Audio-Technica PRO35 Bruksanvisning

Les nedenfor 📖 manual på norsk for Audio-Technica PRO35 (2 sider) i kategorien Mikrofon. Denne guiden var nyttig for 3 personer og ble vurdert med 4.5 stjerner i gjennomsnitt av 2 brukere

Side 1/2
SCALE IS 5 DECIBELS PER DIVISION
Polar Pattern
200 Hz
LEGEND
5 kHz
1 kHz
8 kHz
12" or more on axis
LEGEND
Roll-off
Frequency in Hertz
Frequency Response
Response in dB
Ideal for sax, toms, brass and percussion
Excels in high-SPL applications
Perfect for active stage performances
Extended frequency response captures subtle nuances of the
performance
• UniMount®clip permits accurate positioning, provides shock
resistance and protects element
Corrosion-resistant contacts from gold-plated XLRM-type
connector
Cardioid polar pattern reduces pickup of sounds from the sides
and rear, improving isolation of desired sound source
The PRO 35 is intended for use in professional applications where
remo te pow er is availabl e. It r eq uires 11 V to 52V DC
phantom power, which may be provided by a mixer or console, or
by a separate, in-line source such as the Audio-Technica AT8801
single-channel or CP8506 four-channel phantom power supplies.
An integ ral 80 Hz high-pass filter provides easy switching from a flat
frequency response to a low-end roll-off. The roll-off position
reduces the pickup of low-frequency ambient noise (such as traffic,
air-handling systems, etc.), room reverberation and mechanically
coupled vibrations.
Output from the power module’s XLRM-type connector is low
impedance (Lo-Z) balanced. The signal appears across Pins 2 and
3; Pin 1 is ground (shield). Output phase is “Pin 2 hot” positive
acoustic pressure produces positive voltage at Pin 2.
To avoid phase cancellation and poor sound, all mic cables must be
wired consistently: Pin 1-to-Pin 1, etc.
Av oid leaving the microphone in the open sun or in areas where
temperatures exceed 110° F (43° C) for extended per iods.
Extremely high humidity should also be avoided.
PRO 35 SPECIFICATIONS
ELEMENT Fixed-charge back plate
permanently polarized condenser
POLAR PATTERN Cardioid
FREQUENCY RESPONSE 50-15,000 Hz
LOW FREQUENCY ROLL-OFF 80 Hz, 18 dB/octave
OPEN CIRCUIT SENSITIVITY 45 dB (5.6 mV) re 1V at 1 Pa*
IMPEDANCE 250 ohms
MAXIMUM INPUT SOUND LEVEL 145 dB SPL, 1 kHz at 1% THD
DYNAMIC RANGE (typical) 115 dB, 1 kHz at Max SPL
SIGNAL-TO-NOISE RATIO
164 dB,1 kHz at 1 Pa*
PHANTOM POWER REQUIREMENTS 11-52V DC, 2 mA typical
SWITCH Flat, roll-off
WEIGHT (less cable and accessories)
MICROPHONE 0.3 oz (8 g)
POWER MODULE 2.9 oz (81 g)
DIMENSIONS
MICROPHONE 0.98" (25.0 mm) long,
0.40" (10.2 mm) diameter
POWER MODULE 3.66" (92.9 mm) long,
0.74" (18.9 mm) diameter
OUTPUT CONNECTOR Integral 3-pin XLRM-type
(power module)
CABLE 6.0' (1.8 m) long (permanently
attached to microphone),
0.10" (2.6 mm) diameter,
2-conductor, shielded cable with
TA3F-type connector
ACCESSORIES FURNISHED AT8418 UniMount®microphone
instrument mount; AT8538 power
module; soft protective pouch
In the interest of standards development, A.T.U.S. offers full details on its test
methods to other industry professionals on request.
*1 Pascal = 10 dynes /cm2= 10 microbars = 94 dB SPL
1Typical, A-weighted, using Audio Precision System One.
Specifications are subject to change without notice.
Audio-Technica U.S., Inc., 1221 Commerce Drive, Stow, Ohio 44224
Audio-Technica Limited, Old Lane, Leeds LS11 8AG England
www.audio-technica.com
P51764 ©2005 Audio-Technica U.S., Inc. Printed in Japan
PRO 35 CARDIOID CONDENSER CLIP-ON
INSTRUMENT MICROPHONE

Produkspesifikasjoner

Merke: Audio-Technica
Kategori: Mikrofon
Modell: PRO35

Trenger du hjelp?

Hvis du trenger hjelp med Audio-Technica PRO35 still et spørsmål nedenfor, og andre brukere vil svare deg




Mikrofon Audio-Technica Manualer

Mikrofon Manualer

Nyeste Mikrofon Manualer