Klavis Flexshaper Bruksanvisning

Klavis Ikke kategorisert Flexshaper

Les nedenfor 📖 manual på norsk for Klavis Flexshaper (13 sider) i kategorien Ikke kategorisert. Denne guiden var nyttig for 2 personer og ble vurdert med 4.5 stjerner i gjennomsnitt av 2 brukere

Last ned PDF

Side 1/13

Flexshaper

Flexshaper Flexshaper user manual V1.3 Page of 1 13

FFle

lelex

xxs

ssha

hahap

ppe

eer

rr voltage mapper

CV-controlled voltage mapper and waveshaper

Introduction

The Flexshaper is a highly versatile module when it comes to modify evolving voltages in other

directions and levels. Five settings allow you to fold/expand/clip/compress/invert partially or

completely any or audio signal. The module can act as an envelope-shaping tool, frequency CV

multiplier, waveshaper, clipper, distortion, limiter, curve changer, and more. Five CV inputs offer

limitless control over the placement of the voltage points for dynamic signal sculpting.

Flexshaper

FlexshaperFlexshaper

Features at a glance

• Process from DC to full audio range

• Unipolar/bipolar input mode switch

• Nominal & clip level LEDs

• Output signal LED

• Input gain knob for nominal level setting,

allows clean flat clipping when overdriven

• Five manual voltage mapping potentiometers

• Five CV control of the voltage mapping points

• Simultaneously active unipolar and bipolar outputs

• Firmware update via a simple audio file

• Compact and skiff-friendly module

Flexshaper

Flexshaper Flexshaper user manual V1.3 Page of 2 13

Installation and security

Purpose

This module is meant for installation in a Eurorack-compliant chassis.

It adheres to Eurorack Doepfer mechanical and electrical specifications.

Do not attempt using this module in other mechanical or electrical contexts.

Installation

Before the installation, disconnect the mains power supply from your modular system. Some

power supplies are not safely isolated; there is a risk of injury!

See in the specifications if this module requires 5V from the supply rails. If 5V is needed and your

rack is not providing 5V, do not attempt connection!

Check that the current consumption requirements of this module, when added to your installed

set of modules do not exceed the available current from your supply. This is done by adding up

the current draw of all modules (mA) separately for each of 5V, 12V and -12V rails. (1000mA = 1

amp). If any of these 3 sums exceeds the available current of your supply for that voltage, do not

connect the module to your system; you need a stronger power supply.

The provided supply flat cable can only be inserted in the appropriate orientation at the back of

the module, so there is no risk of error on that end. However, you should pay attention to the

orientation of the cable in the socket of the supply PCB inside your chassis. Cheap sockets

without shrouding may allow you to plug in the connector the wrong way!

The red stripe on the cable should match a stripe printed on the supply board. The stripe also

indicates the -12V side. In case there is no stripe, a -12V marking is a safe indication of the

orientation.

Double check that the connectors are fully inserted and correctly oriented before switching on

the power supply. In case of an anomaly, switch off the power supply immediately and check

everything again.

Flexshaper

Flexshaper Flexshaper user manual V1.3 Page of 3 13

Firmware update

If needed, the product can be updated by playing an audio file such as “Flexshaper_1.00.wav”.

Not finding any file on Klavis web product’s page means there is no update available.

Procedure

• Connect a mono or stereo cable between your audio playing device headphone output

and the Flexshaper input.

• Prepare to play the audio file

• Set the play level of your playing device at two thirds

• While pressing the Bipolar button, switch on your modular case supply

• The yellow LED will flash

• Start playing the audio file

If everything goes fine

• The yellow LED will go steady es on

• As the update is progressing, the output white LED will go brighter

• When the white and green LEDs are flashing, the firmware is updated successfully

• Press the button to restart the module

If the sound level is too low

• The red, yellow and white LEDs will blink

• Stop audio playback

• Slightly increase the audio playback level

• Press the button

• Start audio playback from the beginning

If there is an error during the playback

• The red and white LEDs will blink

It is possible that the sound setting was too loud to begin with.

Diminish the sound level drastically and restart the procedure.

Playback error can also be due to various parasitic sound causes:

• Touching the cable

• Using sound-generating features of your phone or computer

• Some power saving feature affects the audio playback

• Surrounding noisy modules, bad electrical grounding or modular supply noise

Produkspesifikasjoner

Merke:	Klavis
Kategori:	Ikke kategorisert
Modell:	Flexshaper

Trenger du hjelp?

Hvis du trenger hjelp med Klavis Flexshaper still et spørsmål nedenfor, og andre brukere vil svare deg

Ditt navn*

Din e-post*

Skriv spørsmålet ditt her

Ikke kategorisert Klavis Manualer

Klavis CalTrans Bruksanvisning

16 Oktober 2024

Klavis Flexshaper Bruksanvisning

16 Oktober 2024

Ikke kategorisert Manualer

Nyeste Ikke kategorisert Manualer

Daewoo Cyclone Essential FLR00038 Bruksanvisning

28 Oktober 2024

IFM SU6631 Bruksanvisning

28 Oktober 2024

IFM SU7031 Bruksanvisning

28 Oktober 2024

IFM SV8051 Bruksanvisning

28 Oktober 2024

Daewoo AVS1464 Bruksanvisning

28 Oktober 2024

IFM PT5300 Bruksanvisning

28 Oktober 2024

IFM KTE301 Bruksanvisning

28 Oktober 2024

IFM OVP810 Bruksanvisning

28 Oktober 2024

IFM SF0516 Bruksanvisning

28 Oktober 2024

IFM TSM701 Bruksanvisning

28 Oktober 2024