Holosun HS507C X2 Bruksanvisning

Holosun Ikke kategorisert HS507C X2

Les nedenfor 📖 manual på norsk for Holosun HS507C X2 (2 sider) i kategorien Ikke kategorisert. Denne guiden var nyttig for 6 personer og ble vurdert med 4.5 stjerner i gjennomsnitt av 2 brukere

Last ned PDF
Side 1/2
M
M
M
MMu
u
u
uul
l
l
llt
t
t
tti
i
i
ii-
-
-
--R
R
R
RRe
e
e
eet
t
t
tti
i
i
iic
c
c
ccl
l
l
lle S
e S
e S
e Se Sy
y
y
yys
s
s
sst
t
t
tte
e
e
eem
m
m
mm
Model
12
R
R
R
RRe
e
e
eef
f
f
ffl
l
l
lle
e
e
eex S
x S
x S
x Sx Si
i
i
iig
g
g
ggh
h
h
hht
t
t
tt
www.holosun.com
U
U
U
U
Us
s
s
s
se
e
e
e
er
r
r
r
r'
'
'
'
's M
s M
s M
s M
s Ma
a
a
a
an
n
n
n
nu
u
u
u
ua
a
a
a
al
l
l
l
l
HS 507C X2
R
R
R
RRe
e
e
eed C
d C
d C
d Cd Ci
i
i
iir
r
r
rrc
c
c
ccl
l
l
lle D
e D
e D
e De Do
o
o
oot
t
t
tt
HS507C X2 Reflex sightFig 1
Fig 4
Thank you for purchasing the HOLOSUN HS507C X2 Open
Reflex sight. This open reflex red dot sight is sized for use on
either a pistol or rifle. The stream lined design, Shake
Awake™ technology and our Solar Fail Safe™ dual power
system combine to make it the ideal sight for small arms.
Before operation, please read the User's Manual carefully.
3S
3S
default
Fig 3
1. Operates with our Solar Fail Safe™ dual power system
(solar cell and internal battery). One high quality CR1632
Lithium battery is included with purchase.
Caution: Do not use a rechargeable battery.
2. A high quality battery can power this device for up to
10000 hours (dot+circle) or 50000 hours (dot)at setting 6.
Important Notices
1. Ensure the firearm is unloaded and safe by removing all
ammunition and magazines from firearm and verifying an
empty chamber before installation and battery replacement.
2. Please keep the packaging should you need to make a
warranty claim.
Features
1) Three Operational Modes:Auto,Manual,Lockout.
2) Three Reticle Options: 32MOA circle and dot,2MOA dot
only and 32MOA circle only.
TM
3) Shake Awake - Motion on with last setting recall.
4) Parallax free, unlimited eye relief.
5) Drain holes on both sides of the optic allow for excess
water to drain in wet conditions.
6) CNC milled 7075 Aluminum Housing.
7) 10 day light and 2 night vision compatible brightness
settings.
8) Window Size 0.63x0.91 inches.
9) IP67 Certified.
The default reticle for this
sight is a 2MOA dot centered
in a 32MOA circle with four
positioning points.
Battery
NOTE: HS507C is compatible with some standard mounting
interfaces currently available. For a footprint drawing,
contact Holosun.
1.Place the HS507C on a compatible slide cut or adapter
plate.
2. Use either the included screws or screws supplied with
your slide or from your gunsmith and tighten to 15 INCH/lbs
using a non-permanent (medium/blue) thread locker. (Fig5)
3. Verify proper clearances and firearm function prior to use.
Installation on a Slide
Objective Lens
A canted objective lens is part
of the design of
reflex/reflective optical sights.
In order to create a proper
reflection of the reticle/dot Fig2
the objective lens must be perpendicular to the LED. Because
the LED is mounted to the side of the internal tube the
objective lens will be canted in that direction.
The diameter of the circle reticle represents approximately
32" at 100 yards (81cm at 100 meters).Hold the "-" button
down 3 seconds to switch between the three reticles (Circle
+Dot, Dot, or Circle) in that order. Fig 5
Caution:
The loss or damage of the seal ring may cause water to leak
into the compartment which could damage the product.
3.Battery Replacement(Fig4):
a. Remove the battery :
I. Remove the battery tray
screw.
ii. Use the included tool as a
lever in the battery tray slots
to remove the battery tray
and battery.
b. Battery installation :
I. Insert the battery into the battery tray with the POSITIVE
side facing DOWN.
ii. Insert and press the tray into the battery compartment.
iii. Tighten the battery tray screw.
Silicon
Solar Cell
Drain
Hole
Screw2
Screw1
Screw
Battery Tray
Seal Ring
Battery
Slot
Battery
Compartment
34
Fig 6
Three operation modes are available: Auto mode,manual
mode and lockout mode.See Fig 6.
1.Power ON: Press and release either brightness button
("+"or"-") to turn on the sight.
2.Power OFF: Press the"+"and"-" buttons simultaneously to
turn the power and motion sensor off.
Press and Hold the "-" button for 3 second to switch reticle
between circle +dot, dot, or circle.
3.Operation Mode: Three modes are available in the
following order: Auto Mode -> Manual Mode -> Lockout Mode.
1) Auto mode - operates with a solar cell and internal battery
two-way power supply: Based upon the ambient lighting level,
the sight will switch between battery and solar cell power
automatically. Accommodates operation in all lighting
conditions. Auto mode is the default setting.
a) In auto mode, the brightness of the reticle is automatically
adjusted to match ambient lighting.
b) The battery will compensate for power if the solar cell
cannot drive the reticle alone.
c) If lighting is low enough, the sight will automatically switch
to battery power. While running on battery power, you can
adjust the reticle brightness using the "+"and "-" buttons to
switch between higher and lower brightness levels.
2) Manual mode:
a) Switch to Manual mode from Auto mode by holding the “+”
button for about 3 seconds, until the reticle blinks once.
b) Brightness adjustment: There are 12 reticle brightness
setting levels in manual mode. Settings 1 and 2 are NV
compatible and setting 12 is the brightest. Press ”+” or ”-” to
increase or decrease the brightness.
3) Lockout Mode:
Switch to Lockout mode from Manual mode by holding the “+”
button for about 3 seconds, until the LED blinks once. In
lockout mode, momentary presses of the “+” or "-" button will
not change settings. To exit the lockout mode, press and hold
the + button again for 3 seconds, the LED will blink once then
switch to Auto Mode.
4. Sleep time setting:
1) Please note that your red dot will automatically enter into
sleep mode after 10 minutes of no movement.
2) The sight will instantaneously wake up and turn on with any
motion detected to last saved settings.
3) The default sleep timer setting is 10 min, but there 4
settings to select from.
i. Press and hold the “+” button for 10 seconds to enter sleep
time adjustment mode. There are 4 options: 10 min, 1h, 12h or
the sleep mode is disabled.
ii. Press and release the “+” or “-” button to select a sleep
timer setting. The LED will blink to show which setting is
selected: 1=10 min, 2=1h, 3=12h, or 4=sleep mode disabled.
iii. Press the “+” and “-” buttons simultaneously to save the
sleep timer setting (this will power off the sight).
5. Special operation:
1) Solar cell power: If the battery voltage is below 2.2Vdc,
please replace it. The sight will still operate if there is
sufficient ambient light for the solar cell.
2) To reduce power consumption when you have low battery
and/or low ambient light, you can toggle the 32MOA circle OFF
by holding the “-” button for about 3 seconds.
6. Note:
1) Memory function: The sight will remember the last saved
Caution: If you feel the knobs
can no longer be rotated, you
may have reached the
mechanical limit of the
adjustment turret. Do not try
to rotate the knobs further if
you feel a bind or you may
cause damage.
Fig 7
Sight Operation Zero Setting
1) This sight has been factory adjusted to an approximate 25
yard zero and should require minimal adjustment to achieve
zero.
2) The Elevation adjustment is located on top of the tail
section of the housing and the Windage adjustment is
located on the right side of the housing. Adjustment can be
performed by inserting the flat-tipped end of the included
tool into the turret slot and rotating, See Fig 7.
3) Windage and Elevation adjustments are approximately 1
MOA per click.
4) Each adjustment click has a value of approximately 1 MOA
or 1 inch at 100 yards (1/2" at 50y; 1/4" at 25y). When
zeroing at 25 yard, if your impacts are 2 inches low and 1 inch
right, you will need to adjust Elevation 8 clicks UP
(counterclockwise) and 4 clicks LEFT (clockwise)
5) The maximum adjustment range is 50MOA from center. ±
HS507C X2
Reflex Sight
Holosun Technologies Inc.
www.holosun.com
C
C
C
CCu
u
u
uus
s
s
sst
t
t
tto
o
o
oom
m
m
mme
e
e
eer S
r S
r S
r Sr Se
e
e
eer
r
r
rrv
v
v
vvi
i
i
iic
c
c
cce
e
e
ee
We provide a limited lifetime warranty from the date of
purchase on parts and workmanship to the original
purchaser. At our sole discretion, we will repair or replace
products found to be defective under normal use without
charge, excluding any delivery costs, which will be born by
purchaser. We will not be liable for incidental, consequential,
or special damages arising out of or in any connection with
the use or performance of this product. This warranty is void
if the product has been misused, modified, neglected, or
disassembled prior to its return. Please refer to
www.holosun.com for current and complete warranty
information and other conditions.
This device is a precision instrument that deserves
reasonably cautious care. The following tips are provided to
ensure a long product life. The optical lenses are multicoated
optical glass. When cleaning the lenses, blow away any dust
on the surface, wet the lens with lens cleaner or clean water,
then wipe away smudges with lens tissue, soft cotton or a
microfiber cloth. Avoid touching the glass surface with dry
cloth or tissue paper. Do not use organic solvents such as
alcohol or acetone. No special maintenance is needed for the
housing surface. Do not try to dismantle the device as the
internal parts are specially cleaned and sealed and with an
anti-fog treatment. Any such attempt will void the warranty.
Limited Warranty
Maintenance & Care
Phone: (909) 594-2888
Fax: (909) 598-4888
E-mail: warranty@holosun.com
Tools: wrench
1. Flat tab is used to adjust the
Windage & Elevation.
2. T10 Torx wrench for screws. Fig 8
Ver A0
brightness setting when
powered on and off.
2) Low battery Warning: If
the battery voltage is
below 2.2Vdc, the reticle
will blink slowly.
Brightness
Increase
Brightness
Decrease
Windage
Adjustment Screw
Elevation
Adjustment
Screw
②①

Produkspesifikasjoner

Merke: Holosun
Kategori: Ikke kategorisert
Modell: HS507C X2

Trenger du hjelp?

Hvis du trenger hjelp med Holosun HS507C X2 still et spørsmål nedenfor, og andre brukere vil svare deg


Ikke kategorisert Holosun Manualer

Holosun

Holosun DRS-NV Bruksanvisning

16 Oktober 2024
Holosun

Holosun HS507C X2 Bruksanvisning

16 Oktober 2024
Holosun

Holosun AEMS-CORE-120101 Bruksanvisning

16 Oktober 2024

Ikke kategorisert Manualer

Nyeste Ikke kategorisert Manualer

Daewoo

Daewoo Cyclone Essential FLR00038 Bruksanvisning

28 Oktober 2024
IFM

IFM SU6631 Bruksanvisning

28 Oktober 2024
IFM

IFM SU7031 Bruksanvisning

28 Oktober 2024
IFM

IFM SV8051 Bruksanvisning

28 Oktober 2024
Daewoo

Daewoo AVS1464 Bruksanvisning

28 Oktober 2024
IFM

IFM PT5300 Bruksanvisning

28 Oktober 2024
IFM

IFM KTE301 Bruksanvisning

28 Oktober 2024
IFM

IFM OVP810 Bruksanvisning

28 Oktober 2024
IFM

IFM SF0516 Bruksanvisning

28 Oktober 2024
IFM

IFM TSM701 Bruksanvisning

28 Oktober 2024