Fredrick Ramond FR45601BNI Bruksanvisning
Fredrick Ramond
Lampe
FR45601BNI
Les nedenfor 📖 manual på norsk for Fredrick Ramond FR45601BNI (3 sider) i kategorien Lampe. Denne guiden var nyttig for 3 personer og ble vurdert med 4.5 stjerner i gjennomsnitt av 2 brukere
Side 1/3
FR45601BNI/FBZ
MIME
ASSEMBLY I N STR UC TIONS
Assembly of this fixture will be accomplished by first assembling the main body,
installing the mounting hardware to the junction box, hanging the fixture and then
installing the shade and crystals.
SAFETY WARNING: Read wiring and grounding instructions [FRIS 18]
and any additional directions. Turn power supply off during installation. If new wiring
is required, consult a qualified electrician or local authorities for code requirements.
STEP 1
1
STEP 2 Refer to Hanging Instruction Sheet to hang fixture. Then refer[FRIS19-41 ]
back to this sheet to continue installation of this fixture.
STEP 3
1
2
3
[DRAWING 1]
Bulbs: 3-60W CAND. Replacement Parts: SHADE: R45601SH (BNI FINISH),
R455601AMBSH ( fbz FINISH),
R45602CRY-A
01.01.13
3d
ce
1b
e
4
2
5
After unpacking fixture main body can be installed prior to attaching the shade.
Take shade and line up holes in tabs with the holes in (1) (d)
end of arms . Shade tab shold be on top of the arm -see . (b) Drawing 1
Slip flat head screw (2) through hole in arm and hole in shade
tab. Thread barrel knob onto end of screw to secure shade.(3) (2)
Repeat process with the remaining arms.
Thread finial (4) onto threaded tube (t) found at the bottom of the fixture.
Attach crystals (5) at point (e) as indicated in .Drawing 1
e
5
t
4
HA GI NSTN NG I RUCT NSIO
FRIS19 41-
SA Y FET WA NG:RNI Read wiring and grounding instructions [FRIS 18]
and any additional directions. Turn power supply off during installation. If new wiring
is required, consult a qualified electrician or local authorities for code requirements.
EP 1ST
1 Shut off electrical current before starting. If the fixture you are replacing is
turned on and off by a wall switch, simply turn the switch off. If not, remove the
appropriate fuse (or open the circuit breakers) until the fixture is dead.
N• DO OT restore current - either by fuse, breaker or switch - until the new
fixture is completely wired and in place.
EP 2ST
[DRA N ]WI G 2
01.01.13
3
4
1 Prepare mounting strap (a) by threading screws (b) into appropriately threaded hole
(h) - see Drawing 1. Make sure spacing of screws matches spacing of mounting holes
(3) in Canopy (c) -see Drawing 2.
2 Install mounting strap (a) to junction box (j), with two 8-32 screws (1) - see Drawing 2.
1 To mount fixture to ceiling , slip screws (b) in mounting strap (a) through
holes (3) in canopy (c) - see Drawing 2.
2 Hold canopy (c) up to ceiling and thread deocrative knobs (4) onto end of
screws (b) and tighten to secure fixture to ceiling.
3 Return to previous instruction sheet to complete fixture assembly.
c
[DRA N ]WI G 1
EP 3ST
Make electrical connections from supply wire to fixture lead wires. Refer to
instruction sheet and follow all instructions to make all necessary [FRIS18]
wiring connections. Then refer back to this sheet to continue installation of
this fixture.
EPST 4
a
1
b
a
j
b
WIRING AND GROUNDING INSTRUCTIONS
SAFETY WARNING: Read wiring and grounding instructions
[FRIS 18] and any additional directions. Turn power supply off during installation. If new
wiring is required, consult a qualified electrician or local authorities for code require-
ments.
STEP 1 WIRING INSTRUCTIONS
Indoor Fixtures
1 Connect positive supply wire (a) (typically black or the smooth, unmarked side of
the two-conductor cord) to positive fixture lead (b) with appropriately sized twist
on connector - See Drawings 1 or 2.
2 Connect negative supply wire (c) (typically white or the ribbed, marked side of
the two-conductor cord) to negative fixture lead (d).
3 Please refer to the grounding instructions below to complete all electrical
connections.
Outdoor Fixtures
1 Connect positive supply wire (a) (typically black or the smooth unmarked side of
the two-conductor cord) to positive fixture lead (b) with appropriately sized twist
on connector - See Drawings 2 or 3.
2 Connect negative supply wire (c) (typically white or the ribbed, marked side of
the two-conductor cord) to negative fixture lead (d).
3 Cover open end of connectors with silicone sealant to form a watertight seal.
• If installing a wall mount fixture, use caulk to seal gaps between the fixture
mounting plate (backplate) and the wall. This will help prevent water from
entering the outlet box. If the wall surface is lap siding, use caulk and a fixture
mounting platform specially.
4 Please refer to the grounding instructions below to complete all electrical
connections.
STEP 2 GROUNDING INSTRUCTIONS
Flush Mount Fixtures
For positive grounding in a 3-wire electrical system, fasten the fixture ground
wire (e) (typically copper or green plastic coated) to the fixture mounting strap
(1) with the ground screw (2) - See Drawing 1.
Note: On straps for screw supported fixtures, first install the two mounting
screws in strap.
Any remaining tapped hole may be used for the ground screw.
Chain Hung Fixtures
Loop fixture ground wire (e) (typically copper or green plastic coated) under the
head of the ground screw (2) on fixture mounting strap (1) and connect to the
loose end of the fixture ground wire directly to the ground wire of the building
system with appropriately sized twist-on connectors - See Drawing 2.
Post-Mount Fixtures
Connect fixture ground wire (e) (typically copper or green plastic coated) to
power supply ground with appropriately sized twist-on connector inside post.
Cover open end of connector with silicone sealant to form a watertight seal - See
Drawing 3.
[drawing 1]
[drawing 2]
[drawing 3]
1.30.08
a c e
1
b d
supply wire
xture leads
twist-on
connectors
2
a c
e
e
1
b d
2
a c e
e
b d
twist-on
connectors
supply wire
xture leads
supply wire
xture leads
twist-on
connectors
FRIS18
Produkspesifikasjoner
| Merke: | Fredrick Ramond |
| Kategori: | Lampe |
| Modell: | FR45601BNI |
Trenger du hjelp?
Hvis du trenger hjelp med Fredrick Ramond FR45601BNI still et spørsmål nedenfor, og andre brukere vil svare deg
Lampe Fredrick Ramond Manualer
15 Oktober 2024
15 Oktober 2024
Lampe Manualer
- Lampe Ledlenser
- Lampe AFX
- Lampe Hama
- Lampe Neewer
- Lampe Hazet
- Lampe Philips
- Lampe Topeak
- Lampe Schwaiger
- Lampe Godox
- Lampe IKEA
- Lampe Samsung
- Lampe Sony
- Lampe Xiaomi
- Lampe Lutec
- Lampe Golden Lighting
- Lampe ET2
- Lampe Quoizel
- Lampe Crystorama
- Lampe Brennenstuhl
- Lampe Dainolite
- Lampe EMOS
- Lampe Nanlite
- Lampe BeamZ
- Lampe Livoo
- Lampe Flex
- Lampe Maxim
- Lampe Brandson
- Lampe Maginon
- Lampe Ansmann
- Lampe Makita
- Lampe Intermatic
- Lampe V-Tac
- Lampe JBL
- Lampe Nedis
- Lampe Elation
- Lampe Chauvet
- Lampe Karma
- Lampe Ridem
- Lampe Dedra
- Lampe Black Diamond
- Lampe Powerplus
- Lampe Ozito
- Lampe BenQ
- Lampe Hansa
- Lampe Livarno Lux
- Lampe Eurolite
- Lampe Casalux
- Lampe American DJ
- Lampe Profoto
- Lampe Petzl
- Lampe Gravity
- Lampe AVM
- Lampe Impact
- Lampe Olight
- Lampe Vimar
- Lampe Genaray
- Lampe Altman
- Lampe Setti+
- Lampe Kanlux
- Lampe Xline
- Lampe ARRI
- Lampe Osram
- Lampe Zhiyun
- Lampe Honeywell
- Lampe Perfect Christmans
- Lampe XCell
- Lampe Physa
- Lampe Jinbei
- Lampe Apa
- Lampe Bolt
- Lampe Heitronic
- Lampe HQ Power
- Lampe Currey & Company
- Lampe Deko-Light
- Lampe Angler
- Lampe Raya
- Lampe Livex Lighting
- Lampe Hinkley Lighting
- Lampe Norwell
- Lampe Ranex
- Lampe COLBOR
- Lampe Lucide
- Lampe Nicols
- Lampe Dorr
- Lampe Pixel
- Lampe Silva
- Lampe Allegri
- Lampe Rotolight
Nyeste Lampe Manualer
14 Mars 2025
14 Mars 2025
14 Mars 2025
14 Mars 2025
14 Mars 2025
13 Mars 2025
13 Mars 2025
13 Mars 2025
13 Mars 2025
13 Mars 2025