Klavis CalTrans Bruksanvisning

Les nedenfor 📖 manual på norsk for Klavis CalTrans (19 sider) i kategorien Ikke kategorisert. Denne guiden var nyttig for 2 personer og ble vurdert med 4.5 stjerner i gjennomsnitt av 2 brukere

Side 1/19
CalTrans
CalTrans
CalTrans
CalTrans CalTrans user manual V1.6 Page of 1 19
Ca
Ca
Ca
CaCal
l
l
llTra
Tra
Tra
TraTrans
ns
ns
nsns
V/Oct processor
Quad programmable Volt/Octave calibrator and transposer CV
Introduction
The CalTrans solves issues encountered when playing tonal music with a modular system:
tracking problems, curves unrelated to Volt per octave ratio, limited octave range, cumbersome
transpose, . The Caltrans corrects and expands the range of troublesome VCOs and brings V/Oct ..
tracking to anything that oscillates. Besides calibration, the CalTrans offers live play features.
Each channel can be quantized and any combination of them transposed jointly. VCOs whose
tracking doesn’t go high enough to follow the leader will see their pitch repositioned in their
highest possible octave so that the global harmony is unaffected. You can add a pinch of
portamento and glissando each channel and save the whole in user presets. to
CalTrans
CalTrans
CalTrans
CalTransCalTrans
Features at a glance
Four V/Oct processing channels, each with individual :
o Curve correction and range expansion for a VCOny , VCF or
other oscillating circuit with a CV acting on pitch
o 1-for-1 V/Oct mode for use without target calibration
o Switchable semitone quantizer
o Adjustable portamento time
o Adjustable glissando time
Dedicated semitone and octave transpose encoders
Inputs cascading with zero added load for stable pitch control
Four user presets storing transpose, portamento and glissando
Storage of the calibration profile for each channel
Maximum voltage range covering 10 octaves
Presets, calibration and current state retained over power cycle
Volt/Oct inputs factory-calibrated in flash memory
User adjustable input scaling to correct voltage inaccuracies in your
sources
Easy firmware update via a simple audio file
High-quality push-encoders with metal shaft
Skiff-friendly & compact module
New features described in this manual require firmware update 1.17
CalTrans
CalTrans
CalTrans
CalTrans CalTrans user manual V1.6 Page of 2 19
Installation and security
Purpose
This module is meant for installation in a Eurorack-compliant chassis.
It adheres to Eurorack Doepfer mechanical and electrical specifications.
Do not attempt using this module in other mechanical or electrical contexts.
Installation
Before the installation, disconnect the mains power supply from your modular system. Some
power supplies are not safely isolated; there is a risk of injury!
See in the specifications if this module requires 5V from the supply rails. If 5V is needed and your
rack is not providing 5V, do not attempt connection!
Check that the current consumption requirements of this module, when added to your installed
set of modules do not exceed the available current from your supply. This is done by adding up
the current draw of all modules (mA) separately for each of 5V, 12V and -12V rails. If any of these 3
sums exceeds the available current of your supply for that voltage, do not connect the module to
your system; you need a stronger power supply.
The provided supply flat cable can only be inserted in the appropriate orientation at the back of
the module, so there is no risk of error on that end. However, you should pay attention to the
orientation of the cable in the socket of the supply PCB inside your chassis. Cheap sockets
without shrouding may allow you to plug in the connector the wrong way!
The red stripe on the cable should match a stripe printed on the supply board. The stripe also
indicates the -12V side. In case there is no stripe, a -12V marking is a safe indication of the
orientation.
Double check that the connectors are fully inserted and correctly oriented before switching on
the power supply. In case of an anomaly, switch off the power supply immediately and check
everything again.
CalTrans
CalTrans
CalTrans
CalTrans CalTrans user manual V1.6 Page of 3 19
Firmware update
Once acquiring your CalTrans, go the Klavis web site, download and install the latest firmware.
The product can be updated by playing an audio file such as “ .wav”.CalTrans_1.xx
Procedure
Connect a mono cable between your audio playing device headphone output and the
CalTrans calibration input.
Prepare to play the audio file
Set the play level at two thirds
While pressing the channel 1 and Qtz buttons, switch on your modular case supply
The six yellow LEDs will flash
Start playing the audio file
If everything goes fine
After a while, the first yellow LED will go on
As the update is progressing, the following yellow LEDs will also go on
When the green LED is flashing, the firmware is updated successfully
Press the top encoder to restart the module
If the sound level is too low
Two red LEDs will blink alternately
Stop audio playback
Slightly increase the audio playback level
Press the bottom encoder button
Start audio playback from the beginning
If there is an error during the playback
This is indicated by the 4 red LEDs
It is possible that the sound setting was too loud to begin with .
Diminish the sound level drastically and restart the procedure.
Playback error can also be due to various parasitic sound causes:
Touching the cable
Using sound-generating features of your phone or computer
Some power saving feature affecting the audio playback
Surrounding noisy modules, bad electrical grounding or modular supply noise
Having some sound enhancing processing (3D, compression, etc) being active

Produkspesifikasjoner

Merke: Klavis
Kategori: Ikke kategorisert
Modell: CalTrans

Trenger du hjelp?

Hvis du trenger hjelp med Klavis CalTrans still et spørsmål nedenfor, og andre brukere vil svare deg




Ikke kategorisert Klavis Manualer

Ikke kategorisert Manualer

Nyeste Ikke kategorisert Manualer