Emko ESM-3722 Bruksanvisning
Les nedenfor 📖 manual på norsk for Emko ESM-3722 (2 sider) i kategorien Termostat. Denne guiden var nyttig for 4 personer og ble vurdert med 4.5 stjerner i gjennomsnitt av 2 brukere
Side 1/2
2.2PanelCut-Out
ESM- 77x35DINSizeHatcherController3722
InstructionManual.ENGESM-372201V0402/15
2.GeneralDescription
2.1FrontViewandDimensionsofESM-3722HatcherController
All order information of ESM-3722 Hatcher Controller are given on the table at above. User may form
appropriate device configuration from information and codes that at the table and convert it to the
ordering codes.Firstly, supply voltage then other specifications must be determined. Please fill the order
code blanks according to your needs. Please contact us, if your needs are out of the standards.
10.OtherInformations
WhenSET buttonispressedfor3
seconds,“P”ledturn.Ifprogramming
modeenteringpasswordisdifferent
from0,programmingmodeentering
screenwillbeobserved.
MainOperationScreen
ProgrammingScreen
Changethevaluewithincrement
anddecrementbuttons.
Press SET button for accessing to the
parameter value. Press increment
button for accessing to the next
parameter, press decrement button for
accessing to the previous parameter.
Presssetbuttonforsavingthe
parameter.
Press increment button for accessing to
the next parameter, press decrement
button for accessing to the previous
parameter.
ProgrammingMode
EnteringScreen
PressSET buttonfor
accessingtothe
passwordentering
PasswordEnteringScreen
Enterprogrammingmodeaccessing
passwordwithincrementand
decrementbuttons.
Note2: If programming mode accessing password is 0, only three parameters are accessible, and the
parameter values can be changed.
PressSET/OKbuttonfor
enteringthepassword.
Note1: Ifprogramming
modeaccessingpassword
is0, TemperatureUnit
screen isobserved
insteadofprogramming
screen
If no operation is performed in programming mode for 20 seconds, device turns to main
operation screen automatically.
i
DecimalSeparatorEnabling
SelectionScreen
5.5EnteringToTheProgrammingMode,ChangingandSavingParameter
14
13
3sec.
76mm/3inch
34,5mm/1.36inch
15
While button protection parameter value is 0,1,2 or
4 in main operation screen if engine button is pressed,
manual engine start will be active.When the button is
released the engine start will be passive and engine stops.
6. ManualStartofEggTrayRotatorOperationwithEngineButton
Note-1: If input type is selected PTC or NTC (B = 2, 3), Temperature sensor is given with the
device.For this reason, if input type is selected as PTC,sensor type (V = 0,1 or 2) or if input type is
selected as NTC, sensor type (V = 0, 3 or 4) must be declared in ordering information.
8.Specifications
PasswordEnteringScreen
TemperatureUnitSelection
ParameterValue
TemperatureUnitSelection
ParameterValue
8.Specifications
c
1.2.GeneralSpecifications
1.Preface
ESM3722-HT seriesHatchercontrollersaredesignedforcontrollinghatcherprocess.Device
canbeusedeasilywithPIDorOn-Offcontrolformandmanualstartofeggtrayrotatorproperties.
ESM-3722
PowerSupply
Input
Output
Output
Output
2
Humidification
EggTrayRotatorOutput
Alarm
1.1EnvironmentalRatings
-4DigitsforTemperatureDisplay
-4DigitsforHumidityDisplay
-TemperatureSensorInput
NTC,PTC,PT-100,0/2..10V,0/4..20mA orProNemMiniPMI-P
(Mustbedeterminedinorder.)
-HumiditySensorInput
0/2..10V,0/4..20mA orProNemMiniPMI-P
(Mustbedeterminedinorder.)
-4Output
HeatingControlOutput
EggtrayrotatorOutput
HumidificationControlOutput
AlarmControlOutput
-RelayorSSROutputs(Mustbedeterminedinorder.)
-SelectableTemparatureControl(PIDorON/OFF)
- Auto-TunePID
-Setvalueboundaries
-ManualStartoftrayrotatorfromfrontpanel
- Alarmparametreters
- Adjustableinternalbuzzeraccordingtothealarmsituations
-Passwordprotectionforprogrammingmode,
ESM- 77x35DINSize3722
DigitalHatcherController
3 416
MountingClamp
PanelSurface
(maximumthickness15mm/0.59inch)
Frontpanel
IP65Protection
65mm/2.56inch
6mm/0.24inch
110mm/4.33inch(min)
71mm/2.79inch
29mm/1.14inch
50mm/1.97inch(min)
Maximum15mm/0.59inch
230V ( %15)50/60HzV±
OptionalSupply
Voltage
-30V Z
115V ( %15)50/60Hz
24V ( %15)50/60Hz
24V ( %15)50/60Hz
10
±
±
±
V
V
W
Standard
DeviceType
Housing&Mounting
ProtectionClas
Weight
EnviromentalRatings
Storage/OperatingTemperature
Storage/OperatingHumidity
Installation
OvervoltageCategory
PollutionDegree
OperatingConditions
SupplyVoltageandPower
TemperatureSensorInput
:HatcherController
:76mmx34.5mmx71mmPlastichousingforpanel
Panelcutoutis71x29mm.
:Ip65atfront,Ip20atrear.
: Approximately0.2Kg
:Standart,indooratanaltitudeoflessthan2000meterswith
nonecondensinghumidity.
:-40 Cto+80 C/-30 Cto+80 C
:90%max.(Nonecondensing)
:Fixedinstallation
:II.
:II,officeorworkplace,noneconductivepollution
:Continuous
:
:115
:24
:24
:10-30
:NTC,PTC,PT-100,0/2..10V 0/4..20mA or
ProNemMiniPMI-P
o o o o
Z Z,
230V ( %15)50/60Hz-1.5VA
V ( %15)50/60Hz-1.5VA
V ( %15)50/60Hz-1.5VA
V ( %15)50/60Hz-1.5VA
V 1.5WZ
V
V
V
W
±
±
±
±
Output Heating
YourTechnologyPartner
www.emkoelektronik.com.tr
Thankyouverymuchforyourpreferenceto
useEmkoElektronikproducts,pleasevisitour
webpagetodownloaddetailedusermanual.
OperatingTemperature:
Max.OperatingHumidity:
Altitude :
0to50°C
90%Rh(non-condensing)
Upto2000m.
Forbidden Conditions:
Corrosive atmosphere
Explosive atmosphere
Home applications (The unit is only for industrial applications)
A visual inspection of this product for possible damage occurred during shipment is recommended
before installation.
It is your responsibility to ensure that qualified mechanical and electrical technicians install this product.
If there is danger of serious accident resulting from a failure or defect in this unit, power off the system
and separate the electrical connection of the device from the system.
The unit is normally supplied without a power supply switch or a fuse. Use power switch and fuse as
required.
Be sure to use the rated power supply voltage to protect the unit against damage and to prevent failure
Keep the power off until all of the wiring is completed so that electric shock and trouble with the unit can
be prevented.
Never attempt to disassemble, modify or repair this unit. Tampering with the unit may results in
malfunction, electric shock or fire.
Do not use the unit in combustible or explosive gaseous atmospheres.
During putting equipment in hole on the metal panel while mechanical installation some metal burrs can
cause injury on hands, you must be careful.
Montage of the product on a system must be done with it’s fixing clamps. Do not do the montage of the
device with inappropriate fixing clamp. Be sure that device will not fall while doing the montage.
It is your responsibility if this equipment is used in a manner not specified in this instruction manual.
EMKO Elektronik warrants that the equipment delivered is free from defects in material and
workmanship. This warranty is provided for a period of two years. The warranty period starts from the
delivery date. This warranty is in force if duty and responsibilities which are determined in warranty
document and instruction manual performs by the customer completely.
Repairs should only be performed by trained and specialized personnel. Cut power to the device before
accessing internal parts.
Do not clean the case with hydrocarbon-based solvents (Petrol, Trichlorethylene etc.). Use of these
solvents can reduce the mechanical reliability of the device. Use a cloth dampened in ethyl alcohol or
water to clean the external plastic case.
1.3Installation
1.4Warranty
1.5Maintenance
1.6ManufacturerCompany
ManufacturerInformation:
Repairandmaintenanceserviceinformation:
EmkoElektronikSanayive Ticaret A.Þ.
DemirtaþOrganizeSanayiBölgesiKaranfilSk.No:616369BURSA/TURKEY
Phone:+902242611900
Fax:+902242611912
EmkoElektronikSanayive Ticaret A.Þ.
DemirtaþOrganizeSanayiBölgesiKaranfilSk.No:616369BURSA/TURKEY
Phone:+902242611900
Fax:+902242611912
TemperatureSensor
Input
HumiditySensorInput
0/2..10V,0/4..20mA or
ProNemMiniPMI-P
5.2 AlarmOutputGraphicsofESM-3722HT
i
Process High Alarm
ON
OFF
Alarm
Output
Process Value
Process Low Alarm
ON
OFF
Alarm
Output
ProcessValue
Deviation Band Alarm
ON
OFF
Alarm
Output
(- AlarmSet)
=Process Set Value (Temperature or Humidity)
Deviation Range Alarm
ON
OFF
Alarm
Output
ProcessValue
AlarmSet AlarmSet
(+AlarmSet)
(- AlarmSet) (+AlarmSet)
ProcessValue
5.3EggTrayRotatorOperationGraphicsofESM-3722HT
Egg Tray Rotator
Output Led
Egg Tray Rotator
Output
ü
1- Screen Blinking Temperature Sensor failure . Sensor connection is wrong or there is no sensor
connection. While this message shown on this display,if buzzer function selection is 3, 5, 7 or 8
internal buzzer starts to operate.
5.4 FailureMessagesinESM3722HatcherController
2 Screen Blinking H Sensor failure . Sensor connection is wrong or there is no sensor
connection. While this message shown on this display,if buzzer function selection is 4, 6,7 or 8
internal buzzer starts to operate.
- umidity
NTCinputtype
PTCinputtype
Termoresistanceinputtype
Humidityinputtype
Accuracy
SensorBreakProtection
ControlForm
RelayOutputs
OptionalSSRDriverOutput
TemperatureDisplay
HumidityDisplay
LEDDisplays
InternalBuzzer
Upprovals
:NTC(10k @25°C)
:PTC(1000 @25°C)
:PT-100IEC751(ITS90)
:0/2..10V 0/4..20mA MiniPMI-P
:±1%offullscale
:Upscale
:PIDorON/OFF
:5A@250V atResistiveLoad(HeatingOutput)
:3 A@250V atResistiveLoad(Humidificating, Alarm
andEggtrayrotatorOutput
:Maximum30mA,Maximum15V
:8mmRed4digitLEDDisplay
:8mmGreen4digitLEDDisplay
:P (Green),%(Green), C(Red), F(Red), Alarm(Red),
HumidifierOutput(Red),EggtrayrotatorOutput(Red)
HeatingOutput(Red),
: 83dB
:,
W
W
³
Z Z
V
V
, orProNem
o o
7. AutoTuneMetod
Starting Auto Tune (Limit Cycle Tuning)
Operation by the user :
•Adjust t
•Adjust auto tune selection parameter ( = )
• In the main screen and Temperature value
are should alternately.
“Atun”
emperature control on/off or PID parameter
( =1)
Auto Tune method is used for determining PID parameters used by the device.
If Auto Tune operation is finished without any problem,
the device saves the new PID coefficients, calculated
using the previously found “T” and “B” values, to
memory and continue to run.
parameter is adjusted automatically.
Temperature
Value
Time
Heating
Output
Time
B
T
Cancelling Auto Tune (Limit Cycle Tuning) operation :
1 - If sensor breaks;
2 - If auto tune operation can not be completed in 8 hours ;
3 - If user adjusts parameter ;
4- During auto tune operation if the user changes the temperature control from pid to on/off;
5 - If process set value is changed while auto tune operation is being performed;
Auto tune is canceled. “Atun” is not displayed. Then, without doing any changes in PID
parameters, device continues to run with previous PID parameters.
3- In main operating screen if the upper display is blinking, it means that temperature alarm exits and
alarm output is active . 1 5if buzzer function selection is , or 8 internal buzzer starts to operate.
4- In main operating screen if the lower display is blinking, it means that humidity alarm exits and alarm
output is active . 2 6if buzzer function selection is , or 8 internal buzzer starts to operate.
B C D E FG HI /
/
UV W Z/
/ 0
PowerSupplyVoltageA
TemperatureSensorInputB Scale( )°C/°F
ESM-3722
(77x35DINSize)
4
-20°C/-4°F; 80°C/176°F
115V ( %15)50/60Hz-1.5VAV±
ProNemMiniPMI-P
PT 100,IEC751(ITS90)
1
PTC(Not-1)
2
5230V ( %15)50/60Hz-1.5VAV±
8 10-30V 1.5W
Z
0°C/32°F;100°C/212°F
0°C/32°F;100°C/212°F
NTC(Not-1)
3
0°C/32°F;100°C/212°F
324V ( %15)50/60Hz-1.5VAV±
0
224V ( %15)50/60Hz-1.5VAW±
0%-100%
0%-100%
0%-100%
0/2..10VdcVoltageInput
4
50/4..20mA CurrentInput
6
HumiditySensorInputC Scale(%)
ProNemMiniPMI-P
0/2..10VdcVoltageInput
4
50/4..20mA CurrentInput
6
01 RelayOutput(3A@250V ,atResistiveLoad,1NO)V
HumidifierOutput
FG
1RelayOutput(5 A@250V ,atResistiveLoad1NC,1NO)V
HeatingOutputE
2SSRDriveOutput(Maximum30mA,Maximum15V)
01 RelayOutput(3A@250V ,atResistiveLoad,1NO)V
EggTryRotatorOutputHI
1RelayOutput(3A@250V ,atResistiveLoad,1NO)V
AlarmOutput
U
Temp.SensorwhichisgivenwithESM-3722
V
0None
3NTC-M5L20.K1.5 (NTCProbethermoplasticmouldedwith
1.5mcableforcoolingapplication)
4NTC-M6L50.K1.5 (
)
NTCProbestainlesssteelhousingwith
1.5mcableforcoolingapplication
9
ProNemMiniPMI-P (2 for TemperatureandHumidity
application)
.5mcable
6
Customer
1PTC-M6L40.K1.5(PTC AirProbe1.5msiliconcable)
2PTCS-M6L30.K1.5.1/8”(PTCLiquidProbewith1.5msiliconcable)
A
Userdefined
Userdefined
ESM-3722
ü
ESM-3722
ü
ESM-3722
ü
ESM-3722
ü
ESM-3722
ü
ESM-3722
ü
ESM-3722
ü
ESM-3722
ü
ü
PTC,NTC,PT-100
0/2..10V,0/4..20mA or
ProNemMiniPMI-P
6
2.3PanelMountingandRemoving
5.ChangingandSavingTemperatureandHumiditySetValue
5.1Ch miditySetValue
MainOperatingScreen
WhenSET buttonpressed‘’S’’ ledwill
beactiveandtemperaturesetvaluewill
bedisplayed.
TemperatureSetValueScreen
Temperaturesetvaluecan
bechangedwithincrement
anddecrementbuttons.
WhenSET buttonpressed
temperaturesetvaluecanbesaved.
GoesHumiditySET
valuescreen.
Temperaturesetvalueparameter(Default=37.4 )
Temperaturesetvalue,canbeprogrammedbetweenminimumtemperaturesetvalue and
maximumtemperaturesetvalue .
°C
WhenSET buttonpressed
setvaluecanbesaved.
Humidity
Goesbackto
mainoperationscreen.
HumiditySetValue Screen
If no operation is performed in Humidity set value changing mode and temperature set value
changing mode for 20 seconds, device turns to main operation screen automatically.
i
HumiditySetValue Screen
5.1 ProgrammingModeParameterList
In ON/OFF control algorithm, temperature
value is tried to keep equal to set value by
opening or closing the last control element.
ON/OFF controlled system, temperature
value oscillates continuously. Temperature
value’s oscillation period or amplitude around
set value changes according to controlled
system. For reducing oscillation period of
temperature value, a threshold zone is formed
below or around set value and this zone is
named hysteresis.
Temperature Sensor Offset Parameter ( Default = 0 )
3.2DeviceLabelandConnectionDiagram
3.ElectricalWiringDiagram
3.1SupplyVoltageInputConnectionoftheDevice
4.FrontPanelDefinitionand AccessingtotheMenus
5
7 8 11
9 10
12
BUTTON DEFINITIONS
1. Increment Button :
2. Decrement, Silencing Buzzer Button :
3. Manual Start of Egg Tray Rotator Operation Button:
**
4. Set Button:
5.Alarm led :
6. Heating Output Led :
7.Celcius led :
8.Fahrenheit led :
9. Led :
10. Output Led :
11.Precent Sign ledi :
12.Program led :
** In main operation screen, press this button to change display temperature and humidity sensor
value.
** It is used to increase the value in the Temperature and Humidity Set screens and Programming mode.
** It is used to decrease the value in the Set screen and Programming mode.
** It is used to silence the buzzer.
When the button is released the
engine start will be passive and engine stops.
** In the main operation screen; if this button pressed for the first time, Temperature set value will be
displayed. Value can be changed using increment and decrement buttons. When Set button is pressed
again, value is saved and Humidty set value will be displayed next. Value can be changed using
increment and decrement buttons. When Set button pressed again, value is saved and returns back to
main operating screen.
** To access the programming screen; in the main operation screen, press and hold this button for 5
seconds.
** It is used to save value in the Set screens (Temperature or Humidity) and programming screen.
**
** This led indicates that heating output is active.
** Indicates that device is in C mode.
** Indicates that device is in F mode.
** This led indicates that is active.
** This led indicates that output is active.
** Indicates that device is in programming mode .
o
o
In the main operation screen, if this button pressed engine starts.
It is active when alarm statuses.
Egg Tray Rotator Output
Humidity
** Indicates that device is in Humidity Set screen.
LED DEFINITIONS
Egg Tray Rotator Output
Humidificating
230V CONNECTION DIAGRAMV
TemperatureControlSelectionParameterOn/OfforPID (Default=0)
On - Off selected.
PID selected.
PID - Proportional Control Parameter ( Default =50 )
This parameter value can be adjusted form 0 to 100.
PID - Integral Parameter( Default = 1000 )
This parameter value can be adjusted form 0 to 3600.
PID - Derivative Parameter ( Default = 250 )
This parameter value can be adjusted form 0 to 3600.
PID -Period Time Parameter ( Default = 1 )
This parameter value can be adjusted form 1 to 50 second.
HumiditySensorScaleSelectionParameter(Default=0)
Buzzer Function Selection Parameter( Default = 0 )
Button Protection Parameter ( Default = 0 )
Humidity Alarm Function Selection Parameter ( Default = 0 )
Humidity (Default = 0)
When power is first applied to the device, this time delay must be expired for activation of
Humidity alarm.
Alarm Delay After Power On Parameter
It can be adjusted from 0 to 99 minutes.
Humidity Set Maximum Parameter(Default =Maximum Value of Device Scale)
if humidity alarm is active, this parameter value can be adjusted from humidity alarm set
minimum parameter to maximum value of the device scale.
Alarm
Humidity (Default = 0)
Humidity
Alarm On Delay Time Parameter
AlarmOnDelay Timecanbedefinedwiththisparameter.Itcanbeadjusted
from0to99minutes.
Buzzer is inactive.
Buzzer is active during temperature alarm
Buzzer is active during humidity alarm
Buzzer is active during Temperature sensor failures.
Buzzer is active during Humidity sensor failures.
Buzzer is active during Temperature sensor failures or temperature alarm.
Buzzer is active during Humidity sensor failures or Humidity alarm.
Buzzer is active during Temperature sensor failures or Humidity sensor failures
Buzzer is active during Temperature sensor failures or Humidity sensor failures
or temperature alarm or humidity alarm.
There is no protection.
Temperature setvalue can not be changed.
Humidity set value can not be changed.
Manual engine start is not available.
Humidity set value and Temperature set value can not be changed
Humidity set value can not be change and Manual engine start is not available.
Temperature set value can not be change and Manual engine start is not
available.
Temperature set value and Humidity set value can not be changed. Also
Manual engine start is not available.
Humiditysetvalueparameter(Default=60%)
Humiditysetvalue,canbeprogrammedbetweenminimumHumiditysetvalue andmaximum
temperaturesetvalue .
1-Before mounting the device in your panel, make
sure that the cut-out is of the right size.
2-Insert the device through the cut-out. If the
mounting clamps are on the unit, put out them
before inserting the unit to the panel.
3- Insert the mounting clamps to the fixing sockets
that located left and right sides of device and
make the unit completely immobile within the
panel
1-Pull mounting clamps from left and right
fixing sockets.
2-Pull the unit through the front side of the
panel
Before starting to remove the unit
from panel, power off the unit and
the related system.
c
Make sure that the power supply voltage is the same indicated on
the instrument.
Switch on the power supply only after that all the electrical
connections have been completed.
Supply voltage range must be determined in order. While installing
the unit, supply voltage range must be controlled and appropriate
supply voltage must be applied to the unit.
c
There is no power supply switch on the device. So a power supply
switch must be added to the supply voltage input.
Power switch must be two poled for seperating phase and neutral,
On/Off condition of power supply switch is very important in
electrical connection.
External fuse that on power supply inputs must be on phase
connection.
External fuse that on power supply inputs must be on (+)
connection.
V
Z
c
PowerSupplyInput
c
a
External
Fuse
(1A T)
Note-1
Supply
Switch
7 8
LN
Supply Voltage
230V ( %15) 50/60Hz ,
115V ( %15) 50/60Hz ,
24V ( %15)50/60Hz ,
24V ( %15) 50/60Hz ,
Z
V
V
V
W
±
±
±
±
10...30 V 1.5 W
Mustbedeterminedinorder.
ON
OFF
Temperature
Control
Output
Set
thSt
Time
thSt
Time
ü
3
4
1
2
5 6
9 10
7 8
11
12
TemperatureSetValueScreen HumiditySetValue Screen
Humiditysetvaluecanbe
changedwithincrementand
decrementbuttons.
RelayOutputs
2
135
468
7910
P/N: ESM-3722
L
N
a
PowerSupplyVoltage
230V ( %15) 50/60Hz ,
115V ( %15) 50/60Hz,
24V ( %15) 50/60Hz ,
24V ( %15) 50/60Hz ,
Z
V
V
V
W
±
±
±
±
10...30 V 1.5 W
11 12
TemperatureSensorInput
NTC,PTC,PT-100or
ProNemMiniPMI-P
HumiditySensorInput
0/2..10V,0/4..20mA or
ProNemMiniPMI-P
Mustbedeterminedinorder.
3
2
1
1
2
Mustbedeterminedinorder.
Mustbedeterminedinorder.
N
L
7 8 9 10
a
3x3 @250VA V
5A @250VV
LN
230 V ±15%
50/60Hz-1.5VA
V
2 3 41
ALARM
HUM.
5 6 11 12
14A TFuse
+
-
ENGINE
HEAT
N
L
7 8 9 10
a
3x3 @250VA V
5A @250VV
LN
230 V ±15%
50/60Hz-1.5VA
V
2 3 41
ALARM
HUM.
5 6 11 12
14A TFuse
+
-
ENGINE
HEAT
PTC Temperature and 0/4..20mA Humidity Sensor Input connection
VCC
GND
SCL
SDA
ProNem Mini PMI-P Temperature and Humidity Sensor Input Connection
Note: If this parameter is select 0, PID parameters ( , , , , ) will be not observed.
If this parameter select 1, parameter will be not observed.
Auto Tune (Limit Cycle Tuning) Selection Parameter ( Default = )
Device does not do(Limit cycle Tuning) operation.
Device does operation.
HysteresisParameterforTemperature(Default=0.1°C)
From 1 to 10°C for NTC,PTC, PT-100 (0°C, 100°C) ,From 1 to 18°F for NTC,PTC ,PT-100
(32°F, 212°F),From 0.1 to 10.0°C for NTC, PTC, PT-100 (0.0°C,100.0°C), From 0.1 to
18.0°F for NTC, PTC, PT-100 (32.0°F,212.0°F) ,From 1 to 10°C for ProNem Mini PMI-P
(-20°C, 80°C) ,From 1 to 18°F for ProNem Mini PMI-P (-4°F,176°F), From 0.1 to 10.0°C for
ProNem Mini PMI-P (-20.0°C,80.0°C), From 0.1 to 18.0°F for ProNem Mini PMI-P
(-4.0°F,176.0°F).
Minimum Temperature Set Value Parameter ( Default = 10.0°C)
Temperature set value can not be lower than this value. This parameter value can be
adjusted from minimum value of device scale to maximum temperature set value
parameter
Maximum Temperature Set Value Parameter ( Default = 40.0 °C )
Temperature set value can not be greater than this value.
This parameter value can be adjusted from minimum temperature set value parameter
to maximum value of the device scale.
From -10 to 10°C , NTC,PTC , PT-100 (0°C, 100°C)
From -18 to 18°F, NTC,PTC , PT-100 (32°F, 212°F)
From -10.0 to 10.0°C , NTC ,PTC , PT-100 (0.0°C,100.0°C)
From -18.0 to18.0°F NTC, PTC , PT-100 (32.0°F,212.0°F)
From -10 to 10°C ,ProNem Mini PMI-P ( -20°C, 80°C )
From -18 to 18°F,ProNem Mini PMI-P ( -4°F, 176°F )
From -10.0 to 10.0°C, ProNem Mini PMI-P ( -20.0°C, 80.0°C )
From -18.0 to18.0°F, ProNem Mini PMI-P ( -4.0°F,176.0°F )
0..10V 0..20mAZ Zor
2..10V 4..20mAZ Zor
(1) (2)
(2)(1)
It is valid, if the device type 0/2...10V
It is valid, if the device type 0/4...20mA
Z
Z
Humidity Sensor Input.
Humidity Sensor Input .
(1)
(2)
i
Analogue input range is determined with this parameter.
Note : parameter ProNem Mini PMI- type device are not observed.P
HysteresisParameterforHumidity(Default=1)
From 1 to 10 for Humidity Sensor (0%RH, 100%RH)
From 0.1to 10.0 for Humidity Sensor (0.0%RH,100.0%RH)
In ON/OFF control algorithm,
value is tried to keep equal to set value by
opening or closing the last control element.
ON/OFF controlled system, temperature
value oscillates continuously. Temperature
value’s oscillation period or amplitude
around set value changes according to
controlled system. For reducing oscillation
period of temperature value, a threshold
zone is formed below or around set value
and this zone is named hysteresis.
Humidity
ON
OFF
Humidity
Control
Output
Set
hhSt
Time
hhSt
Time
Maximum Humidity Set Value Parameter (Default = Maximum Value of Device Scale)
This parameter value can be
adjusted from minimum humidity set value parameter to maximum value of the
device scale.
Humidity set value can not be greater than this value.
Minimum Humidity Set Value Parameter (Default = Minimum Value of Device Scale)
set value can not be lower than this value. This parameter value can be adjusted
from minimum value of device scale to maximum set value parameter
Humidity
Humidity
Sensor Offset Parameter ( Default = 0.0 )Humidity
From -10 to 10 for Humidity Sensor (0%RH, 100%RH)
From -10.0 to 10.0 for Humidity Sensor (0.0%RH,100.0%RH)
Timeof AutomaticEggTrayRotator (Default=00:00)
Thisparametervaluecanbeadjustedform00:00to99:00minute/second.
Repeatcycleof AutomaticEggTrayRotator (Default=00:00)
Thisparametervaluecanbeadjustedform00:00to24:00hour/minute.
Alarm Output Function Selection Parameter ( Default = 0 )
Alarm is inactive.
Alarm-Temperature sensor failures.
Alarm-Humidity sensor failures.
Alarm-Temperature or Temperature sensor failures.
Alarm-Humidity or Humidity sensor failures.
Alarm-Temperature sensor failures or Humidity sensor failures.
Alarm-Temperature or Humidity or Temperature sensor failures or Humidity
sensor failures.
Note : if parameter value is 3 or 6 , , , , , or parameters are
observed.
Note : if parameter value is 4 or 6 , , , , , or parameters are
observed.
Temperature Alarm Set Parameter
Thisparametervaluecanbeprogrammedbetweentemperatureminimumalarmset
parameterandtemperaturealarmsetmaximum parameter.
( Default = 50.0 °C )
Temperature Alarm Function Selection Parameter ( Default = 0 )
Process High alarm selected.
Process Low alarm selected.
Deviation Band alarm selected.
Deviation Range alarm selected.
Alarm Set Maximum Parameter ( Default = Maximum Value of Device Scale)
if temperature alarm is active, this parameter value can be adjusted from temperature
alarm set value parameter to maximum value of the device scale.
Alarm Set Minimum Parameter (Default = Minimum Value of Device Scale)
if temperature alarm is active, this parameter value can be adjusted from minimum value of
device scale to temperature alarm set maximum parameter value.
Temperature Alarm Parameter
This parameter value can be adjusted form 0 to %50 of the device scale.
Hysteresis ( Default = 0)
Temperature AlarmOnDelayTimeParameter
Temperature AlarmOnDelay Timecanbedefinedwiththisparameter.Itcanbe
adjustedfrom0to99minutes.
(Default=0)
Temperature Alarm Delay After Power On Parameter
It can be adjusted from 0 to 99 minutes.
( Default = 0)
When power is first applied to the device, this time delay must be expired for activation of
temperature alarm.
Process High alarm selected.
Process Low alarm selected.
Deviation Band alarm selected.
Deviation Range alarm selected.
Humidity AlarmSetParameter
Thisparametervaluecanbeprogrammedbetweenhumidityminimumalarmset
parameterandhumidityalarmsetmaximum parameter.
(Default=50)
Humidity Set Minimum Parameter(Default =Minimum Valueof Device Scale)
if humidity alarm is active, this parameter value can be adjusted from minimum value of
device scale to humidty alarm set maximum parameter value.
Alarm
Humidity Alarm Parameter
This parameter value can be adjusted form 0 to %50 of the device scale.
Hysteresis ( Default = 0)
Buzzer ActiveTime
Ifbuzzerfunctionselectionparameter
Buzzeractivetimecanbedefinewiththisparameter.Itcanbeadjustedfrom1to99
minutes.Whenthisparameteris1,ifdecrementbuttonispressed, isobserved.In
thisconditionbuzzerisactivetillbuzzersilencebuttonispressed.
(Default= )
value=0,thisparameterisnotobserved.
Note-1: External Fuse is recommended
WHITE
YELLOW
BROWN
GREEN
ProNemMini
PMI-P
BLACK
Shield
Note: (Black)pinmustbeconnectedtonumber10(GND)oftheterminalblock.Shield
P/N:ESM-3722-5.2.5.0.1/01.01/1.0.0.0
7 8
a
3x3A@250V V
5A @250VV
L
230 V ±15%
50/60Hz -1.5VA
V
2 3 41
ALARM
PTC
5 6
ENGINE
HEAT
L N NNN N
0/4-20mA
HUM.
HUM.
INPUT
TEMP.
INPUT
9 10 11
P/N:ESM-3722-5.6.6.0.1/01.01/1.6.6.0
7 8 9 10
a
3x3A@250V V
5A @250VV
L
230 V ±15%
50/60Hz-1.5VA
V
2 3 41
ALARM
5 6
ENGINE
11 12
HEAT
L N NNN N
HUM.
ProNemMiniPMI-P
WHITE
BROWN
YELLOW
GREEN
VCC
GND
SCL
SDA
5.1 ProgrammingModeParameterList
Decimal Seperator Enabling Parameter ( Default = 0 )
None.
Only Temperature parameters with decimal seperator.
TemperatureUnitSelectionParameter (Default=0)
°C selected.
°F selected.
Only Humidity parameters with decimal seperator.
Only Temperature and Humidity parameters with decimal seperator.
Note : When value of or parameters are changed , the values of , , , ,
, , , , , , , , , , , , and parameters
should be changed accordingly.
0..10V veya 0..20mAZ Z
2..10V veya 4..20mAZ Z
Temperature SensorScaleSelectionParameter(Default=0)
(1) (2)
(2)(1)
Analogue(T inputrangeisdeterminedwiththisparameter.emperature)
Temperature
or
or
SensorScaleLowLimitParameter:(Default=0)
It can be adjusted from -1999 to ( -1). At this value analogue input becomes;
If =0,accordingtothedevicetype0V 0mA
If =1,accordingtothedevicetype2V 4mA
Z Z
Z Z
(1) (2)
(1) (2)
Temperature
or
SensorScaleHighLimitParameter:(Default=100)
Itcanbeadjustedfrom( +1)to9999. Atthisvalueanalogueinputbecomes;
According to the device type 10V 20mAZ Z
(1) (2)
Note : , parameters are shown, if the Temperature sensor analogue input type is selected .
Note : , and parameters are shown, if the Temperature sensor input type
( ) is selected.
analogue
0/2..10V or 0/4..20mA
ESM-3722
ü ü
ESM-3722
ESM-3722
ü ü
ESM-3722
ü
ESM-3722 ESM-3722
ü
Programming Mode Accessing Password
It is used for accessing to programming mode. It can be adjusted from 0 to 9999. If it is 0,
password is not entered for accessing to the parameters. When the password screen is not
set as “12” , If the user enters ‘12’ in password screen and parameters are
accessed and they can changed.
( Default = 0 )
Produkspesifikasjoner
| Merke: | Emko |
| Kategori: | Termostat |
| Modell: | ESM-3722 |
Trenger du hjelp?
Hvis du trenger hjelp med Emko ESM-3722 still et spørsmål nedenfor, og andre brukere vil svare deg
Termostat Emko Manualer
27 Oktober 2024
27 Oktober 2024
27 Oktober 2024
27 Oktober 2024
27 Oktober 2024
27 Oktober 2024
22 Oktober 2024
Termostat Manualer
- Termostat ORNO
- Termostat Bosch
- Termostat Boneco
- Termostat Siemens
- Termostat EBERLE
- Termostat Schwaiger
- Termostat AEG
- Termostat TP Link
- Termostat Oreg
- Termostat Netatmo
- Termostat Busch-Jaeger
- Termostat Brennenstuhl
- Termostat Danfoss
- Termostat Somfy
- Termostat Panasonic
- Termostat Schneider
- Termostat EMOS
- Termostat Heatit
- Termostat Dimplex
- Termostat Velleman
- Termostat GE
- Termostat Nexa
- Termostat Nobo
- Termostat Tru Components
- Termostat Bearware
- Termostat Elgato
- Termostat Avidsen
- Termostat STI
- Termostat Hunter
- Termostat Basetech
- Termostat TFA
- Termostat Tesla
- Termostat Renkforce
- Termostat REMKO
- Termostat ATAG
- Termostat Drayton
- Termostat Jung
- Termostat Ambiano
- Termostat Crestron
- Termostat Xavax
- Termostat Techno Line
- Termostat Remeha
- Termostat Heatmiser
- Termostat Wolf
- Termostat GENERAL Life
- Termostat Silvercrest
- Termostat AVM
- Termostat HomePilot
- Termostat Elektrobock
- Termostat Corberó
- Termostat Perel
- Termostat Delta Dore
- Termostat Homematic IP
- Termostat Vimar
- Termostat Emerson
- Termostat Salus
- Termostat Fenix
- Termostat Honeywell
- Termostat Junkers
- Termostat Eliwell
- Termostat Grasslin
- Termostat Jumo
- Termostat Enda
- Termostat Orbis
- Termostat Fantini Cosmi
- Termostat Vemer
- Termostat Qubino
- Termostat Theben
- Termostat EQ3
- Termostat Etherma
- Termostat Saunier Duval
- Termostat Gewiss
- Termostat Viessmann
- Termostat Bticino
- Termostat Conrad
- Termostat Econo-Heat
- Termostat Elro
- Termostat Gira
- Termostat Tado
- Termostat Brink
- Termostat Emmeti
- Termostat Itho
- Termostat Bryant
- Termostat Aube
- Termostat Baxi
- Termostat Seitron
- Termostat Amfra
- Termostat Vaillant
- Termostat Carel
- Termostat Buderus
- Termostat Optima
- Termostat Frico
- Termostat UPM
- Termostat Computherm
- Termostat Veria
- Termostat Innogy
- Termostat Nefit
- Termostat ICY
- Termostat Levica
- Termostat Itho-Daalderop
- Termostat Carrier
- Termostat Radson
- Termostat ChiliTec
- Termostat King
- Termostat ACV
- Termostat Landis Gyr
- Termostat Nest
- Termostat Oventrop
- Termostat IMIT
- Termostat Horstmann
- Termostat ELKO
- Termostat Alecto
- Termostat Google
- Termostat Wachendorff
- Termostat MundoControl
- Termostat Otio
- Termostat Rose LM
- Termostat Tylö
- Termostat Sinustec
- Termostat TrickleStar
- Termostat Finder
- Termostat Sygonix
- Termostat Warmup
- Termostat Plugwise
- Termostat Lowes
- Termostat Go Green
- Termostat Drayton Erie
- Termostat Intertechno
- Termostat EQ-3
- Termostat Johnson Control
- Termostat RWE
- Termostat Webasto
- Termostat Tellur
- Termostat OJ ELECTRONICS
- Termostat Zehnder
- Termostat Plieger
- Termostat HomeMatic
- Termostat Eneco
- Termostat VDH
- Termostat Maico
- Termostat Yokis
- Termostat Eurotronic
- Termostat HQ
- Termostat Ouellet
- Termostat THERMAFLEX
- Termostat Truma
- Termostat Wallair
- Termostat AWB
- Termostat PECO
- Termostat Worcester-Bosch
- Termostat 2Heat
- Termostat EasyTemp
- Termostat Hugo Muller
- Termostat Watts
- Termostat Westfalia
- Termostat Oregon Scientific
- Termostat H-Tronic
- Termostat Z-Wave
- Termostat Easy Timer
- Termostat Fibaro
- Termostat SPC
- Termostat Muller
- Termostat Bulex
- Termostat Helios (Amfra)
- Termostat IR-V
- Termostat Eqiva
- Termostat Hager
- Termostat Energenie
- Termostat Thermy
- Termostat Ferroli
- Termostat Niko
- Termostat Stiebel Eltron
- Termostat De Dietrich
- Termostat POER
- Termostat Technoline
- Termostat Magnum
- Termostat Cotech
- Termostat Hornbach
Nyeste Termostat Manualer
27 Oktober 2024
27 Oktober 2024
27 Oktober 2024
27 Oktober 2024
27 Oktober 2024
27 Oktober 2024
27 Oktober 2024
27 Oktober 2024
27 Oktober 2024
27 Oktober 2024