Movo WMX-1 Bruksanvisning

Movo Mikrofon WMX-1

Les nedenfor 📖 manual på norsk for Movo WMX-1 (1 sider) i kategorien Mikrofon. Denne guiden var nyttig for 3 personer og ble vurdert med 4.5 stjerner i gjennomsnitt av 2 brukere

Last ned PDF

Side 1/1

Thank you for purchasing MOVO WMX-1!

Please don’t touch here during using, otherwise, it

will effect signal.

Please don’t touch here during using, otherwise, it

will effect signal.

7. Battery compartment

Accommodates two pieces of AAA batteries.

For more details, please see “Installing batteries”

on page 9.

For more details, please see “Installing or

uninstalling clip” on page 13.

8. Clip

1. Earphone Jack

Instruction Manual

(3.5mm diameter stereo mini jack)

To monitor the receiver output, connect the

headphones to this connector.

NOTE：

Do not connect headphones with a monaural mini jack.

This may lead to short-circuiting of the headphone

output, resulting in distorted sound output.

2. LINE OUT (audio output) Jack

- For cameras, camcorders, audio recorders and

other audio/Video recording devices.

Connect one end of the supplied TRS stereo 3.5mm

mini output cable here, and the other end to camera.

3. Power LED

For more details, please see “Power LED” on page 5.

4. Power OFF/ON

Press these buttons to set the attenuation level of

the input signal.

6. Antenna

7. Battery compartment

Accommodates two pieces of AAA batteries.

For more details, please see “Installing batteries”

on page 9.

8. Clip

For more details, please see “Installing or

uninstalling clip” on page 13.

9.Shoe mount adapter

①②

③

④

⑧

⑤

⑥⑦

②

①

③

④

⑤

⑥

⑦

⑧

What’s difference?

MICROPHONE SMARTPHONE

How to use it

Insert batteries in the transmitter and

receiver units

1. Both transmitter and receiver requires two AAA size

batteries.

2. Slide and remove the transmitter’s battery

compartment cover.

3. Insert two pieces of batteries.

4. Close the battery compartment cover.

5. Do the same ways as step 2 to 4 to insert battery

into receiver.

Connecting the transmitter and receiver

Using the microphone with smartphone, tablet,

Mac or laptop with combo headphone/Mic jack.

Receiver

Using the microphone with cameras, camcorders,

audio recorders and other audio/video recording

devices.

Connecting the Transmitters and the Receiver

Receiver

Receiver (RX)

3.5 mm TRS connector

- For cameras, camcorders, audio recorders and

other audio/video recording devices.

3.5 mm TRRS connector

- For Smartphone, tablet, Mac or laptop with

combo headphone/Mic jack

Connect to

Receiver “LINE OUT” Connect to Smartphone

1 2 3 4 5 6 7 8 9

10 11 12 13 14 15 16 17 18

- For using smartphone, tablet or Mac

Connect one end (90° plug) of the supplied

TRRS stereo 3.5mm mini output cable here, and

the other end (straight plug) to smartphone.

5. Volume +/-

Designed for videographers on a limited budget

and video hobbyists, WMX-1 is a new generation

2.4 GHz wireless microphone, dual-Channel

for capturing audio with dual subjects to your

smartphones, tablets, DSLR cameras, consumer

camcorders, PCs etc.

WMX-1 K1 consists of one body-pack

transmitter(TX), a portable receiver

(RX), and their accessories as following:

Transmitter(TX) Receiver(RX)

Lavalier/lapel microphone 3.5mm to TRS audio output cable

3.5mm to TRRS audio output cable

1. Microphone input

- Connect the supplied lavalier microphone here.

- Fully insert the microphone’s 3.5mm plug and

make sure it clicks into place.

2. Line In

3. Power LED

1) The power LED flash blue when the unit is on.

2) The power LED glows red when low power.

For more details about LED indicator, please refer to

as following:

Status Receiver Transmitter

Stays blue

Flashes continually

every 1 second.

Flashes in blue

Flashes in redLow power

Off

Flashes in blueOff

Flashes continually

every 2.5 seconds.

The transmitter and the receiver connects.

The transmitter and the receiver disconnects.

Receiver unit is turned OFF(Transmitter is still ON)

Transmitter unit is turned OFF(Receiver is still ON)

Flashes continually

every 1 second.

4. Power OFF/ON

5. Pair

This botton is for connecting signal.

For details, please see “How to connect transmitter

and receiver” on page 11.

6. Antenna

Transmitter (TX)

Feature：

• Dual-Channel Wireless Receiver

• Digital 2.4 GHz Frequency Band

• Super-clear recording sound

• Compatible with smartphones, DSLR cameras,

consumer camcorders, PCs etc.

• Lightweight and compact for easy carrying

• Omnidirectional lavalier microphone

• Hard case included

• Standard camera shoe mount and clip included

• Up to 60m (197ft) operation range (without obstacle)

• Power supplied by two AAA batteries for transmitter

and receiver.

Specifications:

RF Modulation:

Frequency band:

Frequency response:

Signal/Noise:

Distortion:

RF output level:

Earphone output level:

Reception sensitivity:

Audio input connector:

Operation range:

Power requirements:

Consumption power:

Dimensions:

Weight:

GFSK (Gauss frequency Shift Keying)

2.4GHz (2405-2478MHz)

35Hz-14KHz±3dB

84dB or more

0.05% or less (32Ω,1 KHz,65mW output)

3mW

32Ω,65mW

-90dB +/- 3dB / 0dB=1V/Pa, 1kHz

3.5mm mini jack

60m (197ft) (without obstacle)

3V DC (Two AAA size batteries)

Transmitter: 3V/70mA

Receiver：3V/70mA

Receiver: 45x70x35mm (1.8*2.8*1.4 inches)

Transmitter: 45x70x35mm (1.8*2.8*1.4 inches)

Receiver: 47g (1.7 oz)

Transmitter: 47g (1.7 oz)

CAUTION

1.Please use our original audio signal cable which is

equipped, it’s more compatible with the wireless

microphone, and make the sound better.

2.The figure given is only the approximate value that

applies when there are no obstructions between the

transmitter and receiver. This distance will vary

depending on metal objects, people and other

obstructions and on the signal strength.

3.Battery life may vary depending on the type of

battery used.

IMPORTANT

• If you do not intend to use the wireless microphone

for a long period time, please remove the batteries

from both the transmitter and receiver.

• Do not touch the lavalier/lapel microphone,

transmitter and receiver while recording, as this will

cause noise to be recorded.

• Do not let the transmitter close to high-voltage

equipment or to devices that emit strong electrom-

agnetic fields, otherwise, it may cause the noise to

be recorded.

• Do not use or leave the transmitter and receiver in

hot, humid places.

• Do not leave the receiver attached to the camera

when storing the camera in a case.

• Do not mix up to use the transmitter and receiver.

MAINTENANCE

• Do not operate the device with wet hands or feet.

• Clean the equipment only in the way described in

the instructions for use.

• Take care to prevent the equipment from dropping

down.Make sure that the device is properly fastened

and reliably mounted. If the device has dropped down

on the floor have it inspected by a skilled electrician

before you switch it on again.

• Should the equipment be damaged or defective,or if

you notice a scorching smell:

Interrupt the electric power supply immediately by

removing the batteries.Do not operate the device

with a damaged housing,do not repair the device

yourself. Have the device only repaired by a skilled

electrician.

• Always keep your device in good condition,as

specified in these in-structions for use.

• Do not open the device.

WARNING

• Keep the wireless microphone out of the reach of

children.

• Never use leaking batteries and never expose

batteries to excessive heat or fire.

WARNING

FCC STATEMENT :

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received,

including interference that may cause undesired operation.

Warning:

Changes or modifications not expressly approved by the

party responsible for compliance could void the user's

authority to operate the equipment.

NOTE:

This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interfer-

ence in a residential installation.

This equipment generates uses and can radiate radio

frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications. However, there is

no guarantee that interference will not occur in a partic-

ular installation. If this equipment does cause harmful

interference to radio or television reception, which can

be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by

one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

RF warning statement:

The device has been evaluated to meet general RF

exposure requirement. The device can be used in

portable exposure condition without restriction

1. Mount receiver to Smartphone, tablet, Mac or laptop.

2. Using TRRS cable, plug the 3.5 mm connector(straight

plug) into the audio jack of your smartphone.

3. Insert the 90° plug of the connecting cable into

the receiver “LINE OUT” jack.

4. Insert earphone into receiver “ ” for monitoring

Sound if you need.

5. Slider the power ON/OFF switch to ON position ( the

LED indicator will light in blue)

Caution: Please do not mix up plug, for details, please

refer to” What’s difference” on page 8.

1. Mount receiver to cameras, camcorders, audio

recorders and other audio/video recording devices.

2. Using TRS cable, plug the 3.5 mm connector into the

audio jack of your camera.

3. Insert the other end of the connecting cable into

the receiver “LINE OUT” jack.

4. Insert earphone into receiver “ ” for monitoring

Sound if you need.

5. Slider the power ON/OFF switch to ON position ( the

LED indicator will light in blue)

Caution: Please do not mix up audio cable, for details,

please refer to” What’s difference on page 8”.

Install microphone

1. Clip is mounted on the microphone before leaving

factory.

2. Both transmitter and receiver include clip, that means

you can mount them in any place you want.

3. Adjust the direction of the microphone to your mouth

by rotating the Microphone.

If transmitters and receiver disconnect, please follow

below steps:

Otherwise, the light for receiver and transmitters will

flash continually every 1 second, then try 1-4 steps

again.

Before leaving factory, the connection of transmitters

and receiver will be established.

1. Turn on the receiver and the transmitters.

2. Press the button “+” and “-“ for 3 seconds for

receiver and press "Pair" of one transmitter for 3

seconds at the same time.

3. When transmitter and receiver connects, the light

of receiver will stay blue, the light of transmitters

will flash every 2.5 seconds.

4. Repeat step 2 for the other transmitter.

If receiver need to be mounted onto camera hot/cold

shoe, please follow below steps:

1. Push the clip to right side.

2. Push the cold shoe mount on the position.

3. Mounted receiver onto camera hot/cold shoe

WMX-1

Dual-Channel Digital Wireless Microphone

⑨

NOTE:

Not all Android devices support external microphone

when taking video, and you may need to download a

third-party app and set up sound source as external

microphone.

WMX-1 K2 consists of two body-pack

transmitters(TX), a portable receiver

(RX), and their accessories as following:

Transmitter(TX) p1-x2 Receiver(RX)

Lavalier/lapel microphone p1-x2 3.5mm to TRS audio output cable

3.5mm to TRRS audio output cable

Microphone Holder clipWind screen

Shoe mount adapter

Microphone Holder clip (x2)Wind screen (x2)

Shoe mount adapter

NOT HAPPY? LET US HELP!

Have y o o o e ? an questi ns r c nc rns

Ca u at ll s 1-8 5 7 S)00-3 4-1 39 (U

Ou i d r n v er serv e r fr endly an espo si e custom ic

wa to mak r ou t t r ce nts e su e y have he bes expe ien

poss blei !

Mon ay-Friday:d 9 am m - 4 p (PST)

E at mail us su @m o compport ovoph to.

Li chat u t ve s a www.m o t comov pho o.

HAPPY? LET US KNOW!

We ve o hea o ome !lo t r fr m cust rs

Sha ou ex en o r r i ing re y r peri ce with the s by ev ew

your on on. can he QR product Amaz S t c ode below

o : r visit

a n o r r i :mazo .c m/ eview/ ev ew-your-purchases#

Act Now!

Th pr inclu 1 it ed t is oduct des a year lim warran y.

If y he p ys ofou register t roduct within 30 da

purc se, yo ’ll eive n ddit nalha u rec a a io 1-year

w rantyar e ax i ftens on or tota o of l of tw years

protection.

To r i r r t d r u detai o t eg ste your p oduc an fo f ll ls n he

w rant isit ar y, v www.m ophot /wa antyov o.com rr or

scan c QR ode:

F & tu ovo oto pacebook You be: /m ph grou

T tter & s ovo otowi In tagram: @m ph

Movo Photo Group

www.movophoto.com

support@movophoto.com

Produkspesifikasjoner

Merke:	Movo
Kategori:	Mikrofon
Modell:	WMX-1

Trenger du hjelp?

Hvis du trenger hjelp med Movo WMX-1 still et spørsmål nedenfor, og andre brukere vil svare deg

Ditt navn*

Din e-post*

Skriv spørsmålet ditt her

Mikrofon Movo Manualer

Movo VXR10 PRO Bruksanvisning

19 Oktober 2024

Movo VXR10 Bruksanvisning

19 Oktober 2024

Movo WMX-1 Bruksanvisning

19 Oktober 2024

Mikrofon Manualer

Nyeste Mikrofon Manualer

Karma DM 790 Bruksanvisning

28 Oktober 2024

Akg HT470 C5 Bruksanvisning

27 Oktober 2024

Akg HT470 D5 Bruksanvisning

27 Oktober 2024

Akg PT470 Bruksanvisning

27 Oktober 2024

Akg HT420 Bruksanvisning

27 Oktober 2024

Point Source Audio CO-3-Kit Bruksanvisning

27 Oktober 2024

Point Source Audio CO-8WD Bruksanvisning

27 Oktober 2024

Shure SBC-DC-903 Bruksanvisning

27 Oktober 2024

Point Source Audio GO2-9WD Bruksanvisning

27 Oktober 2024

Roland CS-15 Bruksanvisning

26 Oktober 2024