Kohler Components K-T78025-8-BL Bruksanvisning
Kohler
Kontroller
Components K-T78025-8-BL
Les nedenfor 📖 manual på norsk for Kohler Components K-T78025-8-BL (20 sider) i kategorien Kontroller. Denne guiden var nyttig for 2 personer og ble vurdert med 4.5 stjerner i gjennomsnitt av 2 brukere
Side 1/20
Installation Guide
Stainless Steel Kitchen Sinks
Mproduct numbers are for Mexico (i.e. K-12345 )M
Los números de productos seguidos de
Mcorresponden a México (Ej.
K-12345 )M
Français, page “Français-1”
Español, página Español-1”″
K-3145 K-3361
K-3362 K-3363
K-3369
1013270-2-E
Thank You For Choosing Kohler Company
We appreciate your commitment to Kohler quality. Please take a few
minutes to review this manual before you start installation. If you
encounter any installation or performance problems, please don’t
hesitate to contact us. Our phone numbers and website are listed on
the back cover. Thanks again for choosing Kohler Company.
Tools and Materials
Before You Begin
WARNING: Risk of personal injury. Metal surfaces are sharp
and can cause severe cuts. Use gloves and handle sink edges
carefully.
Observe all local plumbing and building codes.
Shut off the hot and cold water supplies.
Prior to installation, unpack the new sink and inspect it for
damage. Return the sink to its protective carton until you are
ready to install it.
Inspect the drain and supply tubing. Replace if necessary.
All information in these instructions is based on the latest product
information available at the time of publication. Kohler Co.
reserves the right to make changes at any time without notice.
• Keyhole/Jigsaw
• Gloves
• 5/16" Deepwall Socket or
5/16" Nut Driver
• Level
Plus:
Drill Putty KnifeMeasuring
Tape
Safety
Glasses
Pencil
Silicone
Sealant
Plumbers
PuttyPipe Wrench
1013270-2-E 2 Kohler Co.
1. Preparation
WARNING: Risk of personal injury. Metal surfaces are sharp
and can cause severe cuts. Use gloves and handle sink edges
carefully.
For new installations:
Carefully place the sink upside down on the countertop in the
desired position. Be careful not to damage the sink finish.
Make sure the sink will not interfere with the cabinet.
Trace the sink outline onto the countertop. Do cut along thenot
outline.
For existing installations:
Carefully lift the old sink out of the countertop.
Compare the existing cut-out to the required cut-out size.
If needed, enlarge the cut-out hole according to the directions for
new installations.
For all installations:
Draw a line 1/4 (6 mm) inside the sink outline.″
Before cutting, measure the cut-out line you just drew and
compare it to the overall sink dimensions. The cut-out should be
1/2 (1.3 cm) smaller than the overall sink dimensions.″
Sink
Countertop
Trace the outline of the sink on
the countertop with a pencil at the
desired installation location.
Sink Outline
Create a second line 1/4" (6 mm)
in from the original sink outline.
Pilot
Hole
1/4"
(6 mm)
Kohler Co. 3 1013270-2-E
Produkspesifikasjoner
| Merke: | Kohler |
| Kategori: | Kontroller |
| Modell: | Components K-T78025-8-BL |
Trenger du hjelp?
Hvis du trenger hjelp med Kohler Components K-T78025-8-BL still et spørsmål nedenfor, og andre brukere vil svare deg
Kontroller Kohler Manualer
31 Januar 2025
31 Januar 2025
31 Januar 2025
31 Januar 2025
31 Januar 2025
31 Januar 2025
31 Januar 2025
31 Januar 2025
31 Januar 2025
31 Januar 2025
Kontroller Manualer
- Kontroller IFM
- Kontroller Balam Rush
- Kontroller StarTech.com
- Kontroller Trust
- Kontroller Axis
- Kontroller Somfy
- Kontroller Bose
- Kontroller DataVideo
- Kontroller BeamZ
- Kontroller Smart-AVI
- Kontroller Canon
- Kontroller Sonance
- Kontroller Mitsubishi
- Kontroller Showtec
- Kontroller Hikvision
- Kontroller Genesis
- Kontroller Chauvet
- Kontroller Speed-Link
- Kontroller PCE Instruments
- Kontroller Vizio
- Kontroller MOZA
- Kontroller Rosco
- Kontroller American DJ
- Kontroller Thrustmaster
- Kontroller Ltech
- Kontroller Korg
- Kontroller PDP
- Kontroller Gamesir
- Kontroller 8BitDo
- Kontroller Kanlux
- Kontroller Savio
- Kontroller Logitech
- Kontroller PTZ Optics
- Kontroller Alfatron
- Kontroller Indiana Line
- Kontroller Steelseries
- Kontroller Magnus
- Kontroller Nacon
- Kontroller GVM
- Kontroller AirTurn
- Kontroller HQ Power
- Kontroller Hotone
- Kontroller IVT
- Kontroller Metronic
- Kontroller COLBOR
- Kontroller Gioteck
- Kontroller Audibax
- Kontroller HuddleCamHD
- Kontroller Dangerous Music
- Kontroller Datapath
- Kontroller IPEGA
- Kontroller PowerA
- Kontroller Nyko
- Kontroller Turtle Beach
- Kontroller Visual Productions
Nyeste Kontroller Manualer
3 April 2025
31 Mars 2025
31 Mars 2025
30 Mars 2025
30 Mars 2025
30 Mars 2025
29 Mars 2025
27 Mars 2025
27 Mars 2025
26 Februar 2025