcs screws and 8pcs washers to mount radiator
8
9
10
11
12
Thermal Grease 1 pack
13
M2 x 5mm screws (PCB). 15pcs. PN: BAA120050054
7
4. Using a lint-free cloth and high-percentage isopropyl alcohol, carefully clean
the GPU and remove any leftover thermal putty on the graphics card in the
regions marked below. Try to replace any loose thermal pads back onto the
original heatsink/cooler in case you need to restore the card to its original
condition.
Mounting the Radiator
Important Information
Important Information
5. Set the card aside for now, and remove the shroud, pump/waterblock, and
the tube bracket from the HYBRID kit. Place the pump in the notched locations
in the shroud, then secure the tubing with the tube bracket. Use one tube
bracket screw in the location marked below. Remove the plastic cover over the
pump/waterblock before proceeding to the next step.
6. Remove the GPU/Memory baseplate from the HYBRID kit and place it over
the 4 mounting holes over the pump/waterblock as seen in the image below. At
this time, remove any protective covering/tape over the thermal pads before
moving to the next step.
7. At this time, you will install the PCB onto the HYBRID cooler. First, you will need
to reconnect the fans and LED connector. Connect the LED connector first,
then connect the beige and black fan connectors to their respective headers.
The blue header will remain empty. Lastly, line up the screw holes and lower the
PCB onto the HYBRID cooler.
8b. Reinstall the I/O bracket and loosely fasten the 3 screws you removed earlier.8a. For all models, except for the 3080 XC3 BLACK, place a paper washer under
the 4 GPU screws, circled in blue, and fasten them loosely. Next, fasten the 5
PCB short screws, circled in red. Fully fasten the GPU screws at this time. Next,
complete Step 8b., then skip to Step 9.
8c. For the RTX 3080 XC3 BLACK, place a paper washer under the 4 GPU
screws, circled in blue, and fasten them loosely. Next, fasten 11 short PCB short
screws, circled in red. Fully fasten the GPU screws at this time. Lastly, fully
fasten the 3 screws on the I/O bracket to complete this installation.
9. For cards with a backplate, line up the screw holes and place the backplate on
the card. Fasten the 6 BP screws, circled in red. Next, fasten the 3 screws on the
I/O bracket. Lastly, install the rubber plugs into the holes designed for the
NVIDIA support bracket, circled in blue.
1. To mount the radiator, it is recommended that the radiator be installed at a level above the HYBRID graphics card. This will reduce pump noise and the potential to
create an air bubble in the loop.
2. The radiator will fit mounting holes designed for a 120mm x 120mm case fan, but the radiator will need a mounting area of 120mm x 240mm (approximately two
120mm case fans).
3. The default setting for the HYBRID’s radiator/fan is to blow through the radiator and outside the chassis. For that reason, we recommend installing the radiator at
the top of the chassis. If you plan to mount the radiator at the front of the chassis, you may wish to consider moving the fans to the opposite side of the radiator before
mounting.
4. Make sure that you leave some slack in the tubing lines to prevent damage to the tubing or internal fittings. If the tubes are twisted too much or pulled too tightly,
you may cause damage to the pump/radiator or cause the HYBRID kit to begin leaking.
5. When ready, line-up the radiator with the mounting holes on the chassis. On the outside of the chassis use #12 washers and screws to fasten the radiator to the
chassis.
EVGA XC3 HYBRID Kit is an AIO Water Cooling System. You do not need to add any coolant, and the system is completely self-contained. EVGA XC3 HYBRID Kits have
been leak-tested at the factory before shipping to customers.
EVGA XC3 HYBRID Kits are exclusive only to EVGA GeForce RTX 3090 and 3080 graphics cards and were not designed to fit on any other graphics cards.
Your EVGA XC3 HYBRID Kit comes with a 1 (one) year warranty. Refer to your EVGA GeForce RTX™ 3090 or 3080 graphics card manufacturers warranty information
before installing the EVGA XC3 HYBRID Kit. Should you damage your EVGA GeForce RTX 3090 or 3080 during the installation process, EVGA will not be held respon-
sible for any physical damage of your EVGA XC3 HYBRID Kit, case, motherboard or any associated hardware when damage is caused by improper installation.
E009-00-000307
Installation Guide

Produkspesifikasjoner

Merke: Evga
Kategori: Ikke kategorisert
Modell: XC3

Trenger du hjelp?

Hvis du trenger hjelp med Evga XC3 still et spørsmål nedenfor, og andre brukere vil svare deg




Ikke kategorisert Evga Manualer

Ikke kategorisert Manualer

Nyeste Ikke kategorisert Manualer